Acceder

Bibliografías temáticas / Concrete Testing Mathematical models / Tesis

Siga este enlace para ver otros tipos de publicaciones sobre el tema: Concrete Testing Mathematical models.

Tesis sobre el tema "Concrete Testing Mathematical models"

Autor: Grafiati

Publicado: 4 de junio de 2021

Última modificación: 29 de enero de 2023

Crea una cita precisa en los estilos APA, MLA, Chicago, Harvard y otros

Elija tipo de fuente:

Consulte los 50 mejores tesis para su investigación sobre el tema "Concrete Testing Mathematical models".

Junto a cada fuente en la lista de referencias hay un botón "Agregar a la bibliografía". Pulsa este botón, y generaremos automáticamente la referencia bibliográfica para la obra elegida en el estilo de cita que necesites: APA, MLA, Harvard, Vancouver, Chicago, etc.

También puede descargar el texto completo de la publicación académica en formato pdf y leer en línea su resumen siempre que esté disponible en los metadatos.

Explore tesis sobre una amplia variedad de disciplinas y organice su bibliografía correctamente.

1

Lanzas, Lourdes Eneida 1962. "A parametric study on the behavior of slender reinforced concrete frames." Thesis, The University of Arizona, 1989. http://hdl.handle.net/10150/276945.

Texto completo

Resumen

By using a nonlinear computer analysis, a parametric study is developed in order to examine the accuracy of the Moment Magnifier Method of the American Concrete Institute Code (ACI 318-83). The variables used in the parametric study are: axial load intensity, P/Po; column reinforcement ratio, rho; slenderness ratio, klu; shape of column cross section, flexural stiffness ratio, and distribution of axial loads. In the parametric study, 216 cases of single bay fixed-base portal frames are examined. The higher moment for each one of these frames at failure are then compared with the design moment predicted by the Moment Magnifier Method of the American Concrete Institute Code (ACI 318-83). The Moment Magnifier Method proved to be very conservative when the columns are subjected to high level of axial loads and when the slenderness ratio is increased.

Los estilos APA, Harvard, Vancouver, ISO, etc.

2

Lam, Wai-yin, and 林慧賢. "Plate-reinforced composite coupling beams: experimental and numerical studies." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2006. http://hub.hku.hk/bib/B37311797.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

3

Chan, Ka-ho Enoch, and 陳家灝. "Experimental and numerical studies of concrete beams prestressed with unbonded tendons." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2008. http://hub.hku.hk/bib/B40988004.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

4

Lokuge, W. P. (Weena Priyanganie) 1967. "Stress-strain behaviour of confined high strength concrete under monotonically increasing and cyclic loadings." Monash University, Dept. of Civil Engineering, 2003. http://arrow.monash.edu.au/hdl/1959.1/9425.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

5

Tasnimi, A. A. "Prediction of forces within prestressed sections : The behavior of simply supported prestressed concrete beams with boned and unbonded tendons predicted by mathematical model and investigated by testing to destruction using two point load." Thesis, University of Bradford, 1988. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.384298.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

6

Thölken, Denise. "Efeito da rigidez de pilar parede no comportamento sísmico de edifício de concreto armado." Universidade Tecnológica Federal do Paraná, 2013. http://repositorio.utfpr.edu.br/jspui/handle/1/962.

Texto completo

Resumen

Este trabalho tem como objeto o estudo do efeito da rigidez de pilar parede no comportamento estrutural de edifícios de concreto armado submetidos a sismos. Foram consideradas as premissas da norma brasileira ABNT NBR15421:2006, que apresenta os critérios para projeto de estruturas resistentes a sismo. A análise linear com emprego dos métodos da norma - método das forças horizontais equivalentes, método espectral e histórico de aceleração no tempo - foi aplicada em edifícios com dois tipos de sistemas estruturais, sendo eles pórtico de concreto e sistema dual pórtico de concreto e pilar parede. Os resultados foram analisados nos pórticos de extremidade das estruturas nos sentidos longitudinal (x) e transversal (y), comparando-se os deslocamentos de cada pavimento e esforços cortantes, momento fletor e normal nas bases dos pilares. A comparação foi realizada entre os três métodos aplicados e os sistemas estruturais analisados.<br>The aim of this work is to study the stiffness effect of wall columns on structural behavior of reinforced concrete buildings subjected to seismic action. The premises of the Brazilian standard ABNT NBR14521:2006 were considered, which presents criteria for earthquake resistant design of structures. The linear analysis employed the methods of the Brazilian standard - equivalent static load method, response spectrum analysis and time history method - were applied to buildings with two types of structural systems, namely concrete frame and dual system concrete frame and wall columns. The results were analyzed in edge frames structures in the longitudinal and transverse directions, comparing the displacement of each floor and shear, bending moment and axial forces on the bases of the columns. A comparison was made between the three methods applied and the structural systems analyzed.

Los estilos APA, Harvard, Vancouver, ISO, etc.

7

Ng, Ah Book. "Physical models in fire study of concrete structures." Thesis, McGill University, 1988. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=64055.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

8

Pessôa, José Renato de Castro. "Análise numérico-experimental de estruturas de concreto com utilização da energia de fraturamento." Universidade do Estado do Rio de Janeiro, 2007. http://www.bdtd.uerj.br/tde_busca/arquivo.php?codArquivo=780.

Texto completo

Resumen

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior<br>A evolução dos concretos utilizados nas últimas décadas deu origem ao Concreto de Alto Desempenho (CAD), que tem, entre suas características, alta resistência à compressão e baixa permeabilidade. Com o desenvolvimento dos produtos químicos utilizados na construção civil, em especial os superplastificantes e superfluidificantes, a utilização desse tipo de concreto tornou-se cada vez mais freqüente pela possibilidade de se obter uma mistura suficientemente trabalhável utilizando-se fatores água/cimento menores do que 0,35. Devido à sua microestrutura mais homogênea, esse tipo de concreto apresenta um comportamento mais frágil do que os concretos convencionais, exigindo uma melhor caracterização do material. A partir do final da década de 70 começou-se a aplicar os conceitos da Mecânica da Fratura para análise do comportamento de estruturas construídas com esse tipo de concreto. Como em algumas situações a resistência nominal de peças de concreto diminui com o aumento de suas dimensões, houve a necessidade de se considerar o efeito de escala das estruturas a fim de se obter níveis de segurança mais adequados no seu dimensionamento, o que justificou a utilização da Mecânica da Fratura. Neste trabalho a energia de fraturamento foi obtida experimentalmente pelo método do trabalho de fraturamento e pelo método do efeito de escala, por meio de ensaios estáveis de flexão de três pontos em amostras de concreto de alto desempenho com entalhe. Foi também desenvolvida a simulação numérica de uma viga com entalhe, analisada pelo método dos elementos finitos e empregando-se na modelagem constitutiva os conceitos da Mecânica da Fratura aplicada ao concreto. As vigas foram moldadas e ensaiadas no Instituto Politécnico do Rio de Janeiro (IPRJ) da Universidade do Estado do Rio de Janeiro (UERJ) na cidade de Nova Friburgo. Os ensaios foram realizados com controle de deslocamento da célula de carga. Foram ensaiadas três séries de 12 vigas, com quatro dimensões diferentes, geometricamente proporcionais, e três amostras para cada dimensão, totalizando 36 vigas. As alturas utilizadas para as vigas foram 38, 76, 152 e 304 mm, e sua espessura foi mantida constante igual a 38 mm. Os corpos de prova cilíndricos, para caracterização da resistência à compressão do concreto, foram moldados no IPRJ e rompidos no laboratório de engenharia civil da UERJ, na cidade do Rio de Janeiro. Os concretos utilizados apresentaram resistência à compressão média de 70 MPa.<br>The evolution of the concrete mixes used during the last decades gave birth to the High Performance Concrete (HPC), which, among its main characteristics, presents high strength and low permeability. With the development of chemical products used in civil engineering constructions, mainly the superplasticizers, the use of this kind of concrete has become more and more frequent due to the possibility of obtaining a workable mixture with a water/cement ratio lower than 0.35. Due to its more homogeneous microstructure, the HPC presents a more fragile behavior than the conventional concrete, demanding a better characterization of the material. At the end of the 1970s, concepts of the Fracture Mechanics started to be used for the analysis of the structural behavior of concrete structures. As the nominal stress of the material decreases as the size of the structure increases, it became necessary to consider this size effect in the analysis in order to obtain more suitable levels of security. This fact justifies the use of the Fracture Mechanics in the structural analysis of concrete structures. In this work, the fracture energy was experimentally obtained using the work-offracture method and the size effect method by performing three-point bend tests in HPC notched beams. It was also developed a numerical simulation of the tests, performing the analysis through the Finite Element Method and applying the concepts of the Fracture Mechanics of Concrete into the constitutive model. The notched beams were molded and tested at the Polytechnic Institute of the State University of Rio de Janeiro (IPRJ/UERJ), located in the city of Nova Friburgo. The tests were controlled by the vertical displacement of the load cell. Three series of twelve beams with four geometrically similar sizes were tested. Three samples for each size were cast, making an amount of 36 beams. The beams were 38, 76, 152 and 304 millimeters high and the width was kept constant equal to 38 millimeters. To characterize the concrete compression strength, 100x200 millimeters cylinders were molded at the IPRJ and tested at the UERJ civil engineering laboratory in the city of Rio de Janeiro. The tested concretes presented a medium compressive strength of 70 MPa.

Los estilos APA, Harvard, Vancouver, ISO, etc.

9

Ferdjani, Omar. "Behaviour of a one cell prestressed concrete box girder bridge : analytical study." Thesis, McGill University, 1987. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=66163.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

10

CHENG, YEOU-YEN. "MULTIPLE-WAVELENGTH PHASE SHIFTING INTERFEROMETRY (OPTICAL-TESTING, ASPHERIC SURFACE)." Diss., The University of Arizona, 1985. http://hdl.handle.net/10150/187928.

Texto completo

Resumen

The problems of combining ideas of phase shifting interferometry (PSI) and synthetic-wavelength techniques to extend the phase measurement range of conventional single-wavelength PSI are investigated. This combination of PSI and synthetic-wavelengths gives multiple-wavelength phase-shifting interferometry the advantages of: (1) larger phase measurement range and (2) higher accuracy of phase measurement. Advantages, error sources, and limitations of single-wavelength PSI are discussed. Some practical methods to calibrate the piezoelectric transducer (PZT), used to phase shift the reference beam, are presented with experimental results. Two methods of two-wavelength PSI are used to solve the 2π ambiguity problem of single-wavelength PSI. For the first method, two sets of phase data (with 2π ambiguities) for shorter wavelengths are calculated and stored in the computer which calculates the new phase data for the equivalent-wavelength λ(eq). The "error magnification effect," which reduces the measurement precision of the first method, is then investigated. The second, more accurate method, uses the results of the first method as a reference to correct the 2π ambiguities in the single-wavelength phase data. Experimental results are included to confirm theoretical predictions. The enhancement of two-wavelength PSI is investigated, and requires the phase data of a third wavelength. Experiments are performed to verify the capability of multiple-wavelength PSI. For the wavefront being measured, the difference of the optical-path-difference (OPD) between adjacent pixels is as large as 3.3 waves. After temporal averaging of five sets of data, the repeatability of the measurement is better than 2.5 nm (0.0025%) rms (λ = 632.8 nm). This work concludes with recommendations for future work that should make the MWLPSI a more practical technique for the testing of steep aspheric surfaces.

Los estilos APA, Harvard, Vancouver, ISO, etc.

11

Loria-Salazar, Luis Guillermo. "Reflective cracking of flexible pavements literature review, analysis models,and testing methods /." abstract and full text PDF (free order & download UNR users only), 2008. http://0-gateway.proquest.com.innopac.library.unr.edu/openurl?url_ver=Z39.88-2004&rft_val_fmt=info:ofi/fmt:kev:mtx:dissertation&res_dat=xri:pqdiss&rft_dat=xri:pqdiss:1453593.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

12

Seid, Hamid Jemila. "New residuals in multivariate bilinear models : testing hypotheses, diagnosing models and validating model assumptions /." Uppsala : Dept. of Biometry and Engineering, Swedish University of Agricultural Sciences, 2005. http://epsilon.slu.se/200583.pdf.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

13

Alluri, Chandra M. "Testing calculation engines using input space partitioning and automation." Fairfax, VA : George Mason University, 2008. http://hdl.handle.net/1920/3228.

Texto completo

Resumen

Thesis (M.S.)--George Mason University, 2008.<br>Vita: p. 158. Thesis director: Jeff Offutt. Submitted in partial fulfillment of the requirements for the degree of Master of Science in Software Engineering. Title from PDF t.p. (viewed Aug. 27, 2008). Includes bibliographical references (p. 156-157). Also issued in print.

Los estilos APA, Harvard, Vancouver, ISO, etc.

14

Banan, Roshan Aerospace Civil &amp Mechanical Engineering Australian Defence Force Academy UNSW. "An engineering approach to modelling ballistic impact on hybrid polymer laminates." Publisher:University of New South Wales - Australian Defence Force Academy. Information Technology & Electrical Engineering, 2009. http://handle.unsw.edu.au/1959.4/44094.

Texto completo

Resumen

Hybrid polymer laminates of polycarbonate and PMMA have generated considerable interest among researchers as an alternative to traditional glass armours because of their potential for reduced cost and weight. Generally, the development of ballistic armour is carried out experimentally which is an expensive task in terms of time and cost. Numerical simulation provides a much greater facility to understand the phenomenon of ballistic impact and the effects of various parameters on the response to such impact. In addition it provides an easy means of comparing the impact performance of different materials as well as combination of materials forming hybrid laminates. The aim of this research was to develop a numerical modelling capability to simulate the ballistic response of hybrid polymer laminates, specifically polycarbonate and PMMA, using a commercially available finite element code LS-DYNA. The challenge was to work within the limitations of the material models and the failure algorithms available within LS-DYNA, and still try to reproduce the behaviour observed experimentally by previous researchers, initially on monolithic plates of polycarbonate and PMMA and then on hybrid laminates. The first part of the study focuses on a detailed literature survey on mechanical and dynamic characterisation of polycarbonate and PMMA as well as experimental and numerical studies previously conducted on ballistic behaviour of these materials as well as their combinations. The material properties of the polymers compiled from this literature survey were used as input for the selected LS-DYNA material model. Impact simulations were carried on monolithic and laminated media of polycarbonate and PMMA and where possible these were compared to experimental results. It was observed that the results agreed with the experimental data qualitatively. Quantitatively the results showed some discrepancies which were attributed to the limitations faced in simulating the exact test conditions numerically. Numerical simulations were carried out to study the effects of variations in laminate thickness and plate support diameters as well as to examine the influence of the bond between the layers. Finally the impact response of four different combinations of polycarbonate and PMMA are compared to each other for different laminate thicknesses.

Los estilos APA, Harvard, Vancouver, ISO, etc.

15

Ozturk, Hande Isik. "Parametric Study On Selected Mathematical Models For Dynamic Creep Behavior Of Asphalt Concrete." Master's thesis, METU, 2007. http://etd.lib.metu.edu.tr/upload/12609023/index.pdf.

Texto completo

Resumen

Rut formation has long been recognized as a distress mechanism in flexible pavements. One of the causes of rut formation in flexible pavements is permanent deformation of uppermost asphalt concrete layers due to repeatedly applied traffic loading. The long term permanent deformation of asphalt concrete under repeated load is commonly called as dynamic creep. The primary objective of this thesis is to examine dynamic creep behavior of asphalt concrete specimens tested in laboratory and also study some suitable mathematical models for representing dynamic creep behavior. In this study, a set of uniaxial repeated load creep tests were performed on standard Marshall specimens prepared at three different bitumen contents. The effects of bitumen content and test condition parameters on dynamic creep behavior are examined. Among several mathematical creep models suggested by researchers, two well known models and a model proposed by the author are selected for representing the laboratory creep behavior. For each of these models, the interactions of the model parameters with varying bitumen content and test conditions are studied to detect probable definite trends, and to evaluate whether some relations for the model parameters as functions of bitumen content and test conditions can be developed or not. The results of analyses showed that all three mathematical models used in this study are successful in representing the laboratory dynamic creep behavior of asphalt concrete. The Power Model which has only two parameters is found to be the most stable and suitable model for parametric study among the three selected models. More consistent and definite interactions are observed between the parameters of this model and test conditions. However, within the scope of this study, no relations could be developed for the parameters of selected models as functions of bitumen content and test conditions because of limited test data.

Los estilos APA, Harvard, Vancouver, ISO, etc.

16

Ferdjani, Aissam. "Behaviour of concrete under generalized biaxial loadings." Thesis, McGill University, 1987. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=63762.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

17

Kleinow, Torsten. "Testing continuous time models in financial markets." Doctoral thesis, [S.l. : s.n.], 2002. http://deposit.ddb.de/cgi-bin/dokserv?idn=965412091.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

18

Khaled, Amar. "Behaviour of a two-cell prestressed concrete box girder bridge : analytical study." Thesis, McGill University, 1988. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=64019.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

19

Joucdar, Karim. "Behaviour of a two-cell prestressed concrete box girder bridge : experimental study." Thesis, McGill University, 1988. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=63981.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

20

Hon, Alan 1976. "Compressive membrane action in reinforced concrete beam-and-slab bridge decks." Monash University, Dept. of Civil Engineering, 2003. http://arrow.monash.edu.au/hdl/1959.1/5629.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

21

Carroll, James M. "The psychometrics of a bipolar valence activation model of self-reported affect." Thesis, National Library of Canada = Bibliothèque nationale du Canada, 2000. http://www.collectionscanada.ca/obj/s4/f2/dsk2/ftp03/NQ56520.pdf.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

22

Scholey, Kenneth Erwin. "Heat tranfser and crack formation in water-cooled zinc fuming furnace jackets." Thesis, University of British Columbia, 1991. http://hdl.handle.net/2429/30078.

Texto completo

Resumen

In the zinc slag fuming process, zinc is extracted from lead blast furnace slag by reduction with a coal/air mixture injected into the slag through submerged tuyeres. The furnace is constructed of water-cooled jackets to contain the molten bath and freeze a protective slag layer. The slag layer greatly reduces vessel wear caused by the corrosive and violently agitated bath. However, the jackets are known to develop cracks in the working face panel that initiate on the slag face and propagate towards the water cavity. If the cracks reach the water cavity explosions may result should the molten slag come into contact with the water. In this study an analysis of heat transfer in the jacket has been carried out using in-plant measurements and mathematical modelling. The working face of a water jacket was instrumented with thermocouples and positioned in a fuming furnace at the Trail smelter of Cominco Ltd. Measurements revealed the presence of large thermal transients or temperature "spikes" in the panel approximately 20 cm above the tuyeres. The transients were observed during charging and tapping of the furnace and are likely associated with slag fall-off due to surface wave action and gas injection effects when the bath level is low. Temperatures at the mid-thickness were seen to rise by as much as 180 °C above the steady-state level. Under these conditions large compressive stresses are produced in the panel that are sufficient to cause yielding. Over time, the transients lead to low-cycle fatigue of the working face panel with crack formation initiating at pre-existing surface flaws. A mathematical modelling analysis of the transient freezing phenomena has been carried out using the finite element method. The results indicate that the temperature spikes are associated with the sudden removal of patches of slag and molten slag coming into direct contact with the jacket. The temperature spikes are large enough to generate compressive stresses that cause yielding of the material in the exposed area. In order to reduce the damage caused by the removal of the slag shell an increased number of anchoring studs should be used in critical areas and a higher water circulation velocity should be employed to increase the size of the frozen slag layer and its strength.<br>Applied Science, Faculty of<br>Materials Engineering, Department of<br>Graduate

Los estilos APA, Harvard, Vancouver, ISO, etc.

23

Leung, Hugh, and 梁修賢. "Analysis of natural and hybrid ventilation in simple buildings." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2003. http://hub.hku.hk/bib/B26663107.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

24

Reller, Susan R. "Reliability diagnostic strategies for series systems under imperfect testing." Thesis, Virginia Tech, 1987. http://hdl.handle.net/10919/45926.

Texto completo

Resumen

An expected cost model was developed for failure detection in series systems under imperfect testing. Type I and type II error probabilities are included and single-pass sample paths are required. The model accounts for the expected costs of testing components, false positive termination, and no-defect-found outcomes. Based on the model, a heuristic was developed to construct the cost minimizing testing sequence. The heuristic algorithm utilizes elementary arithmetic computations and has been successfully applied to a variety of problems. Furthermore, the algorithm appears to be globally convergent. Choice of a starting solution affects the rate of convergence, and guidelines for selecting the starting solution were discussed. Implementation of the heuristic was illustrated by numerical example.<br>Master of Science

Los estilos APA, Harvard, Vancouver, ISO, etc.

25

Liu, Chi-hong, and 廖志航. "Time-dependent behaviour of concrete structures with special referenceto podium and frame structures." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2007. http://hub.hku.hk/bib/B38674245.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

26

Chin, Victor B. L. "The dynamic response of pile-soil interfaces during pile driving and dynamic testing events." Monash University, Dept. of Civil Engineering, 2003. http://arrow.monash.edu.au/hdl/1959.1/9421.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

27

Choi, Joonho. "Concurrent fire dynamic models and thermomechanical analysis of steel and concrete structures." Diss., Atlanta, Ga. : Georgia Institute of Technology, 2008. http://hdl.handle.net/1853/26679.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

28

Rios-Estepa, Rigoberto. "Unraveling the regulation of mint monoterpene biosynthesis development and experimental testing of kinetic mathematical models /." Pullman, Wash. : Washington State University, 2008. http://www.dissertations.wsu.edu/Dissertations/Fall2008/r_rios-estepa_111008.pdf.

Texto completo

Resumen

Thesis (Ph. D.)--Washington State University, December 2008.<br>Title from PDF title page (viewed on Jan. 15, 2009). "The Gene and Linda Voiland School of Chemical Engineering and Bioengineering." Includes bibliographical references.

Los estilos APA, Harvard, Vancouver, ISO, etc.

29

Craig, Bruce A. "Comparison of creep/duration of load performance in bending of Parallam® parallel strand lumber to machine stress rated lumber." Thesis, University of British Columbia, 1986. http://hdl.handle.net/2429/26194.

Texto completo

Resumen

A comparison of the creep/duration of load (DOL) performance of a new structural wood composite material called Parallam® parallel strand lumber (PSL) to two grades of machine-stress-rated (HSR) Douglas-fir lumber is presented in this thesis. Evaluation of the creep/DOL performance was made on nominal 2x4 members under constant bending stress at three stress levels. A total of 306 test specimens were evaluated for a 15-1/2 month time period. The analysis suggests that the duration of load effect for Parallam PSL was consistent with the Madison curve for the time period studied while the MSR Douglas-fir lumber was consistent with recent duration of load models developed for structural lumber. The analysis also indicates that the current duration of load adjustment factors can be applied to develop working stresses for Parallam. The creep behaviour of the Parallam PSL was found to be equivalent or better than the two MSR lumber grades under dry-service conditions. Furthermore, evidence of linear viscoelastic behaviour was found for all test materials within the range of applied stresses evaluated. Two mathematical models of creep were fitted to the creep data and compared. A '4-parameter linear viscoelastic' model fitted the creep data better than an empirical 'power curve' model. The model parameters developed provide a basis for estimating the mean creep behaviour and variability in creep response for these materials under in-service load conditions for dry-service environments.<br>Forestry, Faculty of<br>Graduate

Los estilos APA, Harvard, Vancouver, ISO, etc.

30

Ng, Pui-lam, and 吳沛林. "Constitutive modelling and finite element analysis of reinforced concrete structures." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2007. http://hub.hku.hk/bib/B3897566X.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

31

Wong, Chun-mei May, and 王春美. "The statistical tests on mean reversion properties in financial markets." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 1994. http://hub.hku.hk/bib/B31211975.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

32

Sidwall, Thygesen Signe, Astrid Berghult, and Camilla Öhman. "Prediction of elastic properties of nanofibrillated cellulose and microcrystalline cellulose : by mathematical models and tensile testing." Thesis, Uppsala universitet, Institutionen för teknikvetenskaper, 2012. http://urn.kb.se/resolve?urn=urn:nbn:se:uu:diva-177367.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

33

王偉洪 and Wai-hung Wong. "A study of constitutive models on engineering properties of Hong Kong marine clay." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 1997. http://hub.hku.hk/bib/B31214745.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

34

Wong, Man-kie, and 黃文基. "A study of capacity predictions for driven piles by dynamic pile testing." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2006. http://hub.hku.hk/bib/B37106120.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

35

Tan, Falong. "Projected adaptive-to-model tests for regression models." HKBU Institutional Repository, 2017. https://repository.hkbu.edu.hk/etd_oa/390.

Texto completo

Resumen

This thesis investigates Goodness-of-Fit tests for parametric regression models. With the help of sufficient dimension reduction techniques, we develop adaptive-to-model tests using projection in both the fixed dimension settings and the diverging dimension settings. The first part of the thesis develops a globally smoothing test in the fixed dimension settings for a parametric single index model. When the dimension p of covariates is larger than 1, existing empirical process-based tests either have non-tractable limiting null distributions or are not omnibus. To attack this problem, we propose a projected adaptive-to-model approach. If the null hypothesis is a parametric single index model, our method can fully utilize the dimension reduction structure under the null as if the regressors were one-dimensional. Then a martingale transformation proposed by Stute, Thies, and Zhu (1998) leads our test to be asymptotically distribution-free. Moreover, our test can automatically adapt to the underlying alternative models such that it can be omnibus and thus detect all alternative models departing from the null at the fastest possible convergence rate in hypothesis testing. A comparative simulation is conducted to check the performance of our test. We also apply our test to a self-noise mechanisms data set for illustration. The second part of the thesis proposes a globally smoothing test for parametric single-index models in the diverging dimension settings. In high dimensional data analysis, the dimension p of covariates is often large even though it may be still small compared with the sample size n. Thus we should regard p as a diverging number as n goes to infinity. With this in mind, we develop an adaptive-to-model empirical process as the basis of our test statistic, when the dimension p of covariates diverges to infinity as the sample size n tends to infinity. We also show that the martingale transformation proposed by Stute, Thies, and Zhu (1998) still work in the diverging dimension settings. The limiting distributions of the adaptive-to-model empirical process under both the null and the alternative are discussed in this new situation. Simulation examples are conducted to show the performance of this test when p grows with the sample size n. The last Chapter of the thesis considers the same problem as in the second part. Bierens's (1982) first constructed tests based on projection pursuit techniques and obtained an integrated conditional moment (ICM) test. We notice that Bierens's (1982) test performs very badly for large p, although it may be viewed as a globally smoothing test. With the help of sufficient dimension techniques, we propose an adaptive-to-model integrated conditional moment test for regression models in the diverging dimension setting. We also give the asymptotic properties of the new tests under both the null and alternative hypotheses in this new situation. When p grows with the sample size n, simulation studies show that our new tests perform much better than Bierens's (1982) original test.

Los estilos APA, Harvard, Vancouver, ISO, etc.

36

Zhu, Xuehu. "Model-adaptive tests for regressions." HKBU Institutional Repository, 2015. https://repository.hkbu.edu.hk/etd_oa/189.

Texto completo

Resumen

In this thesis, we firstly develop a model-adaptive checking method for partially parametric single-index models, which combines the advantages of both dimension reduction technique and global smoothing tests. Besides, we propose a dimension reduction-based model adaptive test of heteroscedasticity checks for nonparametric and semi-parametric regression models. Finally, to extend our testing approaches to nonparametric regressions with some restrictions, we consider significance testing under a nonparametric framework. In Chapter 2, “Model Checking for Partially Parametric Single-index Models: A Model-adaptive Approach", we consider the model checking problems for more general parametric models which include generalized linear models and generalized nonlinear models. We develop a model-adaptive dimension reduction test procedure by extending an existing directional test. Compared with traditional smoothing model checking methodologies, the procedure of this test not only avoids the curse of dimensionality but also is an omnibus test. The resulting test is omnibus adapting the null and alternative models to fully utilize the dimension-reduction structure under the null hypothesis and can detect fully nonparametric global alternatives, and local alternatives distinct from the null model at a convergence rate as close to square root of the sample size as possible. Finally, both Monte Carlo simulation studies and real data analysis are conducted to compare with existing tests and illustrate the finite sample performance of the new test. In Chapter 3,Heteroscedasticity Checks for Nonparametric and Semi-parametric Regression Model: A Dimension Reduction Approach", we consider heteroscedasticity checks for nonparametric and semi-parametric regression models. Existing local smoothing tests suffer severely from the curse of dimensionality even when the number of covariates is moderate because of use of nonparametric estimation. In this chapter, we propose a dimension reduction-based model adaptive test that behaves like a local smoothing test as if the number of covariates is equal to the number of their linear combinations in the mean regression function, in particular, equal to 1 when the mean function contains a single index. The test statistic is asymptotically normal under the null hypothesis such that critical values are easily determined. The finite sample performances of the test are examined by simulations and a real data analysis. In Chapter 4，Dimension Reduction-based Significance Testing in Nonparametric Regression", as nonparametric techniques need much less restrictive conditions than those required for parametric approaches, we consider to check nonparametric regressions with some restrictions under sufficient dimension reduction structure. A dimension-reduction-based model-adaptive test is proposed for significance of a subset of covariates in the context of a nonparametric regression model. Unlike existing local smoothing significance tests, the new test behaves like a local smoothing test as if the number of covariates is just that under the null hypothesis and it can detect local alternative hypotheses distinct from the null hypothesis at the rate that is only related to the number of covariates under the null hypothesis. Thus, the curse of dimensionality is largely alleviated when nonparametric estimation is inevitably required. In the cases where there are many insignificant covariates, the improvement of the new test is very significant over existing local smoothing tests on the significance level maintenance and power enhancement. Simulation studies and a real data analysis are conducted to examine the finite sample performance of the proposed test. Finally, we conclude the main results and discuss future research directions in Chapter 5. Keywords: Model checking; Partially parametric single-index models; Central mean subspace; Central subspace; Partial central subspace; Dimension reduction; Ridge-type eigenvalue ratio estimate; Model-adaption; Heteroscedasticity checks; Significance testing.

Los estilos APA, Harvard, Vancouver, ISO, etc.

37

Uliana, David A. "The effects of earthquake excitations on reticulated domes." Thesis, Virginia Tech, 1985. http://hdl.handle.net/10919/45667.

Texto completo

Resumen

<p>Comparisons were made on the behavior of two full-sized reticulated domes subjected to uniform static loads only and uniform static loads with earthquake excitations. Space truss elements were used in the dome models. The stiffness matrix of the space truss element allows for the nonlinear strain-displacement behavior and the stress-strain behavior of the material is modeled with a bilinear approximation. The nonlinear solution technique is the Newton-Raphson method while the direct integration technique is the Newmark- Beta method.</p> <p>The joint displacements for the static and the dynamic analyses were compared for both domes along with the axial stresses in all members. The percentage increases in the axial stresses of the dynamic analyses as compared to those of the static analyses were determined.</p> <p> The reticulated domes used in the study were found to bet capable of withstanding the earthquake excitations when subjected to various uniform loads without failure.</p><br>Master of Science

Los estilos APA, Harvard, Vancouver, ISO, etc.

38

Ngan, Yuk-tung Henry, and 顏旭東. "Motif-based method for patterned texture defect detection." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2008. http://hub.hku.hk/bib/B40203608.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

39

Conners, Terrance E. "The effect of moisture gradients on the stiffness and strength of yellow-poplar." Diss., Virginia Polytechnic Institute and State University, 1985. http://hdl.handle.net/10919/74713.

Texto completo

Resumen

Wood with a uniform moisture distribution is known to have different mechanical properties compared to wood with a non-uniform moisture distribution. Moisture gradients are likely to develop in full-size members tested in the In-Grade Testing Program and might therefore affect the test results. The purpose of this study was to mathematically model the effect of desorption moisture gradients on the stiffness and strength of yellow-poplar beams. An additional objective was to experimentally determine gradient effects in yellow-poplar beams. Three-dimensional finite-element modeling was employed and several subsidiary models were developed. Among these was a three-parameter segmented model for fitting digitized tension and compression stress-strain curves. Unlike previous models (such as the Ramberg-Osgood model), this model has a linear slope up to the point approximately corresponding to the proportional limit. A methodology was also devised whereby most hardwood and softwood elastic constants can be estimated at any moisture content. Data are required at one moisture content. Equilibrated uniaxial testing was conducted at four moisture contents to acquire data for the finite-element model. It was found that the longitudinal Young's moduli in tension and compression were approximately equal at 6% and 18% moisture content; the compression modulus was greater at 12%, but the tension modulus was greater for green specimens. Intersection points for tension and compression mechanical properties may be different. Tests of small clear yellow-poplar beams indicated that moisture gradients induced at 12% equilibrium moisture content had little effect on the modulus of rupture up to 19% average moisture content. At higher moisture contents, gradient-containing beams were significantly stronger than equilibrated beams when comparisons were made at identical moisture contents. Modulus of elasticity data exhibited a similar trend, although differences between equilibrated and non-equilibrated beams were observed below 19% moisture content. The finite-element program was moderately successful in predicting the effects of moisture gradients on the strength and stiffness of yellow-poplar beams. Computer time and storage constraints limited the accuracy of the solutions. Predicted trends were verified by the experimental data. Modeling of full-size lumber indicated that significant moisture gradients will likely influence the stiffness and strength of higher quality lumber.<br>Ph. D.

Los estilos APA, Harvard, Vancouver, ISO, etc.

40

Pearce, Annie R. "Sustainability and the built environment : a metric and process for prioritizing improvement opportunities." Diss., Georgia Institute of Technology, 1999. http://hdl.handle.net/1853/19611.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

41

Darmenov, Anton. "Developing and testing a coupled regional modeling system for establishing an integrated modeling and observational framework for dust aerosol." Diss., Atlanta, Ga. : Georgia Institute of Technology, 2009. http://hdl.handle.net/1853/28217.

Texto completo

Resumen

Thesis (M. S.)--Earth and Atmospheric Sciences, Georgia Institute of Technology, 2009.<br>Committee Chair: Sokolik, Irina; Committee Member: Curry, Judith; Committee Member: Kalashnikova, Olga; Committee Member: Nenes, Athanasios; Committee Member: Stieglitz, Marc.

Los estilos APA, Harvard, Vancouver, ISO, etc.

42

沈維祥 and Weixiang Shen. "Advanced battery capacity estimation approaches for electric vehicles." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2002. http://hub.hku.hk/bib/B31243575.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

43

Beller, Douglas K. "Alternate Computer Models of Fire Convection Phenomena for the Harvard Computer Fire Code." Digital WPI, 2000. https://digitalcommons.wpi.edu/etd-theses/892.

Texto completo

Resumen

"Alternate models for extended ceiling convection heat transfer and ceiling vent mass flow for use in the Harvard Computer fire Code are developed. These models differ from current subroutines in that they explicitly consider the ceiling jet resulting from the fire plume of a burning object. The Harvard Computer fire Code (CFC) was used to compare the alternate models against the models currently used in CFC at Worcester Polytechnic Institute and with other available data. The results indicate that convection heat transfer to the ceiling of the enclosure containing the fire may have been previously underestimated at times early in the fire. Also, the results of the ceiling vent model provide new insight into ceiling vent phenomena and how ceiling vents can be modeled given sufficient experimental data. this effort serves as a qualitative verification of the models as implemented; complete quantitative verification requires further experimentation. Recommendations are also included so that these alternate models may be enhanced further. "

Los estilos APA, Harvard, Vancouver, ISO, etc.

44

Dogan, Deniz. "Numerical optimization for mixed logit models and an application." Diss., Atlanta, Ga. : Georgia Institute of Technology, 2008. http://hdl.handle.net/1853/28190.

Texto completo

Resumen

Thesis (M. S.)--Industrial and Systems Engineering, Georgia Institute of Technology, 2008.<br>Committee Chair: Anton Kleywegt; Committee Co-Chair: Alexander Shapiro; Committee Member: Charles Rosa; Committee Member: Shabbir Ahmed; Committee Member: Sigrun Andradottir.

Los estilos APA, Harvard, Vancouver, ISO, etc.

45

Meurer, Thomas. "Wave propagation in hysteretic media." Thesis, Georgia Institute of Technology, 2000. http://hdl.handle.net/1853/19090.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

46

Jeyanayagam, Samuel S. "Engineering analysis of a Chinese-type anaerobic digester." Diss., Virginia Polytechnic Institute and State University, 1986. http://hdl.handle.net/10919/49800.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

47

Mutlu, Mehmet Basar. "Numerical Simulations Of Reinforced Concrete Frames Tested Using Pseudo-dynamic Method." Master's thesis, METU, 2012. http://etd.lib.metu.edu.tr/upload/12614460/index.pdf.

Texto completo

Resumen

Considering the deficiencies frequently observed in the existing reinforced concrete buildings, detailed assessment and rehabilitation must be conducted to avoid significant life and value loss in seismic zones. In this sense, performance based evaluation methods suggested in the regulations and codes must be examined and revised through experimental and analytical research to provide safe and economical rehabilitation solutions. In this study, seismic behavior of three reinforced concrete frames built and tested in Middle East Technical University Structural Mechanics Laboratory is examined. The specimens are extracted from a typical interior frame of 3-story 3-bay reinforced concrete structure. One of the specimens has compliant design according to Turkish Earthquake Code (2007) and each of the other two specimens represents different types of deficiencies in terms of material strength and detailing. The test specimens were modeled using different modeling approaches and nonlinear dynamic analyses were conducted on the numerical models. Results of continuous pseudo-dynamic testing of three ground motions are presented and compared with the numerical simulations on models. Calibrated finite element models were used for evaluation of performance assessment procedure of Turkish Earthquake Code (2007) and further investigation on local deformation components in light of experimental findings and observations. Deformation sources of columns and joints were studied in terms of their interaction and contributions to the total drift. Estimated plastic hinge lengths of columns were compared with the experimental observations and the proposed expressions in the literature.

Los estilos APA, Harvard, Vancouver, ISO, etc.

48

Kim, Hoan-Kee. "Multi-scale nonlinear constitutive models using artificial neural networks." Diss., Atlanta, Ga. : Georgia Institute of Technology, 2008. http://hdl.handle.net/1853/22613.

Texto completo

Resumen

Thesis (Ph. D.)--Civil and Environmental Engineering, Georgia Institute of Technology, 2008.<br>Committee Chair: Rami M Haj-Ali; Committee Member: Arash Yavari; Committee Member: Donald W. White; Committee Member: Erian Armanios; Committee Member: Kenneth M. Will.

Los estilos APA, Harvard, Vancouver, ISO, etc.

49

Jain, S. K. "Analysis of the pressuremeter test by FEM formulation of the elasto-plastic consolidation." Diss., Virginia Polytechnic Institute and State University, 1985. http://hdl.handle.net/10919/53881.

Texto completo

Resumen

A decade has passed since the development of the self-boring pressuremeter (SBPM). Even though the device has been recognized by the geotechnical engineering profession as having high promise for evaluating in-situ stress-strain behavior of soils, its use is limited. In large part, this is due to the fact that there are important unanswered questions about the SBPM test. One of the major issues concerns the influence of drainage in the soil as it is sheared. In clays, the test is assumed to be undrained, but there is no way to control this other than by the rate of loading and no method has been put forth heretofore to define the required rate. This dissertation addresses the drainage issue by applying a numerical model capable of simulating the pressuremeter test under variety of conditions. To develop parameters for the soil model, a comprehensive laboratory testing effort was needed. The validity of the numerical model and the soil parameters is established by comparing it to SBPM tests performed in the field. The numerical model uses the finite element method in a special code capable of handling large strains, consolidation effects, and nonlinear soil behavior. Particular attention is addressed to the issue of pore pressure development and its dissipation. Relative influences of important soil parameters such as the permeability are checked against various rates of loading in the SBPM test. The results demonstrate that drainage likely occurs in most cases using conventional test procedures, and that this, in turn, leads to an error in interpretation of SBPM data. Based on the findings in the analyses, a procedure is proposed which should lead to a more rational method of performing the SBPM test where nearly undrained conditions are desired.<br>Ph. D.

Los estilos APA, Harvard, Vancouver, ISO, etc.

50

Wu, Y. F. (Yu-Fei). "Seismic retrofitting of rectangular reinforced concrete columns with partial interaction plating." 2002. http://web4.library.adelaide.edu.au/theses/09PH/09phw9591.pdf.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

Ofrecemos descuentos en todos los planes premium para autores cuyas obras están incluidas en selecciones literarias temáticas. ¡Contáctenos para obtener un código promocional único!