Tesis sobre el tema "Isotherme Kalorimetrie"

The concept of a self-incompatible solvent is introduced as a molecule composed of two parts (compound 1 and 2) with unfavourable interactions. A third compound will be readily dissolved in this solvent to diminish this unfavourable interaction by dilution. The more incompatible compounds 1 and 2 are, the stronger this behaviour is expected to be. In this work, ionic liquids comprising non-polar carbon chain and polar ionic group are chosen to serve as a model of self-incompatible solvent. The interactions parameters k of the ionic liquids with active ingredients are investigated to examine the effect of self-incompatibility of the ionic liquid molecule. On the other hand, phase separation between compounds 1 and 2 will reduce the positive effect of self-incompatibility. The tendency of phase separation is increasing with increasing size of the two compounds. Thus, if compounds 1 and 2 are blocks tied together into a block copolymer, one expects a decreasing ability of the block copolymer to dissolve an active ingredient with increasing block length. In this work the ability of polybutadiene-block-poly(2-vinylpyridine) (PB-b-P2VP) block copolymers to dissolve the model compound anthracene is investigated. As expected, the solubility indeed decreases with increasing block length.

Self-heating in storage facilities of biomass pellet can lead to spontaneous combustion. This has resulted in many fires over the years, causing both financial and environmental losses. In order to assess the risk for spontaneous combustion of biomass pellets during storage, it is important to know how prone the fuel is to self-heating, i.e. to determine its reactivity. This thesis presents experimental work performed to develop a sensitive screening test procedure for biomass pellets, using isothermal calorimetry for direct measurement of the heat production rate. This method can be used to compare the reactivity of different biomass pellets. This could be useful for e.g. facility owners to gain better knowledge of their fuels propensity for self-heating and thereby facilitate safer storage. The screening test procedure can also be used for research purposes. Experiments have been performed with 31 different biomass pellet batches to investigate how the pellet composition, origin, etc. influence the reactivity of the pellets. The results from these experiments clearly show a significant difference in reactivity between different types of pellets. The results indicate that pine/spruce mix pellets are significantly more reactive than all other types of pellets tested, and that pellets consisting of 100 % pine are more reactive than pellets consisting of 100 % spruce. Pellets produced from winery wastes, straw, or eucalyptus, have low reactivity compared to pellets consisting of pine and/or spruce. The reactivity of the pellets was shown to be reduced by either introducing certain types of anti-oxidants into the pellets or by extracting lipids from the raw material of pellets. The screening test procedure is already being used today by some facility owners for assessing their fuels propensity for self-heating. The procedure is also one of the suggested test methods in “ISO/CD 20049 Solid biofuels — Determination of self-heating of pelletized biofuels”.
This thesis presents experimental work performed to develop a sensitive screening test procedure for biomass pellets, using isothermal calorimetry for direct measurement of the heat production rate. This method can be used to directly compare the reactivity, that is how prone the fuel is to self-heating, of different batches of biomass pellets. The results could be used for safety assessment by the industry or for research purposes to investigate how different factors influence the self-heating potential. Experiments were performed with 31 different biomass pellet batches to investigate how the pellet composition, origin, etc. influence the heat release rate. The results clearly show that there is a significant difference in reactivity between different types of pellets. Pine/spruce mix pellets are more reactive than the other types of pellets tested and pellets consisting of 100 % pine are more reactive than pellets consisting of 100 % spruce. Pellets produced from winery wastes, straw, or eucalyptus, have low reactivity compared to pellets consisting of pine and/or spruce. The results also show that the reactivity of the pellets can be reduced by either introducing certain types of anti-oxidants into the pellets or by extracting lipids from the raw material of pellets.

The study of protein and surfactant interactions is of great significance in a number of applications, such as the cosmetic, food or pharmaceutical industries and many others. However, they require further study due to their compositional complexity and the limitations of current analytical approaches. In this thesis, the cationic surfactant septonex in combination with two differently charged proteins lysozyme and bovine serum albumin under different physiological conditions (temperature, surfactant concentration, environment and others) was selected to study the interactions. Characterization of protein-surfactant interactions is a very important but challenging task, therefore it is essential to use appropriate approaches to explore the nature of these interactions. In order to unify the information to provide rational models, calorimetric methods (DSC, ITC) and dynamic light scattering were used. Isothermal titration calorimetry monitors the evidence for the formation of the system of the mentioned substances and information on aggregation behavior, differential scanning calorimetry characterizes the thermal stability of proteins and dynamic light scattering made it possible to monitor changes in particle size. Both proteins have been proven to interact with positive septonex, even if the lysozyme molecule is also positively charged. However, significant differences were found between the two proteins. From the obtained results it is evident that the identical charge of the protein with the surfactant has an effect on the intensity of the measurement, although all measured interactions showed an endothermic character.

This master thesis deals with the study of thermodynamic and structural aspects of the interactions of humic acids with organic ions. Methylene blue (dye) was used as a model organic ion. The interactions were studied by isothermal titration calorimetry, dissolution calorimetry and by diffusion in diffusion cells.

Vliv hyaluronanu na micelizaci tenzidů byl studován různými fyzikálně-chemickými metodami. Byly zvoleny dva kationaktivní tenzidy, a to tetradecyltrimethylammonium bromid (TTAB) a cetyltrimethylammonium bromid (CTAB). Metoda izotermické titrační kalorimetrie byla využita pro stanovení entalpie micelizace, tenziometrie popisuje povrchové vlastnosti daných vzorků. Byl sledován také vliv různé molekulové hmotnosti použitého hyaluronanu a délka alkylového řetězce tenzidu na agregační chování daného systému. Výsledkem jsou hodnoty kritické micelární nebo agregační koncentrace tenzidu. V neposlední řadě se diskutuje využití agregátů hyaluronan-tenzid jako možné nosiče pro cílenou distribuci léčiv.

The presented diploma thesis deals with the study of interactions between humic acids as the main component of soil organic matter with a model organic pollutant presented by cationic surfactant Septonex (which was expected to interact positively with humic acids due to its charge) through unconventional combination of dialysis and diffusion techniques realized in diffusion cells together with isothermal titration calorimetry capable of elucidating the nature of ongoing reactions from a thermodynamic point of view. The experiments were performed with a humic acid isolated by standard isolation procedure from Leonardite (1S104H) purchased from the International Society for Humic Substances, with humic acids isolated from lignite as well as modal chernozem. The aim of the submited diploma thesis is to assess the influence of carboxyl functional groups in the structure of humic acids to interactions with Septonex. For this reason, said samples of humic acids have been modified by selective methylation of their carboxyl functional groups, which can no longer participate in interactions with ionic substances. Results from diffusion cells and isothermal titration calorimetry confirmed the assumption that Septonex interacted with all types of unmodified humic acids more than with their methylated derivatives. Despite the available literature, it was surprising that the differences in the interaction of humic acids with Septonex were not diametrically different when comparing unmodified humic acids with their methylated derivatives. The extent of these interactions was assessed through the apparent equilibrium constant Kapp determined in the diffusion (dialysis) experiments and from the course of enthalpy curves from isothermal titration calorimetry. After the experiments and their evaluation, it can be concluded that humic acids and Septonex in their interactions, due to their structures, probably apply not only electrostatic interactions, especially through available carboxyl functional groups of humic acids and positively charged hydrophilic parts of Septonex molecules, but also a significant role have a hydrophobic effect, hydrogen bonds and Van der Waals forces.

The main object of the diploma thesis is study of interaction beetween humic acids and selected metal ions using calorimetric titration. The research about reactivity of humic substances is done comparing the different models used to describe the variety of properties of humic substances. In experimental part the methods of FT-IR spektrometry, potenciometric and conductometric titration are used to recieve the total acidity and carboxylic acidity of lignite humic acid. The optimalization of isothermic titration calorimetry is done to be used within study of reactivity of humic acids, revealing the best correlation with sols of studied humic acid. The basic organic compounds were used including benzoic acid, ftalic acid, salycilic acid, pyrocatechol and phenol as models of bonding groups in humic acids. The reaction enthalpy was calculated from the titration of models and results were compared with semiempiric quantum chemistry calculations following INDO method.

This diploma thesis deals with study of crystalline structure of polyhydroxybutyrate (PHB), which contains different types of additives for studying of their nucleation activity and which were prepared by mixing. It is about boronitrid (BN), sacharin, hydroxapatit, plasticizer Tegmer a tree types of talc. Crystal structure was analysed by differential scanning calorimetry and x-ray diffraction, supramolecular structure was observed by optical microscopy (polarized and confocal laser scanning). Nucleating activity was evaluated by isothermal and non-isothermal crystallization made on calorimeter and heated table of optical microscope. There is not influence of additives on crystallographic structure, but additives affects number and size of spherulites including crystal domains defects, which can have impact on final mechanical properties. BN and talcs react as nucleating agents, other additives during low and high cooling speeds (vc) inhibit nucleation and in middle cooling speeds are without effect. Nucleating activity is not evaluated by numerically, because decrease of crystallization temperature together with vc is not linear. Results of direct methods are based on picture analysis, which is great benefit for understanding of crystal behaviour of PHB.

At present, soils face great threats. Consequences of human activities, such as climate change, acidification and contamination result in decreased soil health. This is a threat to human health and well-being, since our society is dependent on soil ecosystem services. The soil ecosystems provide resources, such as food and fresh water, regulate the climate and play key parts in important life supporting biological processes, e.g. cycling of carbon and nutrients. Due to increased awareness of the threats that soils face, and its importance to humans, soil quality monitoring has recently received increased attention. Microorganisms run most biological processes in the soil, such as decomposition of organic material and nutrient cycling. Thus, microbial activity and diversity are considered useful biological indicators for soil quality monitoring. These biological properties can be examined using different methods. The aim of the project was to evaluate the potential of multiple substrate-induced respiration (MSIR), using the MicroRespTM system, and isothermal calorimetry for determining microbial activity and diversity in soils contaminated with copper (Cu) and polycyclic aromatic hydrocarbons (PAH). Thereby, the methods’ applicability in risk assessment of contaminated soil could be decided. MSIR is considered appropriate for determining microbial activity and functional diversity, while isothermal calorimetry has not been tested as much in this area. The calorespirometric ratio (produced heat per unit CO2) was calculated to evaluate potential relationships between heat and CO2 at different contamination levels. Although there was some variation between the methods, Cu had a clear effect on both microbial activity and functional diversity. Both methods were thus considered applicable in risk assessment of soil contaminated with Cu. The impact of PAH appeared to be more complex, the effects on microbial activity varied and PAH had little significant effect on functional diversity. Neither of the methods were therefore considered applicable for assessment of soil contaminated with PAH. The calorespirometric ratio did not provide useful results, and cannot be recommended for risk assessment purposes at present.
I dagsläget utsätts marken för stora hot. Följder av mänsklig aktivitet, så som klimatförändringar, försurning och förorening försämrar markens kvalitet. Detta är ett hot mot människors hälsa och välmående, eftersom vårt samhälle är beroende av markens ekosystemtjänster. Markens ekosystem förser oss med exempelvis mat och rent vatten, reglerar klimatet, och har nyckelroller i viktiga biologiska processer, exempelvis cirkulering av kol och näringsämnen. På grund av ökad medvetenhet om hoten mot marken samt dess betydelse för människan, har kontroll av markens kvalitet börjat få ökad uppmärksamhet. Mikroorganismer sköter de flesta biologiska processer som sker i marken, så som nedbrytning av organiskt material och cirkulering av näringsämnen. Därmed anses mikrobiell aktivitet och diversitet vara lämpliga biologiska indikatorer vid kontroll av markens kvalitet. Dessa biologiska egenskaper kan mätas med flera olika metoder. Syftet med projektet var att utvärdera potentialen i att använda multipla substrat-inducerad respiration (MSIR), genom att använda systemet MicroRespTM, samt isotermisk kalorimetri för att mäta mikrobiell aktivitet och funktionell diversitet i mark förorenad med koppar (Cu) och polycykliska aromatiska kolväten (PAH). Därmed kunde metodernas tillämplighet i riskbedömning av förorenad mark bestämmas. MSIR anses vara en lämplig metod i syfte att undersöka mikrobiell aktivitet och funktionell diversitet, medan isotermisk kalorimetri inte är lika beprövat. Kvoten mellan värmeproduktion och respirerad CO2, the calorespirometric ratio, beräknades för att utvärdera eventuella samband mellan värmeproduktion och respiration vid olika föroreningskoncentrationer. Trots att det förekom viss variation mellan metoderna, hade Cu en tydlig effekt på både mikrobiell aktivitet och funktionell diversitet. Båda metoder ansågs därför vara tillämpbara i riskbedömning av Cu-förorenad jord. PAH hade varierande effekt på mikrobiell aktivitet och liten signifikant effekt på funktionell diversitet. Ingen av metoderna ansågs därför tillämpbar i riskbedömning av jord förorenad med PAH. The calorespirometric ratio tillhandahöll ej användbara resultat, och kunde därmed inte rekommenderas i riskbedömningssyfte.

This thesis is focused at possibilities of preparation and characterization of XRD-amorphous delaminated and dehydroxylated talc phase – meta-talc, which can have its potential application and a starter material for a preparation of magnesium-silicate analogues of geopolymers. Changes in structure and morphology of talc ore were observed during this work. For the purposes of this research, two various talc ores – chloritic and dolomitic were examined. Whole process of meta-talc preparation was examined with whole scale of instrumental techniques such as X-ray diffraction, simultaneous thermogravimetric a differential thermal analysis, infrared spectroscopy, scanning electron microscopy or laser analysis of particle size. Meta-talc can be obtained via mechanochemical activation of talc ore with subsequent calcination. Mechanochemical treatment lead to destruction of original crystal structure and breaking of original bonds, i.e. the product of this treatment was almost amorphous and delaminated. Most of hydroxyl groups were converted to molecules of water which remained adsorbed or coordinated in ore structure. These molecules were removed during calcination step.

This master thesis deals with study of chitosan-lignohumate, chitosan-polystyrenesulfonate, chitosan-alginate and chitosan-carrageenan polyelectrolyte complexes. The work was motivated by research of finding suitable alternative substance for lignohumate. The molecular weights of substances were characterized using SEC-MALLS. A degree and a character of the interactions between polyelectrolyte were studied by isothermal titration calorimetry and dynamic light scattering method. The calorimetric experiments proved that decreasing concentration of samples causes decreasing of heat flow. The best calorimetric measurements were provided by adding chitosan into polymer solution. The interactions between chitosan and polyanions and influence of mixing order were proved also by measuring intensity of zeta potential, Z-average of particle size and turbidity. New chitosan-based materials have a big potential in agriculture and medicine.

This work focuses on the hydration of four calcium aluminate phases – C3A, C12A7, CA and CA2. Above all, the influence of particle size and method of preparation on hydration behaviour were studied. Influence of these factors on hydration products were also investigated. Calcium aluminates were prepared by solid state synthesis and amorphous citrate method. Both methods were described in detail. The particle size was determined by laser diffraction. Isothermic calorimetry was used to investigate the process of hydration. Hydration products were identified by X-ray diffraction analysis and simultaneous thermogravimetric and differential thermal analysis.

Biopolymer surfactant systems have been studied by using different physico chemical methods. As the biopolymer, it was chosen high (1400–1600 kDa), medium (250–450 kDa) and low (8–15 kDa) molecular weight sodium hyaluronate. Two cationic surfactants – cetyltrimethylammonium bromide (CTAB) and carbethopendecinium bromide (Septonex) were selected to provide polyelectrolyte complexes with oppositely charged hyaluronan. The critical aggregation concentration of the surfactant in the system was monitored by dynamic light scattering (Zetasizer Nano ZS). SEC-MALS method was used for the description of the conformation of sodium hyaluronate of different molecular weights and polyelectrolytes complexes hyaluronan surfactant after reaching the aggregation point. Isothermal titration calorimetry (ITC) was used to determine the critical aggregation concentration of the surfactant by monitoring the thermal changes accompanying the aggregation of the system. It was found out that the increasing molecular weight of hyaluronan in these systems decreases the critical aggregation concentrations and conversely.

The theme of this work is to monitor the effect of zinc on the properties of blended Portland cements. Zinc was tested in the form of two-soluble salts: Zn(NO3)22 H2O and ZnCl2 and a very slightly soluble compound ZnO. Blended cements were prepared by partial replacement with finely ground granulated blast furnace slag, high-temperature and fluidized bed combustion filter fly ash. Flow properties were studied on the prepared pastes. Impact on hydration reactions was examined by using of isothermal and isoperibolic calorimetry. Flexural and compressive strength were measured as mechanical properties of the prepared test specimens. The phase composition of the prepared composites and incorporation of zinc ions in the cement matrix via leaching tests and FTIR analyzes were also studied. Microstructure development of cement samples was tested by SEM analysis with EDS. Influence on ecotoxicity was also measured.

The influence of seven additives on the crystallization ability of polylactide (PLA), melt flow index (MVR) and mechanical tensile properties was studied. Pressed plates with a thickness of 0.8 mm were tested. Selected additives added in amounts of 0.5 and 1.0% were as follows: talc, sodium benzoate, mixtures of organic salts with amorphous SiO2 and zinc stearate, metal salt, phosphate salt, and potassium salt of 5-dimethylsulfoisophthalate (LAK-301 - nucleating agent developed for PLA). Non-isothermal crystallization measurements were performed at different cooling rates (0.3; 0.5; 0.7; 1.0 and 1.5 ° C). All nucleation agents increased the MVR of PLA except talc; the largest increase (9-fold and 24-fold) was the addition of metal salt. The additives did not fundamentally change the mechanical properties. All samples were rather brittle (the most brittle with LAK-301), the modulus of elasticity was around 1.2 GPa for all samples, the strength of PLA was increased the most by the addition of 1% talc (by 12%) and the elongation at break was increased by organic salt with SiO2. All samples with nucleating agents content of 1% were amorphous (crystalline content did not exceed 2%). Thus, the addition of reagents did not support the crystallization process during rapid cooling, even in the case of LAK-301. However, LAK-301 was acting as an excellent nucleating agent at slow cooling rates (1.5 °C / min and below). The nucleation activity of the additives decreased in the following order: LAK-301, organic salt with zinc stearate, talc, organic salt modified with amorphous SiO2 and phosphate salt. Samples with sodium benzoate and metal salt were crystallizing on cooling in several steps and it was not possible to use the method of Dobrev and Gutzow to evaluate the nucleation activity.

The aim of submitted diploma thesis is the study of non-isothermal crystallization kinetics of polylactide (PLA) with selected agents (1 %) and observation of the emerging crystalline structure under polarizing optical microscope. The agents were talc, a mixture of organic salts with the addition of amorphous SiO2 (HPN 68L) and zinc stearate (HPN 20E) and LAK-301 (potassium salt of 5-dimethylsulfoisophtalate), which is a nucleating agent developer for PLA. The PLA matrix served as a reference. Non-isothermal crystallization took place on a differential scanning calorimeter at cooling rates () 0,3; 0,5; 0,7; 1; 1,5; 2 °C/min After non-isothermal crystallization, the crystalline fraction (Xc) od PLA was evaluated from X-ray diffraction analysis, and the supramolecular structure was observed after chemical degradative etching using confocal laser scanning microscope. The crystallization kinetics were evaluated by the methods of Jeziorny and Mo and the activation energy of the crystallization was determined according to the Friedmann method. All prepared materials were amorphous (Xc 40 % for up to 1,5 °C/min). However, for LAK-301, Xc decreased to 30 % already at the = 2 °C/min and it can be assumed that with increasing its nucleation activity will decrease. A spherulitic structure was observed in all samples, but the number and size of spherulites decreased with increasing and the appearance varied according to the type of agent. Both kinetic models proved to be unsuitable for materials with low Xc and the highest because the rate of crystallization did not change. With the Jeziorny method, it was possible to evaluate the kinetics only for the relative crystallinity Xt = 29–50 % and with the Mo method it was not possible to evaluate the data for the highest for PLA matrix and sample with HPN 68L. The samples with LAK-301 and HPN 68L showed the lowest activation energy.

Thermoplastische Kunststoffe (sog. Thermoplaste) lassen sich in einem be-stimmten Temperaturbereich beliebig oft schmelzen und in einer gewünschten Form erstarren. Grundvoraussetzung für eine bestimmte Anwendung eines thermoplastischen Bauteils sind die Gebrauchseigenschaften des Materials, die im Wesentlichen vom Ablauf der Erstarrung abhängen. Die Moleküle einiger Thermoplaste können bei der Erstarrung geordnete kristalline Bereiche bilden. Dies sind die sog. teilkristallinen Kunststoffe, deren Erstarrungsprozess Kristallisation genannt wird. Die dabei entstehenden Kristallstrukturen werden zusammen mit deren Charakteristiken allgemein als Morphologie der teilkristallinen Kunststoffe bezeichnet. Die Morphologie hat einen signifikanten Einfluss auf die mechanischen, thermischen und optischen Eigenschaften des Materials. Dementsprechend stellen Kenntnisse über die Kristallisation eine wertvolle Hilfe bei der Vorhersage der Gebrauchseigenschaften eines teilkristallinen Kunststoffs dar. Um die Kristallisation zu starten, muss zunächst eine Energiebarriere überwunden werden, die an erster Stelle vom molekularen Aufbau des Kunststoffs abhängt. Somit weisen beispielsweise Kunststoffe mit linearen, regelmäßigen Molekülen und kleinen Seitengruppen eine niedrigere Energiebarriere und aus diesem Grund eine starke Neigung zur Kristallisation auf. Einige Zusatzstoffe wie z. B. unterschiedliche Additive, Farbstoffe oder Füllstoffe können die Energiebarriere und infolgedessen die Kristallisation eines teilkristallinen Kunststoffs wesentlich beeinflussen. Das Ziel dieser Dissertation war es, ein bestehendes Kristallisationsmodell zu erweitern und es an gefüllte oder additivmodifizierte teilkristalline Kunststoffe anzupassen. Das erweiterte Modell soll die Ermittlung eines Kristallisationspa-rameters, des sog. Keimbildungsexponenten, eines gefüllten oder additivmodifizierten teilkristallinen Kunststoffs bei der nicht-isothermen Kristallisation ermöglichen. Der Keimbildungsexponent ist mit der erwähnten Energiebarriere eng verbunden und bestimmt somit den Ablauf des Kristallisationsprozesses bzw. die daraus folgende Morphologie. Ein wesentlicher Schwerpunkt der Arbeit lag darin, die vorgeschlagene Modellerweiterung bei verschiedenen Abkühlgeschwindigkeiten zu überprüfen. Im Anschluss sollten die Beziehungen zwischen den berechneten Keimbildungsexponenten und experimentell ermittelten me-chanischen Eigenschaften (E-Modul, Streckspannung und Schlagzähigkeit) überprüft werden. Für die Untersuchungen wurden drei verschiedene Polymersysteme verwendet: PP / Talkum, HDPE / Talkum sowie PA6 / Bentonit. Hierbei weist der Füllstoff eine stark positive, schwach positive bzw. inhibierende Wirkung auf die Kristallisation der entsprechenden Polymermatrix auf. Hinsichtlich reiner Polymere wurde eine gute Übereinstimmung zwischen den ermittelten und Literaturwerten des Keimbildungsexponenten festgestellt. Die Zugabe von positiv wirkendem Talkum in PP bzw. HDPE führt zu einer Abnah-me des Keimbildungsexponenten, was zu dickeren Kristallen des jeweiligen Kunststoffs führte. Im Gegensatz dazu bewirkte die Bentonitzugabe einen zu-nehmenden Keimbildungsexponenten, was anschließend dünnere PA6-Kristalle zur Folge hat. Die durchgeführten Untersuchungen zeigen außerdem, dass die Füllstoffpartikelgröße einen ausgeprägten Einfluss auf den ermittelten Keimbildungsexponenten hat. Weiterhin wurde festgestellt, dass der ermittelte Keimbildungsexponent durch die (DSC)-Abkühlgeschwindigkeit beeinflusst wird. Es wurde ferner gezeigt, dass sich dieser Einfluss ab einer bestimmten Abkühlgeschwindigkeit (20 K/min im Falle des PP und HDPE bzw. 15 K/min im Falle des PA6) nicht mehr ändert, was zu einem konstanten Keimbildungsexponenten führt. Um den Einfluss der Abkühlgeschwindigkeit auf die modellierte Größe zu berücksichtigen, sind weitere Untersuchungen nötig. Die Ergebnisse der Arbeit zeigen weiterhin, dass der berechnete Keimbildungsexponent mit den experimentell ermittelten Werten für E-Modul, Streckspannung und Charpy-Schlagzähigkeit bei talkumgefülltem PP gut korreliert. Solche Korrelationen wurden jedoch bei den HDPE- und PA6-Proben nicht gefunden. Der Grund hierfür könnte eine ausgeprägte Orientierung der HDPE-Makromoleküle bzw. ein starker mikromechanischer Effekt des exfolierten Bentonits sein. Diese Effekte konnten im Rahmen der Arbeiten bestätigt werden. Die in dieser Arbeit erzielten Ergebnisse zeigen, dass die vorgeschlagene Mo-dellerweiterung auch bei gefüllten oder additivmodifizierten Kunststoffen zufriedenstellende Resultate liefert. Die entsprechende Berechnung erfordert dabei lediglich eine DSC-Messung, was im Vergleich zum Stand der Technik in einen niedrigeren Messaufwand resultiert. Die vorliegende Arbeit liefert daher einen signifikanten Beitrag zur Erstellung des Zusammenhangs zwischen der Kristallisation, der Morphologie und dem mechanischen Verhalten von teilkristallinen Polymeren
Thermosoftening polymers, also called thermoplastics, can be repeatedly melt-ed and solidified into a desired shape in a certain temperature range. The basic requirements for a particular application of a thermoplastic component are its functional characteristics, which significantly depend on the solidification pro-cess. The molecules of some thermoplastics can form ordered crystalline regions during the solidification process. These are so-called semi-crystalline polymers, whose solidification process is called crystallization. The resulting crystal struc-ture elements, together with their properties, are commonly referred to as the morphology of semi-crystalline polymers. The morphology has a significant in-fluence on the mechanical, thermal and optical properties of the material. Ac-cordingly, knowledge about the crystallization is a valuable aid in predicting the final properties of a semi-crystalline polymer. In order for the crystallization to start, it is necessary for an activation energy barrier to be overcome. The activation energy barrier depends on the molecular structure of the polymer. Polymers with linear, regular molecules and small side groups possess a low activation energy barrier and therefore crystallize most easily. Some ingredients, such as various additives, pigments or fillers, can significantly affect the energy barrier and consequently the crystallization of a semi-crystalline polymer. The aim of this thesis was to extend an existing crystallization model and adapt it to filled or additive-modified semi-crystalline polymers. The extended model should allow the determination of a crystallization parameter, the so-called nu-cleation parameter of filled or additive-modified semi-crystalline polymers during non-isothermal crystallization. The nucleation parameter is closely connected with the activation energy barrier and thus determines the crystallization process and consequentially the resulting morphology. An important task in this work was to verify the proposed model extension for different cooling rates. In addition, the correlations of the calculated nucleation parameter with experimentally determined mechanical properties (Young’s modulus, yield stress and impact strength) are established and discussed. In this research, three different polymer systems were used: PP / talc, HDPE / talc and PA6 / bentonite. In these three materials, the filler has a strong positive, a weak (positive) and a negative influence on the crystallization of a given polymer, respectively. A good agreement between the values of the nucleation parameter determined in this work and those found in literature was obtained as regards pure poly-mers. The addition of positive-acting talc in PP and HDPE leads to a decreased nucleation parameter, resulting in an increase of the crystal thickness of PP and HDPE. By contrast, the addition of bentonite increases the nucleation parameter of PA6 and therefore leads to a decrease in the crystal thickness of PA6. It was also shown that the filler particle size has a significant influence on the nucleation parameter. Furthermore, it was shown that the DSC cooling rate up to a certain value (20 K/min as regards PP und HDPE i.e. 15 K/min regarding PA6) has an influence on the determined nucleation parameter. Afterwards, the nucleation parameter reaches a plateau and shows no further changes with the cooling rate. To be able to add the influence of the cooling rate into the model, further studies are needed. Furthermore, it was shown that the obtained nucleation parameters correlates well with the Young modulus, yield stress and impact strength as regards PP filled with talc. In contrast to PP, such correlations were not found for HDPE and PA6 samples. The possible reason for the absence of correlations could be the orientation of the HDPE molecules, i.e. the strong reinforcing effects of the intercalated bentonite in PA6. These effects were confirmed in the scope of the work. The results obtained in this work show that the proposed model extension is applicable as regards filled semi-crystalline polymers. In comparison to the state of the art, the proposed model extension requires only a single DSC-measurement resulting in a lower measuring expenditure. Therefore, the pre-sent work provides a significant contribution to establishing the mathematical relationship between the crystallization, morphology and the mechanical behavior of semi-crystalline polymers

The concept of a self-incompatible solvent is introduced as a molecule composed of two parts (compound 1 and 2) with unfavourable interactions. A third compound will be readily dissolved in this solvent to diminish this unfavourable interaction by dilution. The more incompatible compounds 1 and 2 are, the stronger this behaviour is expected to be. In this work, ionic liquids comprising non-polar carbon chain and polar ionic group are chosen to serve as a model of self-incompatible solvent. The interactions parameters k of the ionic liquids with active ingredients are investigated to examine the effect of self-incompatibility of the ionic liquid molecule. On the other hand, phase separation between compounds 1 and 2 will reduce the positive effect of self-incompatibility. The tendency of phase separation is increasing with increasing size of the two compounds. Thus, if compounds 1 and 2 are blocks tied together into a block copolymer, one expects a decreasing ability of the block copolymer to dissolve an active ingredient with increasing block length. In this work the ability of polybutadiene-block-poly(2-vinylpyridine) (PB-b-P2VP) block copolymers to dissolve the model compound anthracene is investigated. As expected, the solubility indeed decreases with increasing block length.

Title: Self-assembly of polymers with amphiphilic compounds (surfactants) in aqueous solutions Abstract: This PhD Thesis is devoted to the co-assembly in systems containing electrically charged polymers (polyelectrolytes and block copolymers containing polyelectrolyte sequences). I studied the interactions between block copolymers and oppositely charged surfactants in aqueous solutions, and the structure and properties of co-assembled nanoparticles by a combination of several experimental methods. I found that the spontaneous formation, solubility and stability of complex nanoparticles depend not only on the electrostatic attractive forces but also on the hydrophobic effects. In a major part of my Thesis, I studied the interaction of polyelectrolytes with oppositely charged gemini surfactants (containing two charged head-groups interconnected by a short linker and two hydrophobic tails) which is a relatively new topic - much less studied than the co-assembly with conventional single tail surfactants. Better understanding of the formation and properties of complexes containing gemini surfactants and polymers provides knowledge that should lead to novel tailor-made nanoparticles with desired properties for applications in medicine and new technologies (including nano-technologies). We have shown that the...