Acceder

Bibliografías temáticas / Joints / Tesis

Siga este enlace para ver otros tipos de publicaciones sobre el tema: Joints.

Tesis sobre el tema "Joints"

Autor: Grafiati

Publicado: 4 de junio de 2021

Última modificación: 25 de julio de 2025

Crea una cita precisa en los estilos APA, MLA, Chicago, Harvard y otros

Elija tipo de fuente:

Consulte los 50 mejores tesis para su investigación sobre el tema "Joints".

Junto a cada fuente en la lista de referencias hay un botón "Agregar a la bibliografía". Pulsa este botón, y generaremos automáticamente la referencia bibliográfica para la obra elegida en el estilo de cita que necesites: APA, MLA, Harvard, Vancouver, Chicago, etc.

También puede descargar el texto completo de la publicación académica en formato pdf y leer en línea su resumen siempre que esté disponible en los metadatos.

Explore tesis sobre una amplia variedad de disciplinas y organice su bibliografía correctamente.

1

ath, Shrikant Sainath Shrikant. "Joint contact modelling of articular cartilage in synovial joints." Thesis, University of Leeds, 2010. http://etheses.whiterose.ac.uk/1025/.

Texto completo

Resumen

Hip joint is one of the important load bearing joints and has been extensively studied to investigate contact mechanics and tribology. It has known to experience high contact forces and stresses. However, cartilage shows remarkable lubricating and wear properties, and survives the lifetime of a person. Biphasic lubrication based on the principle of fluid load support has provided an explanation for this. However, when, the cartilage fails the part or whole of the joint needs to be replaced and hemiarthroplasty is one such remedy. Three-dimensional finite element models with elastic/hyperelasti

Los estilos APA, Harvard, Vancouver, ISO, etc.

2

Page, Steven M. "Investigation into the Behavior of Bolted Joints." Wright State University / OhioLINK, 2006. http://rave.ohiolink.edu/etdc/view?acc_num=wright1163527930.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

3

Fischer, Seth Gavin. "Joints and connections." Thesis, Virginia Tech, 2004. http://hdl.handle.net/10919/36310.

Texto completo

Resumen

Istanbul is a city on the water and historically has been a link between East and West. Unlike most cities, ferry boats are one of the most commonly used means of travel, along with rail and bus lines. There is a contrast between the grandeur of the historic buildings as seen from the water and the unpleasantness of disembarking from the ferry, which berths at a small shed-like structure on the edge of the water which has old tires attached to piles driven into the bank of the Golden Horn. Some distance away there is a bus terminal and train stop. The paths of travel between these are uncl

Los estilos APA, Harvard, Vancouver, ISO, etc.

4

Lam, Kwok-wai. "Design and development of a new prosthetic device for proximal interphalangeal joint replacement." Click to view the E-thesis via HKUTO, 2007. http://sunzi.lib.hku.hk/hkuto/record/B3889161X.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

5

Schumacher, Brian. "An analysis of the femoral head/stem taper lock for orthopaedic prostheses." Thesis, Georgia Institute of Technology, 1992. http://hdl.handle.net/1853/18927.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

6

Chen, K. C. "Fatigue of dovetail joints." Thesis, University of Oxford, 1985. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.355721.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

7

Helliwell, Philip Stephen. "Stiffness in human joints." Thesis, University of Leeds, 1993. http://etheses.whiterose.ac.uk/4401/.

Texto completo

Resumen

Articular stiffness is an important symptom in most arthritic diseases and appears to be a useful marker of disease activity in rheumatoid arthritis. Attempts to obtain a reliable objective measure of articular stiffness span the last 30 years but a meaningful measure of this symptom remains elusive. A number of reasons have been suggested to explain the discrepancy between objective and subjective stiffness in arthritis and these can be summarised as: a semeiological confusion, aberrant mechano-receptor thresholds and concurrent muscle wasting. This thesis examines each of these hypotheses. S

Los estilos APA, Harvard, Vancouver, ISO, etc.

8

Watson, Peter. "Cavitation in human joints." Thesis, Queen's University Belfast, 1987. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.304536.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

9

Thummalapalli, Vimal Kumar. "Biomimetic Composite T-Joints." University of Dayton / OhioLINK, 2011. http://rave.ohiolink.edu/etdc/view?acc_num=dayton1323547304.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

10

Ghafoori, Roozbahany Ehsan. "Fracture testing and evaluation of asphalt pavement joints in quasi static tension mode." Thesis, KTH, Väg- och banteknik, 2012. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-96672.

Texto completo

Resumen

Asphalt joints are inevitable parts of every pavement. They are constructed for different reasons. Although much attention is dedicated to the construction joints (hot with hot pavement), a scientific approach for cold joints (cold with hot pavement) with respect to large patch constructions is still missing. This report tries to evaluate existing construction techniques and to suggest new testing methods of tests. Although, indirect tensile tests IDT and direct tension tests DTT are familiar in the field of asphalt pavement characterization, they have not been used for the assessment of joint

Los estilos APA, Harvard, Vancouver, ISO, etc.

11

Shou, Guohua. "Joint roughness characterization and effect of roughness on peak shear strength of joints." Diss., The University of Arizona, 1994. http://hdl.handle.net/10150/186804.

Texto completo

Resumen

Rock joint surface roughness is characterized by using statistical parameters and fractal parameters estimated by various methods. It was found that at least two parameters are required to quantify joint surface roughness. By limiting only to statistical parameters, an average I angle is suggested to capture the large-scale undulations (non-stationary part of roughness) and Z₂' is suggested to capture the small-scale roughness (stationary part of roughness). Fractal parameters estimated by different method were used to describe the stationary part of surface roughness. Relation between fractal

Los estilos APA, Harvard, Vancouver, ISO, etc.

12

Cruwys, Simon Charles. "Neurogenic influences on arthritis." Thesis, Queen Mary, University of London, 1996. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.243318.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

13

Pendelton, Alice Mae. "Biofluid lubrication for artificial joints." [College Station, Tex. : Texas A&M University, 2008. http://hdl.handle.net/1969.1/ETD-TAMU-3205.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

14

Tol, Serife. "Dynamic Modeling Of Structural Joints." Master's thesis, METU, 2012. http://etd.lib.metu.edu.tr/upload/12614368/index.pdf.

Texto completo

Resumen

Complex systems composed of many substructures include various structural joints connecting the substructures together. These mechanical connections play a significant role in predicting the dynamic characteristics of the assembled systems accurately. Therefore, equivalent dynamic models of joints that consist of stiffness and damping elements should be developed and the joint parameters should be determined for an accurate vibration analysis. Since it is difficult to estimate joint parameters accurately by using a pure analytical approach, it is a general practice to use experimental measurem

Los estilos APA, Harvard, Vancouver, ISO, etc.

15

Kawashita, Luiz Fernando. "The peeling of adhesive joints." Thesis, Imperial College London, 2006. http://hdl.handle.net/10044/1/7720.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

16

Choudhury, Marcel. "Member stiffness of bolted joints." Thesis, Georgia Institute of Technology, 1988. http://hdl.handle.net/1853/17882.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

17

Korenberg, Capucine Florence. "The durability of adhesive joints." Thesis, Imperial College London, 2002. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.272387.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

18

Manchu, Sreenivasarao. "Parameter Identification for Mechanical Joints." Thesis, Blekinge Tekniska Högskola, Avdelningen för maskinteknik, 2006. http://urn.kb.se/resolve?urn=urn:nbn:se:bth-4309.

Texto completo

Resumen

All but the simplest physical systems contains mechanical joints. The behavior of these joints is sometimes the dominant factor in over all system behavior. The potential for occurence of microslip and macroslip normally makes the behavior of joints non-linear. Accurate modeling of joints requires a non-linear ramework. As clamping pressures are typically random ad variable, the behavior of the joints becomes random. Joint geometries are random along with other unknowns of the joints. Two different methods for measuring the energy dissipation are explained. In the experimental method, the ener

Los estilos APA, Harvard, Vancouver, ISO, etc.

19

Oldfield, Matthew. "Harmonic excitation of bolted joints." Thesis, University of Liverpool, 2004. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.400233.

Texto completo

Resumen

Bolted joints provide one of the most common means of joining two structural components together. The joints themselves use friction to transmit force, torque and motion across a common interface from one component to another. In many cases a pretensioned bolt, running through a common hole at the joint interface, provides the clamping force. The friction force at a joint interface is highly nonlinear. This makes the analysis of dynamic systelTIS with joints unrealistic with conventional linear techniques. It has also been shown that the contact pressure at a joint interface is not necessarily

Los estilos APA, Harvard, Vancouver, ISO, etc.

20

Servis, Dimitris C. "Sound transmission at pipe joints." Thesis, Heriot-Watt University, 1991. http://hdl.handle.net/10399/782.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

21

Judge, R. C. B. "Lapped joints in reinforced concrete." Thesis, Durham University, 1987. http://etheses.dur.ac.uk/6779/.

Texto completo

Resumen

This thesis is concerned with an experimental investigation of the behaviour of lapped joints in reinforced concrete. A review of existing literature highlights the need to establish the longitudinal strain distribution along lap joints. This has been achieved experimentally, with detailed strain measurements being taken using a technique of internally gauging the reinforcing rods. In some specimens, strain concentration gauges were installed at the tip of the lap to permit the acquisition of particularly localised information. Computer programs were developed to process the substantial amount

Los estilos APA, Harvard, Vancouver, ISO, etc.

22

Khalid, Yousif A. "Static strength of tubular joints." Thesis, University of Nottingham, 1993. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.357818.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

23

Hutchinson, Allan Robert. "Durability of structural adhesive joints." Thesis, University of Dundee, 1986. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.245438.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

24

Myers, James C. (James Clinton). "Behavior of fillet sealant joints." Thesis, Massachusetts Institute of Technology, 1989. http://hdl.handle.net/1721.1/14301.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

25

Radighieri, Greg A. (Greg Alan) 1977. "Galling failures in pin joints." Thesis, Massachusetts Institute of Technology, 2002. http://hdl.handle.net/1721.1/89892.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

26

Feih, Stefanie. "Design of composite adhesive joints." Thesis, University of Cambridge, 2002. https://www.repository.cam.ac.uk/handle/1810/284008.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

27

Budzik, Michal. "Fracture in asymmetric bonded joints." Thesis, Bordeaux 1, 2010. http://www.theses.fr/2010BOR14041/document.

Texto completo

Resumen

Des tests de fissuration ont été réalisés sur des joints collés asymétriques. Ces assemblages asymétriques sont constitués de deux substrats de nature et/ou d’épaisseur différentes liés par un adhésif. Cette géométrie d’éprouvette semble peu utilisée pour effectuer des essais de fissuration. Elles présentent certains inconvénients et de ce fait n’ont fait l’objet d’aucune normalisation. Dans le cadre cette géométrie d’éprouvette d’essai a été néanmoins été retenue et utilisée dans trois configurations différentes pour la caractérisation mécanique des assemblages collés. Des protocoles d’essai

Los estilos APA, Harvard, Vancouver, ISO, etc.

28

Bland, David Jonathan. "The durability of adhesive joints." Thesis, Imperial College London, 2009. http://hdl.handle.net/10044/1/5687.

Texto completo

Resumen

One of the most important requirements of an adhesive joint is the ability to retain a significant proportion of its load-bearing capability for the long periods under the wide variety of environmental conditions encountered during its service-life. There exists a need to improve the understanding of the mechanics and mechanisms associated with the durability of adhesive joints in hostile environments, such as one of the most potentially damaging and frequently encountered, water, to further their future extensive use in engineering applications. In the present research, four important aspects

Los estilos APA, Harvard, Vancouver, ISO, etc.

29

Stephen, Joseph Temitope. "Condition monitoring of bolted joints." Thesis, University of Sheffield, 2015. http://etheses.whiterose.ac.uk/10425/.

Texto completo

Resumen

Rail joints have been in existence for a long time of which their design has remained primarily unchanged over this period. Rail joints are a typical example of bolted joints. Like other bolted joints, their integrity depends on the quantitative representation of the contact pressure distribution at the interface during design. In service, rail joints are subjected to complex operating stresses, and they demand high maintenance cost because they are safety critical and have the lowest service life of the components on the rail tracks. In this study, non-intrusive ultrasonic techniques have bee

Los estilos APA, Harvard, Vancouver, ISO, etc.

30

Wu, JiangFan. "Etudes des joints cinématiques coulissants." Paris, CNAM, 1997. http://www.theses.fr/1997CNAM0306.

Texto completo

Resumen

Aprés un bref historique du probléme chapitre I nous avons analysé dans le chapitre II à l'aide de la théorie des mécanismes les différentes solutions possibles de transmission cinématique entre le différentiel et la roue. On montre qu'il existe 3 familles possibles :1) L'une avec une seule boucle cinématique 2)La deuxième utilise 2 boucles cinématiques 3) La troisième utilise 3 boucles cinématiques et conduit aux différents tripodes. Dans le chapitre III on étudie la géome��trie complète des transmissions envisagées. On montre que le joint tripode à point fixe est approché par un mouvement do

Los estilos APA, Harvard, Vancouver, ISO, etc.

31

Jeenjitkaew, Choothum. "Kissing bonds in adhesive joints : a holistic approach for surface chemistry and joint mechanics." Thesis, Queen Mary, University of London, 2011. http://qmro.qmul.ac.uk/xmlui/handle/123456789/1269.

Texto completo

Resumen

Kissing bonds (KBs) refer to the situation where two surfaces are only partially bonded or are debonded but touching or in very close proximity. This may be the consequence of poor adhesion, environmental degradation or impact damage. This defect is not visible macroscopically and because of their intimate contact which makes it more difficult to detect using a non destructive technique (NDT) than conventional defects such as voids or cracks etc. The success of NDT evaluation and widespread use of adhesive bonding rely greatly upon comprehensive knowledge of morphology, surface chemistry and m

Los estilos APA, Harvard, Vancouver, ISO, etc.

32

Mariot, Antoine. "Analyse théorique et expérimentale des joints d'étanchéité à bague flottante et des joints rainurés segmentés." Thesis, Poitiers, 2015. http://www.theses.fr/2015POIT2292/document.

Texto completo

Resumen

Ce mémoire présente une étude théorique et expérimentale de joints annulaires à bague flottante ainsi que de joints rainurés segmentés, destinés à assurer l’étanchéité dynamique au sein de machines tournantes à haute vitesse dans les domaines aéronautique et aérospatial. Des joints annulaires à bague flottante ont été testés sur un banc d’essais dédié au sein de l’institut Pprime pour de multiples configurations de vitesse de rotation et de différence de pression étanchée. La réponse dynamique des joints par rapport aux vibrations du rotor a été étudiée pour différentes amplitudes de l’excitat

Los estilos APA, Harvard, Vancouver, ISO, etc.

33

Chen, Shuenn-muh. "Kinematic and passive resistive properties of human shoulder hip and elbow complexes /." The Ohio State University, 1986. http://rave.ohiolink.edu/etdc/view?acc_num=osu1487266691095932.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

34

Krishna, Karthik. "Estimation of Impedance About the." Digital WPI, 2005. https://digitalcommons.wpi.edu/etd-theses/278.

Texto completo

Resumen

In performing manual tasks, muscles are voluntarily contracted in order to produce force and orient the limb in the desired direction. Many occupational tasks are associated with frequent musculoskeletal disorders. In tasks involving skilful manipulation, very frequently the forces are focused on the upper limb and neck. Upper extremity cumulative trauma disorders are among the more common worker related injuries. These muscle disorders may be related to repetitive exertions, excessive muscle loads and extreme postures. One of the major challenges is to quantify the muscle load and researchers

Los estilos APA, Harvard, Vancouver, ISO, etc.

35

Carroll, Jeffery D. "Withdrawal and combined load capacity of threaded fastener wood joints /." This resource online, 1988. http://scholar.lib.vt.edu/theses/available/etd-04122010-083654/.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

36

關健明 and Kin-ming Kwan. "An expert system for adhesive-bonded joints." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 1995. http://hub.hku.hk/bib/B31212347.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

37

Kwan, Kin-ming. "An expert system for adhesive-bonded joints /." Hong Kong : University of Hong Kong, 1995. http://sunzi.lib.hku.hk/hkuto/record.jsp?B14038651.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

38

Malladi, Sailaja. "Parametric modeling and analysis of structural bonded joints." Morgantown, W. Va. : [West Virginia University Libraries], 2004. https://etd.wvu.edu/etd/controller.jsp?moduleName=documentdata&jsp%5FetdId=80.

Texto completo

Resumen

Thesis (M.S.)--West Virginia University, 2004.<br>Title from document title page. Document formatted into pages; contains x, 56 p. : ill. (some col.). Includes abstract. Includes bibliographical references (p. 52-53).

Los estilos APA, Harvard, Vancouver, ISO, etc.

39

Jones, Timothy G. B. "Effect of movement during cure on the experimental performance of construction sealant materials." Thesis, Oxford Brookes University, 2001. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.327679.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

40

Varela, Valdez Alberto. "Mechanical behavior of rock joints : influence of joint roughness on its closure and shear behavior." Thesis, Bordeaux, 2015. http://www.theses.fr/2015BORD0184/document.

Texto completo

Resumen

Le comportement mécanique en cisaillement sous contrainte normale constante de joints rocheux est étudié en utilisant une approche numérique par éléments discrets (DEM Discrete Element Model). Les influences respectives de la rugosité des surfaces des joints, de l'élasticité des épontes, de la rupture des aspérités de surface et du niveau de contrainte de compression sur les comportements en fermeture et cisaillement des joints rocheux sont particulièrement analysées. Pour la première fois la rugosité des joints considérée comme auto-affine est utilisée avec DEM pour étudier le frottement des

Los estilos APA, Harvard, Vancouver, ISO, etc.

41

Sousa, Ticiana Meireles. "Analysis of cartilage wear particles in equine joints and their relationship to serveral joint diseases /." Berlin : Mbv, 2008. http://d-nb.info/991425898/04.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

42

Pellan, Maxime. "Développement des joints de grain et des joints de phase dans les carbures cémentés WC-CO." Thesis, Université Grenoble Alpes (ComUE), 2015. http://www.theses.fr/2015GREAI121/document.

Texto completo

Resumen

Le carbure cémenté (WC-Co) est un système biphasé constitué de grains de carbure de tungstène enrobés dans un liant à base de cobalt. Dans ce matériau composite, qui allie donc la dureté du carbure à la résilience du cobalt, la maîtrise de la microstructure est un paramètre clef pour l’optimisation des propriétés mécaniques.Le but de ce travail est de mettre au jour les mécanismes régissant le développement des joint de grain et des joints de phase lors du frittage. L’effet de la teneur en liant, du taux de carbone et du temps de frittage ont été particulièrement étudiés.Ce travail est basée s

Los estilos APA, Harvard, Vancouver, ISO, etc.

43

Bary, Abdouraman. "Etude par tem et ebic des joints, sous-joints et precipites dans le silicium polycristallin polix." Caen, 1989. http://www.theses.fr/1989CAEN2031.

Texto completo

Resumen

La structure cristallographique des principaux defauts presents dans les lingots bruts de silicium polycristallin de type polix a ete etudiee par microscopie electronique en transmission (met). Une methode analytique a permis de determiner de facon tres precise des parametres qui caracterisent les joints de grains et les sous-joints. Les precipites presents dans ce materiau ont ete egalement caracterises. Parallelement a cette description structurale, l'activite electrique de ces defauts a ete etudiee au moyen de la microscopie electronique a balayage (meb) par la technique du courant induit p

Los estilos APA, Harvard, Vancouver, ISO, etc.

44

Bary, Abdouraman. "Etude par TEM et EBIC des joints, sous-joints et précipités dans le silicium polycristallin POLIX." Grenoble 2 : ANRT, 1988. http://catalogue.bnf.fr/ark:/12148/cb37611619w.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

45

Schmidt, Peter. "Computational Models of Adhesively Bonded Joints." Doctoral thesis, Linköping : Division of Mechanics, Department of Management and Engineering, Linköping University, 2007. http://www.bibl.liu.se/liupubl/disp/disp2007/tek1076s.pdf.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

46

Butkus, Lawrence M. "Environmental durability of adhesively bonded joints." Diss., Georgia Institute of Technology, 1997. http://hdl.handle.net/1853/19008.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

47

Little, Matthew S. G. "The durability of structural adhesive joints." Thesis, Imperial College London, 1999. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.417769.

Texto completo

Los estilos APA, Harvard, Vancouver, ISO, etc.

48

Clifford, S. "Fracture behaviour of metal-composite joints." Thesis, University of Cambridge, 2003. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.597775.

Texto completo

Resumen

The fracture behaviour of polymer composite-metal joints has been investigated within the context of two real joint applications. A joint intended for the joining of a glass-fibre reinforced vinylester composite (GRP) superstructure to the steel deck of a naval vessel was the starting point for the project. The novel technique lies in the manufacture of the joint in that a steel adherend is incorporated into the superstructure panel during the manufacture of the panel itself by a resin infusion moulding process. One end of this adherend protrudes from the finished panel which can then be welde

Los estilos APA, Harvard, Vancouver, ISO, etc.

49

Sanchez, Francisco Sebastian Rodriguez. "Fracture Behaviour of Automotive Adhesive Joints." Thesis, Imperial College London, 2008. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.485405.

Texto completo

Resumen

Adhesives can enable significant weight reductions in automotive constructions. However, the performance of adhesive joints and the energy absorption of bonded structures needs to be well understood. This thesis describes the perfonnance of a number of automotive adhesive joints using a fracture mechanics approach. The fracture energy, Gc ' was used to characterise the joint perfonnance during different modes of loading at low and high r,ates. A detailed analysis strategy was developed to account for the different types of crack propagatidn observed and the high rate effects encountered. This

Los estilos APA, Harvard, Vancouver, ISO, etc.

50

Bigwood, David Andrew. "The design of structural adhesive joints." Thesis, University of Surrey, 1990. http://epubs.surrey.ac.uk/770397/.

Texto completo

Resumen

This thesis details the work carried out under two research projects at the University of Surrey. The first project titled The Design of Structural Adhesive Joints', was of three years duration from September 1985 to August 1988 and was sponsored by the Science and Engineering Research Council. The second project, sponsored by Ford UK Ltd, and tided 'A General Joint Analysis Facility extended certain aspects of the analysis work initiated In the first period of research. The objective of the work was to address the problem of integrating structural adhesives Into the design process and to prov

Los estilos APA, Harvard, Vancouver, ISO, etc.

Ofrecemos descuentos en todos los planes premium para autores cuyas obras están incluidas en selecciones literarias temáticas. ¡Contáctenos para obtener un código promocional único!