Se connecter

Bibliographies thématiques / Automotive components / Articles de revues

Pour voir les autres types de publications sur ce sujet consultez le lien suivant : Automotive components.

Articles de revues sur le sujet « Automotive components »

Auteur : Grafiati

Publié le 4 juin 2021

Mis à jour le 19 février 2022

Créez une référence correcte selon les styles APA, MLA, Chicago, Harvard et plusieurs autres

Choisissez une source :

Consultez les 50 meilleurs articles de revues pour votre recherche sur le sujet « Automotive components ».

À côté de chaque source dans la liste de références il y a un bouton « Ajouter à la bibliographie ». Cliquez sur ce bouton, et nous générerons automatiquement la référence bibliographique pour la source choisie selon votre style de citation préféré : APA, MLA, Harvard, Vancouver, Chicago, etc.

Vous pouvez aussi télécharger le texte intégral de la publication scolaire au format pdf et consulter son résumé en ligne lorsque ces informations sont inclues dans les métadonnées.

Parcourez les articles de revues sur diverses disciplines et organisez correctement votre bibliographie.

1

Wang, Jun Jun, Lu Wang, and Ming Chen. "Automotive Electronic Control Components Energy Consumption and Environmental Emissions Analysis in China Based on Economic Input-Output Life-Cycle Assessment Model." Advanced Materials Research 479-481 (February 2012): 2177–81. http://dx.doi.org/10.4028/www.scientific.net/amr.479-481.2177.

Texte intégral

Résumé :

With the rapid growth of vehicle population and electronic control components used in automotives in China, the energy consumption and environmental emissions of automotive electronic control components in 2007 are calculated by adopting the EIO-LCA model. The calculation results indicate that automotive electronic control components consume 20306000 tons of standard coal equivalent (SCE), which is a large consumption of energy, and make a lot of toxic environmental emissions. However, in China, after the automotives are scrapped, the automotive electronic components are either discarded carel

Styles APA, Harvard, Vancouver, ISO, etc.

2

Wen, Bing Quan, Xia Xie, and Bin Wang. "Review of Remanufacturing for Automotive Components." Applied Mechanics and Materials 182-183 (June 2012): 482–85. http://dx.doi.org/10.4028/www.scientific.net/amm.182-183.482.

Texte intégral

Résumé :

Based on the concept of the remanufacturing for automotive components, the significance of implementing the remanufacturing was analyzed in this paper. And then the advanced technologies of automotive remanufacturing were focused on with some examples, such as the electro-brush plating technology, high-speed arc spraying technology, hypersonic velocity plasma spraying technology, scratch fast fill technology, and so on. In the end the conclusion was educed that the automotive remanufacturing is significant to the sustainable development of the society economy and the environmental protection,

Styles APA, Harvard, Vancouver, ISO, etc.

3

Kumar, Nithin, and Ajay Gopalswamy. "Robots in Welding of Automotive Components." Indian Welding Journal 36, no. 4 (October 1, 2003): 38. http://dx.doi.org/10.22486/iwj.v36i4.178781.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

4

Ahn, Young-Nam, and Cheol-Hee Kim. "Laser Welding of Automotive Transmission Components." Journal of the Korean Welding and Joining Society 29, no. 6 (December 31, 2011): 45–48. http://dx.doi.org/10.5781/kwjs.2011.29.6.665.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

5

Feldmann, K., B. Müller, and T. Haselmann. "Automated Assembly of Lightweight Automotive Components." CIRP Annals 48, no. 1 (1999): 9–12. http://dx.doi.org/10.1016/s0007-8506(07)63120-5.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

6

Beretta, S. "Defect tolerant design of automotive components." International Journal of Fatigue 19, no. 4 (April 1997): 319–33. http://dx.doi.org/10.1016/s0142-1123(96)00079-5.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

7

Magurno, Antonio. "Vegetable fibres in automotive interior components." Die Angewandte Makromolekulare Chemie 272, no. 1 (December 1, 1999): 99–107. http://dx.doi.org/10.1002/(sici)1522-9505(19991201)272:1<99::aid-apmc99>3.0.co;2-c.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

8

Ivasishin, O. M., D. G. Sawakin, V. S. Moxson, K. A. Bondareval, and F. H. (Sam) Froes. "Titanium Powder Metallurgy for Automotive Components." Materials Technology 17, no. 1 (January 2002): 20–25. http://dx.doi.org/10.1080/10667857.2002.11752959.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

9

Fitri, Muhamad, S. Mahzan, and Fajar Anggara. "The Mechanical Properties Requirement for Polymer Composite Automotive Parts - A Review." International Journal of Advanced Technology in Mechanical, Mechatronics and Materials 1, no. 3 (January 1, 2021): 125–33. http://dx.doi.org/10.37869/ijatec.v1i3.38.

Texte intégral

Résumé :

Indonesia has a large variety of natural fibers in abundance. Some of natural fibers become organic waste if not used for something needed by humans. One of the potential uses of natural fiber composite materials is to be used in automotive components. But before natural fiber composites are used in automotive components, it is necessary to examine first what are the requirements for mechanical properties or other properties required by the automotive components. Especially the automotive components which have been made from Polymers, like dash board, Car interior walls, front and rear bumper

Styles APA, Harvard, Vancouver, ISO, etc.

10

George, John, Kishore Pydimarry, Jeremy Seidt, and Kelton Rieske. "Ductile Fracture Prediction of Automotive Suspension Components." SAE International Journal of Engines 10, no. 2 (March 28, 2017): 280–86. http://dx.doi.org/10.4271/2017-01-0318.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

11

Wang, Liang, Robert Burger, and Alan Aloe. "Considerations of Vibration Fatigue for Automotive Components." SAE International Journal of Commercial Vehicles 10, no. 1 (March 28, 2017): 150–58. http://dx.doi.org/10.4271/2017-01-0380.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

12

Bone, Gary M., and David Capson. "Vision-guided fixtureless assembly of automotive components." Robotics and Computer-Integrated Manufacturing 19, no. 1-2 (February 2003): 79–87. http://dx.doi.org/10.1016/s0736-5845(02)00064-9.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

13

Potgieter, J. H., M. Sephton, and Z. W. Nkosi. "Corrosion of hot end automotive exhaust components." Anti-Corrosion Methods and Materials 54, no. 3 (May 29, 2007): 180–87. http://dx.doi.org/10.1108/00035590710748650.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

14

Soderquist, Klas Eric, Jean-Jacques Chanaron, and David Birchall. "Automotive components suppliers facing the learning challenge." International Journal of Automotive Technology and Management 1, no. 2/3 (2001): 252. http://dx.doi.org/10.1504/ijatm.2001.000038.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

15

Naskar, Amit K., Jong K. Keum, and Raymond G. Boeman. "Polymer matrix nanocomposites for automotive structural components." Nature Nanotechnology 11, no. 12 (December 2016): 1026–30. http://dx.doi.org/10.1038/nnano.2016.262.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

16

Marcello Pelagagge, Pacifico. "Advanced manufacturing system for automotive components production." Industrial Management & Data Systems 97, no. 8 (December 1997): 327–34. http://dx.doi.org/10.1108/02635579710195055.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

17

Petersen, DR, RE Link, R. Lopes, A. Mazzeranghi, G. Ronchiato, and D. Vangi. "An Ultrasonic Technique for Monitoring Automotive Components." Journal of Testing and Evaluation 25, no. 5 (1997): 516. http://dx.doi.org/10.1520/jte11363j.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

18

Munikamal, Tiruttani, and Suresh Sundarraj. "Modeling the Case Hardening of Automotive Components." Metallurgical and Materials Transactions B 44, no. 2 (December 15, 2012): 436–46. http://dx.doi.org/10.1007/s11663-012-9775-7.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

19

Faccoli, M., G. Cornacchia, M. Gelfi, A. Panvini, and R. Roberti. "Notch ductility of steels for automotive components." Engineering Fracture Mechanics 127 (September 2014): 181–93. http://dx.doi.org/10.1016/j.engfracmech.2014.06.007.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

20

Rosenthal, Stephan, Fabian Maaß, Mike Kamaliev, Marlon Hahn, Soeren Gies, and A. Erman Tekkaya. "Lightweight in Automotive Components by Forming Technology." Automotive Innovation 3, no. 3 (July 31, 2020): 195–209. http://dx.doi.org/10.1007/s42154-020-00103-3.

Texte intégral

Résumé :

AbstractLightweight design is one of the current key drivers to reduce the energy consumption of vehicles. Design methodologies for lightweight components, strategies utilizing materials with favorable specific properties and hybrid materials are used to increase the performance of parts for automotive applications. In this paper, various forming processes to produce light parts are described. Material lightweight design is discussed, covering the manufacturing processes to produce hybrid components like fiber–metal, polymer–metal and metal–metal composites, which can be used in subsequent dee

Styles APA, Harvard, Vancouver, ISO, etc.

21

Bertuol, B. "Sensors as key components for automotive systems." Sensors and Actuators A: Physical 25, no. 1-3 (October 1990): 95–102. http://dx.doi.org/10.1016/0924-4247(90)87014-a.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

22

Aldridge, Dustin S. "Determining Thermal Test Requirements for Automotive Components." Quality and Reliability Engineering International 20, no. 2 (February 25, 2004): 103–13. http://dx.doi.org/10.1002/qre.618.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

23

Permatasari, Sheila Silvia, and Mukaram Mukaram. "Pengaruh Rasio Keuangan Terhadap Harga Saham." Jurnal Riset Bisnis dan Investasi 4, no. 3 (February 6, 2019): 47. http://dx.doi.org/10.35697/jrbi.v4i3.1256.

Texte intégral

Résumé :

This study aims to influence the financial ratios of stock prices on the issuers of automotive sector companies and components listed on the Indonesia Stock Exchange period 2011-2016. This study is a documentation study, where the data used is secondary data obtained from company reports that have been available. The population in this research is all companies of automotive sector and components listed in IDX and reporting company's finance in period 2011-2016. From a total of 13 companies, 12 companies were taken as samples because one company did not meet the requirements of the financial s

Styles APA, Harvard, Vancouver, ISO, etc.

24

Ahmad, Mohd Nizam, Awanis Ihsanul Kamil, and Wan Mansor Wan Muhamad. "Application of Shape Optimization Method on Steel Wheel Rim." Applied Mechanics and Materials 564 (June 2014): 13–18. http://dx.doi.org/10.4028/www.scientific.net/amm.564.13.

Texte intégral

Résumé :

Nowadays, weight reduction is great opportunity for automotive components design due to meet the structural strength without reducing the components safety. A classical try-and-error approach to design the automotive components in industries is inadequate which mean new methods are needed to enhance the design process. An improvement of the component can be achieved by adopting suitable optimization techniques at the early design stage. In this paper, the problem of automotive component design; steel wheel rim design in a view of weight reduction was tackled by means of shape optimization meth

Styles APA, Harvard, Vancouver, ISO, etc.

25

Johnson, A. R. "Integrated CADCAM and Automotive Die and Mould Manufacture." Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering 203, no. 2 (April 1989): 137–44. http://dx.doi.org/10.1243/pime_proc_1989_203_159_02.

Texte intégral

Résumé :

Many automotive components are produced in very large quantities using manufacturing processes such as casting, moulding and forging. These processes require tooling which usually has geometrical complexities such as doubly curved surfaces, fillet curves, split lines and draft angles. Traditionally the component design is conveyed to the toolmaker for manufacture of the tooling, using conventional engineering drawings. The paper shows how tooling and component problems can arise due to the inability of conventional two-dimensional engineering drawings to unambiguously define complex three-dime

Styles APA, Harvard, Vancouver, ISO, etc.

26

Garg, Mohit, and Richard Lai. "A Method for Measuring the Constraint Complexity of Components in Automotive Embedded Software Systems." International Journal of Software Engineering and Knowledge Engineering 29, no. 01 (January 2019): 1–21. http://dx.doi.org/10.1142/s0218194019500013.

Texte intégral

Résumé :

The rapid growth of software-based functionalities has made automotive Electronic Control Units (ECUs) significantly complex. Factors affecting the software complexity of components embedded in an ECU depend not only on their interface and interaction properties, but also on the structural constraints characterized by a component’s functional semantics and timing constraints described by AUTomotive Open System ARchitecture (AUTOSAR) languages. Traditional constraint complexity measures are not adequate for the components in embedded software systems as they do not yet sufficiently provide a me

Styles APA, Harvard, Vancouver, ISO, etc.

27

KAWALLA, Claudia, Mariusz LIGARSKI, and Michael HÖCK. "SUPPLY CHAIN QUALITY MANAGEMENT OF AUTOMOTIVE 2 COMPONENTS." Scientific Papers of Silesian University of Technology. Organization and Management Series 2019, no. 133 (2019): 69–83. http://dx.doi.org/10.29119/1641-3466.2019.133.6.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

28

YAMASHITA, Yoshihiro. "Alternative Press Fitting Using Laser for Automotive Components." Review of Laser Engineering 35, no. 12 (2007): 799–805. http://dx.doi.org/10.2184/lsj.35.799.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

29

Denkena, Berend, Thilo Grove, and Alexander Krödel. "A New Tool Concept for Milling Automotive Components." Procedia CIRP 46 (2016): 444–47. http://dx.doi.org/10.1016/j.procir.2016.04.055.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

30

Bahi, M. A., P. Lecuyer, H. Fremont, and J.-P. Landesman. "Sequential environmental stresses tests qualification for automotive components." Microelectronics Reliability 47, no. 9-11 (September 2007): 1680–84. http://dx.doi.org/10.1016/j.microrel.2007.07.004.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

31

Guariente, P., I. Antoniolli, L. Pinto Ferreira, T. Pereira, and F. J. G. Silva. "Implementing autonomous maintenance in an automotive components manufacturer." Procedia Manufacturing 13 (2017): 1128–34. http://dx.doi.org/10.1016/j.promfg.2017.09.174.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

32

Felde, I., and C. Simsir. "Simulation trends in quenching technology for automotive components." International Heat Treatment and Surface Engineering 8, no. 1 (December 6, 2013): 42–48. http://dx.doi.org/10.1179/1749514813z.00000000097.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

33

Aktary, M., M. T. McDermott, and G. MacAlpine. "Morphology and Nanoindentation Profiles of Automotive Engine Components." Surface Engineering 18, no. 1 (February 28, 2002): 70–74. http://dx.doi.org/10.1179/026708401225001273.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

34

Ronen, Aviram, Izhak Etsion, and Yuri Kligerman. "Friction-Reducing Surface-Texturing in Reciprocating Automotive Components." Tribology Transactions 44, no. 3 (January 2001): 359–66. http://dx.doi.org/10.1080/10402000108982468.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

35

Karakoyun, F., D. Kiritsis, and K. Martinsen. "Holistic life cycle approach for lightweight automotive components." Metallurgical Research & Technology 111, no. 3 (2014): 137–46. http://dx.doi.org/10.1051/metal/2014034.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

36

Behrens, B. A., E. Doege, S. Reinsch, K. Telkamp, H. Daehndel, and A. Specker. "Precision forging processes for high-duty automotive components." Journal of Materials Processing Technology 185, no. 1-3 (April 2007): 139–46. http://dx.doi.org/10.1016/j.jmatprotec.2006.03.132.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

37

Botkin, M. E., D. Bajorek, and M. Prasad. "Feature-based structural design of solid automotive components." Finite Elements in Analysis and Design 16, no. 1 (April 1994): 15–26. http://dx.doi.org/10.1016/0168-874x(94)90037-x.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

38

Yuan, S. J., C. Han, and X. S. Wang. "Hydroforming of automotive structural components with rectangular-sections." International Journal of Machine Tools and Manufacture 46, no. 11 (September 2006): 1201–6. http://dx.doi.org/10.1016/j.ijmachtools.2006.01.038.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

39

Wallace, P. L. "Radlite: powder to parts manufacture of automotive components." Composites Manufacturing 1, no. 2 (June 1990): 109–11. http://dx.doi.org/10.1016/0956-7143(90)90245-r.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

40

LeBeau, S. "Production of automotive components from mechanically ground powder." Metal Powder Report 47, no. 11 (November 1992): 56. http://dx.doi.org/10.1016/0026-0657(92)90983-l.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

41

Iberahim, Fathiyyah, Dzuraidah Abd Wahab, Zulkifli Mohd Nopiah, and Shahrum Abdullah. "Establishment of Remanufacturing Index for Locally Manufactured Automotive Components." Key Engineering Materials 486 (July 2011): 77–80. http://dx.doi.org/10.4028/www.scientific.net/kem.486.77.

Texte intégral

Résumé :

Remanufacturing is aimed at restoring used automotive components to their new condition with the same function. In order to facilitate remanufacturing, it is important for the industry to ascertain remanufacturability of potential automotive components in the form of quantitative metrics or index. This knowledge is essential for decision making and planning for recovery activities of the end-of-life components. Knowledge on remanufacturability at the design and development stages is also vital so that products can be designed with a high remanufacturability index. This paper reports a study th

Styles APA, Harvard, Vancouver, ISO, etc.

42

Mosey, Sarah, Feras Korkees, Andrew Rees, and Gethin Llewelyn. "Investigation into fibre orientation and weldline reduction of injection moulded short glass-fibre/polyamide 6-6 automotive components." Journal of Thermoplastic Composite Materials 33, no. 12 (April 8, 2019): 1603–28. http://dx.doi.org/10.1177/0892705719833098.

Texte intégral

Résumé :

Due to the increasing demands on automotive components, manufacturers are relying on injection moulding components from fibre-reinforced polymers in an attempt to increase strength to weight ratio. The use of reinforcing fibres in injection moulded components has led to component failures whereby the material strength is hampered through the formation of weldlines which are also a problem for unreinforced plastics. In this study, an industrial demonstrator component has the injection locations verified through a combination of fibre orientation tensor simulation and optical microscopy analysis

Styles APA, Harvard, Vancouver, ISO, etc.

43

Sapuan, S. M., N. Suddin, and M. A. Maleque. "A Critical Review of Polymer-based Composite Automotive Bumper Systems." Polymers and Polymer Composites 10, no. 8 (November 2002): 627–36. http://dx.doi.org/10.1177/096739110201000806.

Texte intégral

Résumé :

An automobile bumper is a structural component, which contributes to vehicle crashworthiness or occupant protection during front or rear collisions. The bumper systems also protect the hood, trunk, fuel, exhaust and cooling system as well as safety related equipments. A brief description of bumper components and a critical review of polymer-based bumper systems with specific methodology are provided. This article advocates proper bumper design and material selection. The authors also discuss bumper components from the standpoint of the materials and their manufacturing processes.

Styles APA, Harvard, Vancouver, ISO, etc.

44

Madhusudhanan, S., I. Rajendran, and K. Prabu. "Static Analysis of Automotive Steering Knuckle." Applied Mechanics and Materials 592-594 (July 2014): 1155–59. http://dx.doi.org/10.4028/www.scientific.net/amm.592-594.1155.

Texte intégral

Résumé :

Steering knuckle is one of the critical components for a four wheel vehicle which links suspension, steering system, wheel hub and brake to the chassis. While undergoing varying loads subjected to different conditions, it doesn’t affect vehicle steering performance and other desired vehicle characteristics. The static strength test for steering knuckle is necessary to validate the component according to the application. Here, the steering arm static analysis of steering knuckle was done by using finite element analysis (FEA software) and experimental testing by using hydraulic actuators and fi

Styles APA, Harvard, Vancouver, ISO, etc.

45

Kolarovszki, Peter, and Jiří Tengler. "Innovation in Field of Automatic Identification by Selected Components in the Automobile Industry." Applied Mechanics and Materials 803 (October 2015): 223–30. http://dx.doi.org/10.4028/www.scientific.net/amm.803.223.

Texte intégral

Résumé :

Article provides research in field of automatic identification by selected components through radio-frequency identification technology (RFID) in conjunction with automotive industry. The ambition of our research was to achieve 100 % readability of RFID tags placed on selected component. Measurements were done at company providing signal lights for automotive industry and all results had been measured in real condition. A special section is dedicated to description of the technical equipment, used during measurements as well as their results from MySQL database.

Styles APA, Harvard, Vancouver, ISO, etc.

46

Aldridge, Dustin. "Environmental Engineering Within the Automotive Component Development Process." Journal of the IEST 36, no. 1 (January 1, 1993): 19–25. http://dx.doi.org/10.17764/jiet.2.36.1.j02377334ggp4538.

Texte intégral

Résumé :

This paper discusses a test engineering philosophy and the development of knowledge-based tests for automotive components. To ensure success in the product delivery process, accurate measures of total product quality comprised of quality, reliability, durability, performance (QRDP) must be provided to the product development team. Accuracy in environmental testing for automotive components involves the integration of customer-usage, geographic, and application data into the test specifications. Discussion of the inputs required for knowledge-based tests are provided for the automotive vibratio

Styles APA, Harvard, Vancouver, ISO, etc.

47

Schmitt, Matt, Raj Mattias Mehta, and Il Yong Kim. "Additive manufacturing infill optimization for automotive 3D-printed ABS components." Rapid Prototyping Journal 26, no. 1 (January 6, 2020): 89–99. http://dx.doi.org/10.1108/rpj-01-2019-0007.

Texte intégral

Résumé :

Purpose Lightweighting of components in the automotive industry is a prevailing trend influenced by both consumer demand and government regulations. As the viability of additively manufactured designs continues to increase, traditionally manufactured components are continually being replaced with 3D-printed parts. The purpose of this paper is to present experimental results and design considerations for 3D-printed acrylonitrile butadiene styrene (ABS) components with non-solid infill sections, addressing a large gap in the literature. Information published in this paper will guide engineers wh

Styles APA, Harvard, Vancouver, ISO, etc.

48

Issler, Stephan, Manfred Bacher-Hoechst, and Steffen Schmid. "Fatigue Designing of High Strength Steels Components Considering Aggressive Fuel Environment and Very High Cycle Fatigue Effects." Materials Science Forum 783-786 (May 2014): 1845–50. http://dx.doi.org/10.4028/www.scientific.net/msf.783-786.1845.

Texte intégral

Résumé :

Automotive components for injection systems are subjected to load spectra with up to 1E9 load cycles during the expected service life. However, fatigue testing with such a large number of cycles using original components is extremely time-consuming and expensive. A contribution for fatigue reliability assessment is available by the application of specimen testing and the transfer of the results to components including the verification by component spot tests.In this contribution very high cycle fatigue results in laboratory air and in ethanol fuel using notched specimens of high strength stain

Styles APA, Harvard, Vancouver, ISO, etc.

49

ONODA, Motonobu. "Automotive Technology and Earth Environment. Surface Technology of Automotive Engine Components to Prevent Environmental Pollution." Journal of the Surface Finishing Society of Japan 48, no. 6 (1997): 604–9. http://dx.doi.org/10.4139/sfj.48.604.

Texte intégral

Styles APA, Harvard, Vancouver, ISO, etc.

50

Novacek, Jan, Alexander Viehl, Oliver Bringmann, and Wolfgang Rosenstiel. "Reasoning-Supported Robustness Validation of Automotive E/E Components." International Journal of Semantic Computing 11, no. 04 (December 2017): 473–96. http://dx.doi.org/10.1142/s1793351x17400190.

Texte intégral

Résumé :

This article presents an ontology-supported approach to tackle the complexity of the Robustness Validation (RV) process of automotive electrical/electronic (E/E) components. The approach uses formalized knowledge from the RV process and stress, operating, and load profiles, so-called Mission Profiles (MPs). In contrast to the error-prone industrially established manual procedure, we show how component characteristics are formalized in OWL in order to form the foundation of an efficient automated analysis selection and decision support during the RV process. Additionally, a rule-based transform

Styles APA, Harvard, Vancouver, ISO, etc.

Nous offrons des réductions sur tous les plans premium pour les auteurs dont les œuvres sont incluses dans des sélections littéraires thématiques. Contactez-nous pour obtenir un code promo unique!