Accedi

Bibliografie tematiche / Forced convection boiling

Indice

Articoli di riviste
Tesi
Libri
Capitoli di libri
Atti di convegni
Rapporti di organizzazioni

Letteratura scientifica selezionata sul tema "Forced convection boiling"

Autore: Grafiati

Pubblicato: 4 giugno 2021

Ultima modifica: 8 febbraio 2022

Cita una fonte nei formati APA, MLA, Chicago, Harvard e in molti altri stili

Scegli il tipo di fonte:

Consulta la lista di attuali articoli, libri, tesi, atti di convegni e altre fonti scientifiche attinenti al tema "Forced convection boiling".

Accanto a ogni fonte nell'elenco di riferimenti c'è un pulsante "Aggiungi alla bibliografia". Premilo e genereremo automaticamente la citazione bibliografica dell'opera scelta nello stile citazionale di cui hai bisogno: APA, MLA, Harvard, Chicago, Vancouver ecc.

Puoi anche scaricare il testo completo della pubblicazione scientifica nel formato .pdf e leggere online l'abstract (il sommario) dell'opera se è presente nei metadati.

Articoli di riviste sul tema "Forced convection boiling"

1

Ji, Wang, Liu Yujun, Ji Zhuoshang, Deng Yanping, and Zhang Jun. "Study on Forced Convection Boundary Condition for Subcooled Water in the Simulation of Line-Heating Process." Journal of Ship Production 22, no. 01 (February 1, 2006): 41–47. http://dx.doi.org/10.5957/jsp.2006.22.1.41.

Testo completo

Abstract (sommario):

In the simulation of line-heating process, the convection boundary condition, especially the subcooled water forced convection, has great influence on the result. The calculation of the convection coefficient is a difficult problem in the simulation. This paper uses the theory of forced convection boiling to study subcooled water forced convection during the line-heating process. By solving the wall temperatures of originating nucleate boiling and critical heat flux for subcooled water and comparing the plate temperature with these two wall temperatures, the status of water can be determined,

Gli stili APA, Harvard, Vancouver, ISO e altri

2

Auracher, H. "Forced convection transition boiling of refrigerants." International Journal of Refrigeration 11, no. 5 (September 1988): 329–35. http://dx.doi.org/10.1016/0140-7007(88)90097-7.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

3

Zeng, L. Z., and J. F. Klausner. "Nucleation Site Density in Forced Convection Boiling." Journal of Heat Transfer 115, no. 1 (February 1, 1993): 215–21. http://dx.doi.org/10.1115/1.2910651.

Testo completo

Abstract (sommario):

Measurements of nucleation site density, n/A, have been obtained for forced convection boiling of refrigerant R113 in a horizontal 25 × 25 mm i.d. square transparent test section with a nichrome heating strip. It has been found that the behavior of the nucleation site density is significantly different from that found in pool boiling. The mean vapor velocity, heat flux, and system pressure appear to exert a strong parametric influence. It is demonstrated that although the nucleation site density is dependent on the critical cavity radius, rc, it is not sufficient for correlating n/A.

Gli stili APA, Harvard, Vancouver, ISO e altri

4

Podowski, Michael Z., and Raf M. Podowski. "Mechanistic Multidimensional Modeling of Forced Convection Boiling Heat Transfer." Science and Technology of Nuclear Installations 2009 (2009): 1–10. http://dx.doi.org/10.1155/2009/387020.

Testo completo

Abstract (sommario):

Due to the importance of boiling heat transfer in general, and boiling crisis in particular, for the analysis of operation and safety of both nuclear reactors and conventional thermal power systems, extensive efforts have been made in the past to develop a variety of methods and tools to evaluate the boiling heat transfer coefficient and to assess the onset of temperature excursion and critical heat flux (CHF) at various operating conditions of boiling channels. The objective of this paper is to present mathematical modeling concepts behind the development of mechanistic multidimensional model

Gli stili APA, Harvard, Vancouver, ISO e altri

5

MURATA, Keiji, and Kenichi HASHIZUME. "Forced convection boiling of non-azeotropic mixtures." Transactions of the Japan Society of Mechanical Engineers Series B 54, no. 506 (1988): 2856–63. http://dx.doi.org/10.1299/kikaib.54.2856.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

6

NAKAYAMA, Akira, and Hitoshi KOYAMA. "Forced convection film boiling on a wedge." Transactions of the Japan Society of Mechanical Engineers Series B 51, no. 472 (1985): 4334–36. http://dx.doi.org/10.1299/kikaib.51.4334.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

7

Vasil'yev, A. A. "Heat Transfer in Forced-Convection Film Boiling." International Journal of Fluid Mechanics Research 22, no. 2 (1995): 66–72. http://dx.doi.org/10.1615/interjfluidmechres.v22.i2.40.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

8

Sivagnanam, P., A. R. Balakrishnan, and Y. B. G. Varma. "Forced convection subcooled boiling of binary mixtures." Canadian Journal of Chemical Engineering 70, no. 1 (February 1992): 42–47. http://dx.doi.org/10.1002/cjce.5450700107.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

9

Chappidi, P. R., F. S. Gunnerson, and K. O. Pasamehmetoglu. "A simple forced convection film boiling model." International Communications in Heat and Mass Transfer 17, no. 3 (May 1990): 259–70. http://dx.doi.org/10.1016/0735-1933(90)90091-w.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

10

Klausner, J. F., R. Mei, D. M. Bernhard, and L. Z. Zeng. "Vapor bubble departure in forced convection boiling." International Journal of Heat and Mass Transfer 36, no. 3 (February 1993): 651–62. http://dx.doi.org/10.1016/0017-9310(93)80041-r.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

Più fonti

Tesi sul tema "Forced convection boiling"

1

Aziz, S. "Forced convection film boiling on spheres." Thesis, University of Oxford, 1986. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.371536.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

2

Hama, Katsuhiko. "Film boiling heat transfer in various liquids under natural convection and forced convection conditions." Kyoto University, 2006. http://hdl.handle.net/2433/143793.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

3

Doder, Dejan. "Experimental analysis of the pressure characteristic curve of a forced convection boiling flow in single horizontal channel." Thesis, Norges Teknisk-Naturvitenskaplige Universitet, 2013. http://urn.kb.se/resolve?urn=urn:nbn:no:ntnu:diva-20917.

Testo completo

Abstract (sommario):

Forced convection boiling flow, often referred to as two-phase flow, is a common phenomenon which occurs in many industrial processes. The relationship between the total pressure drop in a channel containing two-phase flow and the mass flux of the flow is known as the pressure characteristic curve. If any part of pressure characteristic curve contains a negative slope, flow instabilities might occur in the channel. Flow instabilities are unwanted because they can reduce the efficiency of the industrial process. In this study experimental work has been done to analyze the behavior of the pressu

Gli stili APA, Harvard, Vancouver, ISO e altri

4

Ahn, Hee Seok. "Heat transfer enhancement in single-phase forced convection with blockages and in two-phase pool boiling with nano-structured surfaces." Texas A&M University, 2003. http://hdl.handle.net/1969.1/5869.

Testo completo

Abstract (sommario):

The first study researched turbulent forced convective heat (mass) transfer down- stream of blockages with round and elongated holes in a rectangular channel. The blockages and the channel had the same cross section, and a distance equal to twice the channel height separated consecutive blockages. Naphthalene sublimation experiments were conducted with four hole aspect ratios (hole-width-to-height ratios) and two hole-to-blockage area ratios (ratios of total hole cross-sectional area to blockage area). The effects of the hole aspect ratio, for each hole-to-blockage area ratio, on the local hea

Gli stili APA, Harvard, Vancouver, ISO e altri

5

Govinder, Kuvendran. "Theoretical analyses and design, construction and testing of a flow loop for the study of generalised forced and natural convection boiling heat transfer phenomena on typical light-water nuclear reactor fuel pin configurations." Diss., University of Pretoria, 2019. http://hdl.handle.net/2263/71554.

Testo completo

Abstract (sommario):

In a worldwide pursuit for more Accident Tolerant nuclear Fuel (ATF), the quest to obtain and certify alternative nuclear fuel cladding tubes for light-water nuclear power reactors is still a key challenge. One of the facets in this program to develop more ATF is the heat transfer evaluation between the various proposed clad tubes manufactured from suitable replacement materials and the current problematic zirconium-alloy based clad tubes used in nuclear power reactors. For the heat transfer analysis, the accurate measurement of the temperature on the heat transfer surface of heated tubes to b

Gli stili APA, Harvard, Vancouver, ISO e altri

6

Muhr, Laurence. "Étude du procédé de fabrication des graisses au lithium complexe." Vandoeuvre-les-Nancy, INPL, 1993. http://www.theses.fr/1993INPL151N.

Testo completo

Abstract (sommario):

Les procédés de fabrication de graisses de lubrification se sont souvent développés de façon empirique dans l'industrie pétrochimique. Face aux difficultés rencontrées lors du développement de nouveaux produits, une recherche plus fondamentale a été entreprise avec pour objectif d'améliorer la conduite du procédé de fabrication des graisses, dans le cas présent des graisses au lithium complexe. Dans un premier temps, une étude critique et explicative du procédé a été réalisée afin d'identifier les séquences susceptibles d'influer fortement sur la qualité du produit final. Il s'est avéré qu'une

Gli stili APA, Harvard, Vancouver, ISO e altri

7

Sun, Guang. "Heat transfer in forced convective flow boiling." Thesis, Imperial College London, 1996. http://hdl.handle.net/10044/1/11255.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

8

Kandlbinder, Thomas. "Experimental investigation of forced convective boiling of hydrocarbons and hydrocarbon mixtures." Thesis, Imperial College London, 1998. http://hdl.handle.net/10044/1/7918.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

9

Ahmad, Masroor. "Critical heat flux and associated phenomena in forced convective boiling in nuclear systems." Thesis, Imperial College London, 2012. http://hdl.handle.net/10044/1/9181.

Testo completo

Abstract (sommario):

In evaporation of a liquid flowing in a tube or nuclear fuel element, there exists a transition (known as "dryout", "burnout", "boiling crisis" or "critical heat flux", CHF) from a high heat transfer coefficient regime to one of greatly reduced heat transfer coefficient. The conditions leading to dryout or CHF and the behaviour of wall temperatures in the ("post dryout or post CHF") region beyond it are of immense importance in nuclear reactor safety. In a nuclear reactor, the clad temperature excursion in the post-dryout region may be unacceptably high and the prediction of the location of dr

Gli stili APA, Harvard, Vancouver, ISO e altri

10

Kiameh, Bassam Philip. "Prediction of critical heat flux (CHF) for non-aqueous fluids in forced convective boiling." Thesis, University of Ottawa (Canada), 1986. http://hdl.handle.net/10393/21731.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

Libri sul tema "Forced convection boiling"

1

A study of forced convection boiling under reduced gravity: Final report. Cleveland, Ohio: National Aeronautics and Space Administration, Lewis Research Center, 1991.

Cerca il testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

2

L, Linne Diane, Rousar Donald C, and United States. National Aeronautics and Space Administration., eds. Forced convection boiling and critical heat flux of ethanol in electrically heated tube tests. [Cleveland, Ohio]: National Aeronautics and Space Administration, Lewis Research Center, 1998.

Cerca il testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

Capitoli di libri sul tema "Forced convection boiling"

1

Kolev, Nikolay Ivanov. "Forced convection boiling." In Multiphase Flow Dynamics 3, 213–43. Berlin, Heidelberg: Springer Berlin Heidelberg, 2011. http://dx.doi.org/10.1007/978-3-642-21372-4_10.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

2

Herwig, Heinz. "Strömungssieden (forced convection boiling)." In Wärmeübertragung A-Z, 226–30. Berlin, Heidelberg: Springer Berlin Heidelberg, 2000. http://dx.doi.org/10.1007/978-3-642-56940-1_51.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

3

Zohar, Yitshak. "Steady, Forced Convection Boiling in Micro Ducts." In Heat Convection in Micro Ducts, 99–130. Boston, MA: Springer US, 2003. http://dx.doi.org/10.1007/978-1-4757-3607-6_7.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

4

Yu, Wenhua, David M. France, and Jules L. Routbort. "Forced Convective Boiling of Ethylene Glycol/Water Mixtures Inside a Small Tube." In Film and Nucleate Boiling Processes, 376–401. 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959: ASTM International, 2011. http://dx.doi.org/10.1520/stp49346t.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

5

Yu, Wenhua, David M. France, and Jules L. Routbort. "Forced Convective Boiling of Ethylene Glycol/Water Mixtures Inside a Small Tube." In Film and Nucleate Boiling Processes, 376–401. 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959: ASTM International, 2011. http://dx.doi.org/10.1520/stp153420120017.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

6

Mohammed Shah, Mirza. "Forced Convection Subcooled Boiling." In Two-Phase Heat Transfer, 123–49. ASME-Wiley, 2021. http://dx.doi.org/10.1115/1.862tht_ch4.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

7

Wang, Tien-Chen, Trevor J. Snyder, and Jacob N. Chung. "Forced-Convection Subcooled Nucleate Boiling and its Application in Microgravity." In Convective Flow Boiling, 111–16. CRC Press, 2019. http://dx.doi.org/10.1201/9780367812089-12.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

8

Yokoya, Sadao, Makoto Watanabe, and Masahiro Shoji. "Upstream Chf of Forced Convection Boiling in an Uniformly Heated Vertical Tube." In Convective Flow Boiling, 201–6. CRC Press, 2019. http://dx.doi.org/10.1201/9780367812089-26.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

9

Shirakawa, Noriyuki, Hideki Horie, and Yuichi Yamamoto. "Analysis of the forced convection boiling with the particle interaction method." In Computational Fluid and Solid Mechanics, 1373–75. Elsevier, 2001. http://dx.doi.org/10.1016/b978-008043944-0/50920-3.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

10

Thome, John R., and Andrea Cioncolini. "Forced Convective Boiling." In Encyclopedia of Two-Phase Heat Transfer and Flow I, 177–218. WORLD SCIENTIFIC, 2015. http://dx.doi.org/10.1142/9789814623216_0024.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

Atti di convegni sul tema "Forced convection boiling"

1

Kurul, N., and Michael Z. Podowski. "MULTIDIMENSIONAL EFFECTS IN FORCED CONVECTION SUBCOOLED BOILING." In International Heat Transfer Conference 9. Connecticut: Begellhouse, 1990. http://dx.doi.org/10.1615/ihtc9.40.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

2

Peng, Xiao-Feng, and Bu-Xuan Wang. "FORCED-CONVECTION AND BOILING CHARACTERISTICS IN MICROCHANNELS." In International Heat Transfer Conference 11. Connecticut: Begellhouse, 1998. http://dx.doi.org/10.1615/ihtc11.2820.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

3

Baummer, Thomas B., Ebrahim Al-Hajri, Michael M. Ohadi, and Serguei V. Dessiatoun. "Forced Convection Boiling in Microchannels for Improved Heat Transfer." In ASME 4th International Conference on Nanochannels, Microchannels, and Minichannels. ASMEDC, 2006. http://dx.doi.org/10.1115/icnmm2006-96215.

Testo completo

Abstract (sommario):

This paper presents experimental results from research investigating the heat transfer capabilities of microchannel surfaces using a novel force-fed boiling and evaporation technique. The evaporative surfaces being investigated consist of a series of parallel, high-aspect ratio, open topped microchannels. The different sample surfaces vary in channel density, channel aspect ratio, and channel width and have heat transfer surface areas up to ten times their nominal surface areas. Liquid enters the channels of the evaporative surface from above through a developed system of feed channels. This m

Gli stili APA, Harvard, Vancouver, ISO e altri

4

Lebaigue, Dr Olivier, C. Colin, and A. Larue de Tournemine. "FORCED CONVECTION BOILING AND CONDENSATION OF AMMONIA IN MICROGRAVITY." In Annals of the Assembly for International Heat Transfer Conference 13. Begell House Inc., 2006. http://dx.doi.org/10.1615/ihtc13.p12.250.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

5

Situ, Rong, Ye Mi, Xiaodong Sun, Mamoru Ishii, and Michitrugu Mori. "Bubble Lift-Off Size in Forced Convection Subcooled Boiling." In ASME 2003 Heat Transfer Summer Conference. ASMEDC, 2003. http://dx.doi.org/10.1115/ht2003-47206.

Testo completo

Abstract (sommario):

Forced convection subcooled boiling experiments were conducted in a BWR-scaled vertical upward annular channel. Water was used as the testing fluid, and the tests were performed at atmospheric pressure. A high-speed digital video camera was applied to capture the dynamics of the bubble nucleation process. Bubble lift-off diameters were obtained from the images for a total of 91 test conditions. A force balance analysis of a growing bubble was carried out. A constitutive relation for bubble lift-off size was obtained by correlating current water data and R113 data from literature. The proposed

Gli stili APA, Harvard, Vancouver, ISO e altri

6

LELAND, J., and L. CHOW. "Forced convection boiling from a non-flush simulated electric chip." In 30th Aerospace Sciences Meeting and Exhibit. Reston, Virigina: American Institute of Aeronautics and Astronautics, 1992. http://dx.doi.org/10.2514/6.1992-251.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

7

Cruces, Roberto, Bernardo Hernández, and Francisco Novas. "Characterization of Boiling Phenomena during Laboratory-Scale Forced Convection Quenching." In The 4th World Congress on Mechanical, Chemical, and Material Engineering. Avestia Publishing, 2018. http://dx.doi.org/10.11159/htff18.159.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

8

Horiuchi, Keisuke, and Shigeo Ohashi. "Forced-Convection Boiling Characteristics Based on Mass and Energy Conservation." In ASME 2007 InterPACK Conference collocated with the ASME/JSME 2007 Thermal Engineering Heat Transfer Summer Conference. ASMEDC, 2007. http://dx.doi.org/10.1115/ipack2007-33471.

Testo completo

Abstract (sommario):

This paper presents an experimental study and theoretical interpretation of two-phase flow in a closed loop. The objective of this work is to find the optimum flow rate with respect to the thermal design power (amount of heat to be rejected). We assume that forced-convection boiling characteristics are explained based on mass and energy conservation, and claim that our proposed coefficient (C ≡ QL / Q : a ratio of amount of evaporated liquid to the flow rate) indicates the optimum flow rate for wide variation of evaporator-shapes and working fluids. In order to verify our model, we have measur

Gli stili APA, Harvard, Vancouver, ISO e altri

9

Aziz, S., Geoffrey F. Hewitt, and D. B. R. Kenning. "HEAT TRANSFER REGIMES IN FORCED-CONVECTION FILM BOILING ON SPHERES." In International Heat Transfer Conference 8. Connecticut: Begellhouse, 1986. http://dx.doi.org/10.1615/ihtc8.700.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

10

Maulbetsch, John S., and Peter Griffith. "SYSTEM-INDUCED INSTABILITIES IN FORCED CONVECTION FLOWS WITH SUBCOOLED BOILING." In International Heat Transfer Conference 3. Connecticut: Begellhouse, 2019. http://dx.doi.org/10.1615/ihtc3.540.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

Rapporti di organizzazioni sul tema "Forced convection boiling"

1

Gehrke, V., and S. G. Bankoff. Stability of forced-convection subcooled boiling in steady-state and transient annular flow. Office of Scientific and Technical Information (OSTI), June 1993. http://dx.doi.org/10.2172/10194741.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

2

Dorra, H., S. C. Lee, and S. G. Bankoff. A critical review of predictive models for the onset of significant void in forced-convection subcooled boiling. Office of Scientific and Technical Information (OSTI), June 1993. http://dx.doi.org/10.2172/10194563.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

3

Wong, Christopher F. A computer code for calculating subcooled boiling pressure drop in forced convective tube flows. Office of Scientific and Technical Information (OSTI), December 1988. http://dx.doi.org/10.2172/5910189.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

Offriamo sconti su tutti i piani premium per gli autori le cui opere sono incluse in raccolte letterarie tematiche. Contattaci per ottenere un codice promozionale unico!