Letteratura scientifica selezionata sul tema "Walls Design and construction"

Cita una fonte nei formati APA, MLA, Chicago, Harvard e in molti altri stili

Scegli il tipo di fonte:

Consulta la lista di attuali articoli, libri, tesi, atti di convegni e altre fonti scientifiche attinenti al tema "Walls Design and construction".

Accanto a ogni fonte nell'elenco di riferimenti c'è un pulsante "Aggiungi alla bibliografia". Premilo e genereremo automaticamente la citazione bibliografica dell'opera scelta nello stile citazionale di cui hai bisogno: APA, MLA, Harvard, Chicago, Vancouver ecc.

Puoi anche scaricare il testo completo della pubblicazione scientifica nel formato .pdf e leggere online l'abstract (il sommario) dell'opera se è presente nei metadati.

Articoli di riviste sul tema "Walls Design and construction"

1

Massone, Leonardo M., Patricio Bonelli, René Lagos, Carl Lüders, Jack Moehle, and John W. Wallace. "Seismic Design and Construction Practices for RC Structural Wall Buildings." Earthquake Spectra 28, no. 1_suppl1 (June 2012): 245–56. http://dx.doi.org/10.1193/1.4000046.

Testo completo
Abstract (sommario):
Reinforced concrete buildings utilizing structural walls for lateral load resistance are the predominant form of construction in Chile for buildings over four stories. Typical buildings include a large number of walls, with ratios of wall cross-sectional area to floor plan area of roughly 3% in each principal direction. Based on the good performance of RC buildings in the March 1985 earthquake, requirements for closely spaced transverse reinforcement at wall boundaries were excluded when Chile adopted a new concrete code in 1996 based on ACI 318-95. In recent years, use of three-dimensional li
Gli stili APA, Harvard, Vancouver, ISO e altri
2

Day, Robert W. "Design and Construction of Cantilevered Retaining Walls." Practice Periodical on Structural Design and Construction 2, no. 1 (February 1997): 16–21. http://dx.doi.org/10.1061/(asce)1084-0680(1997)2:1(16).

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
3

Khalili, Mitra, Sanaz Amindeldar, and Houriye Mashhadibagher Moakhar. "Reusing Plastic Bottles in Energy-Saving Design and Construction." Advanced Materials Research 689 (May 2013): 316–19. http://dx.doi.org/10.4028/www.scientific.net/amr.689.316.

Testo completo
Abstract (sommario):
This paper investigates the use of irresolvable and permanent garbage in environment to build an energy saving wall in cold and hot climatic conditions. The wall is mainly constructed from plastic bottles which provide lightness. The bottles, filled with water to store solar energy, are confined between two walls and able to provide wall stability. Transparent twin wall poly carbonate sheets have been selected as the external surface in order to let the bottles receive solar energy. The inner layer is opaque and fire resistant. A tarpaulin with a reflective inner face is used to prevent heat l
Gli stili APA, Harvard, Vancouver, ISO e altri
4

Garga, Vinod K., and Vince O'Shaughnessy. "Tire-reinforced earthfill. Part 1: Construction of a test fill, performance, and retaining wall design." Canadian Geotechnical Journal 37, no. 1 (February 1, 2000): 75–96. http://dx.doi.org/10.1139/t99-084.

Testo completo
Abstract (sommario):
The satisfactory disposal of scrap tires is a major environmental problem worldwide. This waste occupies valuable space in landfill sites, and tire stockpiles pose serious health and fire hazards. The use of scrap tires as reinforcement for construction of retaining walls and slopes is a viable method towards reduction of this waste. This paper describes the construction of a 57 m high × 17 m wide instrumented test fill, comprising both retaining wall and reinforced slope sections. Approximately 10 000 whole tires and tires with one sidewall removed, tied together with polypropylene rope, were
Gli stili APA, Harvard, Vancouver, ISO e altri
5

Kacálek, Petr, and Tomáš Petříček. "The Structural Design of Wooden Solid Log Wall." MATEC Web of Conferences 279 (2019): 02015. http://dx.doi.org/10.1051/matecconf/201927902015.

Testo completo
Abstract (sommario):
Alternative solutions to joints of outer wooden solid log walls are based on the current situation on the construction market, which reflects general change in attitude towards the environment. Apart from the evaluation of materials and products in accordance with technological and economic aspects, attention is paid to the effect of individual elements on the environment. This trend is reflected in construction practice by a comeback to original materials and expanding designs of residential buildings on the basis of easily renewable material resources, e.g. wood, which is relatively easily a
Gli stili APA, Harvard, Vancouver, ISO e altri
6

Kacálek, Petr, Radim Smolka, and Tomáš Petříček. "Design Properties of Log Walls with Respect to Building Physics." Advanced Materials Research 1041 (October 2014): 288–92. http://dx.doi.org/10.4028/www.scientific.net/amr.1041.288.

Testo completo
Abstract (sommario):
The paper deals with the construction of walls of log wood houses of Canadian type in terms of thermal insulation, with the focus shifted onto the comparison of alternative structural solutions of such walls. The main aim of the research done was to assess the different Canadian type massive log wood walls, with various thermally insulating materials placed between the logs. The computer simulations of wall models were done in ANSYS software. Massive wooden walls unfortunately do hardly meet today's ever increasing requirements given for thermal resistance, heat conductivity and heat losses of
Gli stili APA, Harvard, Vancouver, ISO e altri
7

Zhang, Qiao, and Nan Zheng. "Research and Engineering in the Design of Building Walls." Applied Mechanics and Materials 578-579 (July 2014): 527–31. http://dx.doi.org/10.4028/www.scientific.net/amm.578-579.527.

Testo completo
Abstract (sommario):
Modern building walls is no longer a decoration, a simple external maintenance of the structure, but more and more deeply into an organic part of the whole building and involved in the functional construction of the entire building. The impact on the safety and energy saving performance of the whole building has come to a crucial point. A height of 237.7m core tube frame structure actually works in Qingdao cited as an example and the design of high-performance curtain wall system is studied. Many considerations in choosing the design and construction aspects of wall materials,design methods ar
Gli stili APA, Harvard, Vancouver, ISO e altri
8

Das, Prabir K., Anthony L. Ricci, Huang Ni, and Paul Harrington. "Use of Soldier Pile–Tremie Concrete Slurry Walls as Permanent Tunnel Walls." Transportation Research Record: Journal of the Transportation Research Board 1541, no. 1 (January 1996): 153–62. http://dx.doi.org/10.1177/0361198196154100120.

Testo completo
Abstract (sommario):
The analysis and design of soldier pile–tremie concrete (SPTC) slurry walls for the Massachusetts Highway Department's (MHD) Central Artery/Tunnel (CA/T) Project in downtown Boston are discussed. Unlike most slurry walls, which are used as temporary support for excavation during construction, these SPTC walls are designed also as the permanent wall system for the tunnels. The CA/T includes more than 6.1 km (20,000 ft) of slurry walls. Most of the walls are designed and are to be constructed as SPTC walls. Steel wide-flange soldier piles are installed at 1.21- to 1.83-m (4- to 6-ft) spacings in
Gli stili APA, Harvard, Vancouver, ISO e altri
9

Han, Ze Guang, Xin Fang Song, and Rui Qin Hao. "The Assembled Structure Analysis of Energy Conservation and Material Saving Unit Sheet Aluminum Curtain Wall." Advanced Materials Research 243-249 (May 2011): 6165–68. http://dx.doi.org/10.4028/www.scientific.net/amr.243-249.6165.

Testo completo
Abstract (sommario):
The joint between all plains in unit sheet aluminum curtain wall which is hanged on main body architecture is plugboard combination. The change of ambient temperature and wind load generates the change of expansion joints, which are the performance index of curtain wall required gas and water tightness, among curtain walls and suspension members. Thus obtained value of expansion joint among curtain walls is very important to guide the curtain wall’s installation. Here, an assemble structure model of curtain wall has firstly been established, the changing law of expansion joints among curtain w
Gli stili APA, Harvard, Vancouver, ISO e altri
10

Liu, Jin Sheng, and Shi Mei Liu. "Several Written Instructions of the Technical Regulation of Shot-Pier Shear Wall Structure Key Figures Construction." Advanced Materials Research 255-260 (May 2011): 747–51. http://dx.doi.org/10.4028/www.scientific.net/amr.255-260.747.

Testo completo
Abstract (sommario):
As a new type of resist lateral force structure, short-pier shear wall structure has been widely used in high-rise and super-tall residential construction. However, at present, there isn’t a specifically targeted short-leg walls structure design and construction technical regulations both at home and abroad, which led to the architectural engineering design and construction market turmoil. By the prophase research of the short-leg walls structure seismic performance, and a great deal of experiments, combine with the latest research results at home and abroad, adopt the limit state design metho
Gli stili APA, Harvard, Vancouver, ISO e altri
Più fonti

Tesi sul tema "Walls Design and construction"

1

Cheung, Kwong-chung. "Reinforced earth wall design & construction in northern access road for Cyberport Development /." View the Table of Contents & Abstract, 2005. http://sunzi.lib.hku.hk/hkuto/record/B3676288X.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
2

Lim, Chim Chai. "Analysis, design, and construction of tilt-up wall panel." Thesis, Virginia Tech, 1987. http://hdl.handle.net/10919/45801.

Testo completo
Abstract (sommario):
The idea of tilt-up construction started in America in the early I900’s. In the beginning, this technique was mainly used on structures such as industrial warehouses and factories. However, recent developments and improvements in tilt-up construction technique and accessories have enabled this building method to be applied to many architecturally appealing offices and residential structures. There are many details the design-build team must consider to ensure the success of a tilt-up project. The floor slab must be designed for panel casting and to withstand the loading of the mobile crane w
Gli stili APA, Harvard, Vancouver, ISO e altri
3

Cheung, Kwong-chung, and 張光中. "Reinforced earth wall design & construction in northern access road for Cyberport Development." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2005. http://hub.hku.hk/bib/B45014279.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
4

Camann, Kevin Robert. "Design and Performance of Load Bearing Shear Walls Made from Composite Rice Straw Blocks." DigitalCommons@CalPoly, 2009. https://digitalcommons.calpoly.edu/theses/218.

Testo completo
Abstract (sommario):
Although rice straw and other grains have been used in building since pre-history, in the past two decades, there has been a move to utilize this rapidly renewable, locally available, agricultural byproduct as part of the sustainable construction movement. Up to this point, this has been done by simply stacking up the full straw bales. Stak Block, invented by Oryzatech, Inc., is a modular, interlocking block made of a composite of rice straw and binding agent that serves as an evolution in straw construction. This study investigates the feasibility of using these Stak Blocks as a structura
Gli stili APA, Harvard, Vancouver, ISO e altri
5

Khalil, Ahmed Amir Ghobarah Ahmed. "Rehabilitation of reinforced concrete structural walls using fibre composites /." *McMaster only, 2005.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
6

Riley, Benjamin. "Concrete living walls." Thesis, Lyon, 2018. http://www.theses.fr/2018LYSE2027/document.

Testo completo
Abstract (sommario):
Bâtir de villes face à la surpopulation tout en prenant en compte les changements climatiques, demandera de faire appel à des solutions concrètes pour répondre aux besoins sanitaires, sécuritaires et biophiliques de leurs habitants. Le but de cette thèse est d'évaluer la possibilité d'avoir un système de mur vivant qui soit durable, écologiquement juste, non limité par la localisation et la typologie du bâtiment et plus abordable que les systèmes actuellement disponibles. L'hypothèse de cette thèse est le béton, en raison de sa durabilité, son coût et son ubiquité, a le potential pour être uti
Gli stili APA, Harvard, Vancouver, ISO e altri
7

Reperant, Jefferey John Robert. "Studies of turbulent liquid sheets for protecting IFE reactor chamber first walls." Thesis, Georgia Institute of Technology, 2002. http://hdl.handle.net/1853/18921.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
8

Burroughs, Van Stephan School of the Built Environment UNSW. "Quantitative criteria for the selection and stabilisation of soils for rammed earth wall construction." Awarded by:University of New South Wales. School of the Built Environment, 2001. http://handle.unsw.edu.au/1959.4/17861.

Testo completo
Abstract (sommario):
Modern building procedures and requirements demand that the selection and stabilisation of soils for the purposes of rammed earth construction be better quantified. This study examines the relationships between soil properties, stabiliser treatments, and stabilised strength and density for 111 soil samples taken from sites in New South Wales (Australia), and develops new quantitative criteria for soil assessment, selection, and stabilisation. Laboratory measurements of soil particle size distribution, plasticity, and shrinkage were made for each soil. Various quantities from 0-6 % of lime,
Gli stili APA, Harvard, Vancouver, ISO e altri
9

Spathelf, Christian Alexander. "Assessment of the behaviour factor for the seismic design of reinforced concrete structural walls according to SANS 10160 : part 4." Thesis, Link to the online version, 2008. http://hdl.handle.net/10019/2039.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
10

Garth, John Stuart. "Experimental Investigation of Lateral Cyclic Behavior of Wood-Based Screen-Grid Insulated Concrete Form Walls." PDXScholar, 2014. https://pdxscholar.library.pdx.edu/open_access_etds/1857.

Testo completo
Abstract (sommario):
Insulated concrete forms (ICFs) are green building components that are primarily used for residential wall construction. Unlike most polystyrene based ICF variants, the Faswall ICFs used in these experiments were significantly denser because they were made from recycled wood particles and cement. The current design approach for structures constructed with this type of wall form only allows the designer to consider the contribution of the reinforced concrete cores. Previous research has shown that this approach may be conservative. This project experimentally evaluated the lateral structural re
Gli stili APA, Harvard, Vancouver, ISO e altri
Più fonti

Libri sul tema "Walls Design and construction"

1

Paul, DB, RR Davidson, and NJ Cavalli, eds. Slurry Walls: Design, Construction, and Quality Control. 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959: ASTM International, 1992. http://dx.doi.org/10.1520/stp1129-eb.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
2

Masonry walls: Specification and design. Boston: Butterworth-Heinemann, 1996.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
3

B, Hall, ed. Seawall design. London: Construction Industry Research and Information Association, 1992.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
4

Hendry, A. W. Masonry Wall Construction. London: Taylor & Francis Group Plc, 2004.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
5

Hendry, A. W. Masonry wall construction. London: E. & F. N. Spon, 2000.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
6

1950-, Khalaf F. M., ed. Masonry wall construction. London: Spon Press, 2001.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
7

Beall, Christine. Masonry walls. Upper Saddle River, N.J: Creative Homeowner Press, 1997.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
8

McElroy, William. Fences & retaining walls. Carlsbad, CA: Craftsman Bk. Co., 2012.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
9

McElroy, William. Fences & retaining walls. Carlsbad, CA: Craftsman Book Co., 1990.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
10

service), SpringerLink (Online, ed. Modern Construction Envelopes. Vienna: Springer-Verlag Vienna, 2011.

Cerca il testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
Più fonti

Capitoli di libri sul tema "Walls Design and construction"

1

Hensey, Paul. "Walls and edges." In Construction Detailing for Landscape and Garden Design, 55–103. New York, NY : Routledge, 2019.: Routledge, 2019. http://dx.doi.org/10.4324/9781315642802-4.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
2

Warren, Dene R. "Retaining Walls and Deep Basements." In Civil Engineering Construction Design and Management, 165–85. London: Macmillan Education UK, 1996. http://dx.doi.org/10.1007/978-1-349-13727-5_7.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
3

Vu, Luu Nguyen, and Pahm Quoc Dung. "Double diaphragm wall – Design and construction experience." In Lecture Notes in Civil Engineering, 439–44. Singapore: Springer Singapore, 2019. http://dx.doi.org/10.1007/978-981-15-2184-3_57.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
4

Kontovourkis, Odysseas. "3D Printing Technology Within a Regenerative Construction Framework." In Future City, 245–61. Cham: Springer International Publishing, 2021. http://dx.doi.org/10.1007/978-3-030-71819-0_13.

Testo completo
Abstract (sommario):
Abstract3D printing (3DP) is considered as a promising technology in construction industry due to a number of advantages that among others include fast and accurate construction, as well as elimination of formworks and material waste. Although 3DP technology is at an early stage of adoption in construction industry, its positive contribution towards a more sustainable construction approach is well acknowledged. Nevertheless, various constraints prevent its further establishment that include among others lack of knowledge among construction actors, premature investigation regarding techniques and material properties, as well as limited work on design optimization, cost, and environmental impact performance analysis. This chapter aims to contribute towards this direction by analysing the 3DP cost and environmental impact of a number of brick units, forming walls with different geometrical complexity. Results show that while walls’ complexity is increased, there are no significant changes in cost, global warming and primary energy consumption. In contrast, through the application of traditional construction processes, the result values would have been increased proportionally to the degree of complexity. This proves the potential of applying the 3DP technique to the construction of any structure at no extra cost and without increasing the environmental impact. Also, it provides an indication of its potential to be included within a regenerative construction framework.
Gli stili APA, Harvard, Vancouver, ISO e altri
5

Nadeem, Abid, Yerzhan Abzhanov, Serik Tokbolat, Mohamad Mustafa, and Bjørn R. Sørensen. "The Impacts of Climate Zone, Wall Insulation, and Window Types on Building Energy Performance." In Design and Construction of Smart Cities, 270–77. Cham: Springer International Publishing, 2021. http://dx.doi.org/10.1007/978-3-030-64217-4_31.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
6

Watts, Andrew. "Walls." In Modern Construction Handbook, 83–199. Vienna: Springer Vienna, 2010. http://dx.doi.org/10.1007/978-3-211-99196-1_3.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
7

Bourahla, N., S. Tafraout, and Y. Bourahla. "Intelligent structural design in BIM platforms: Optimization of RC wall-slab systems." In ECPPM 2021 – eWork and eBusiness in Architecture, Engineering and Construction, 261–67. London: CRC Press, 2021. http://dx.doi.org/10.1201/9781003191476-36.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
8

Tang, Cheng. "Design Principles and Synthesis of 3D Graphene-Analogous Materials and van der Waals Heterostructures." In Construction Principles and Controllable Fabrication of 3D Graphene Materials, 119–37. Singapore: Springer Singapore, 2021. http://dx.doi.org/10.1007/978-981-16-0356-3_5.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
9

Li, Manhai, and Chenguang Ma. "Virtual Simulation Experiment of Curtain Wall Design Based on Behavior Logic of Construction." In Advances in Simulation and Digital Human Modeling, 263–69. Cham: Springer International Publishing, 2021. http://dx.doi.org/10.1007/978-3-030-79763-8_32.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
10

Bailey, H., and D. Hancock. "Construction of Walls." In Brickwork 2 and Associated Studies, 22–27. London: Macmillan Education UK, 1990. http://dx.doi.org/10.1007/978-1-349-11379-8_4.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri

Atti di convegni sul tema "Walls Design and construction"

1

Smith, Jr., Doyle L., and Noel W. Janacek. "The Geotechnical Engineer's Role in Design/Construction of MSE Retaining Walls." In Geo-Frontiers Congress 2011. Reston, VA: American Society of Civil Engineers, 2011. http://dx.doi.org/10.1061/41165(397)352.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
2

Bock, Thomas, Helga Meden, Jana Timmermans, and Ron Unser. "Robot Oriented Design of Reusable Partition Walls with Integrated Building Automation Capabilities." In 21st International Symposium on Automation and Robotics in Construction. International Association for Automation and Robotics in Construction (IAARC), 2004. http://dx.doi.org/10.22260/isarc2004/0065.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
3

Popescu, Cosmin, Gabriel Sas, Thomas Blanksvärd, and Björn Täljsten. "Two-way walls with cut-out openings strengthened by fiber-reinforced polymers." In IABSE Congress, Stockholm 2016: Challenges in Design and Construction of an Innovative and Sustainable Built Environment. Zurich, Switzerland: International Association for Bridge and Structural Engineering (IABSE), 2016. http://dx.doi.org/10.2749/stockholm.2016.1389.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
4

Sabau, Cristian, Cosmin Popescu, Gabriel Sas, Thomas Blanksvärd, and Björn Täljsten. "Monitoring structural behavior of reinforced concrete walls with openings using digital image correlation." In IABSE Congress, Stockholm 2016: Challenges in Design and Construction of an Innovative and Sustainable Built Environment. Zurich, Switzerland: International Association for Bridge and Structural Engineering (IABSE), 2016. http://dx.doi.org/10.2749/stockholm.2016.1808.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
5

Varma, Amit H., Saahastaranshu R. Bhardwaj, and Sanjeev R. Malushte. "Design of SC Walls and Connections in Nuclear Facilities." In 2016 24th International Conference on Nuclear Engineering. American Society of Mechanical Engineers, 2016. http://dx.doi.org/10.1115/icone24-60962.

Testo completo
Abstract (sommario):
Steel-plate composite (SC) walls and associated connections can be designed based on the provisions of Appendix N9 to AISC N690s1. AISC N690s1 is Supplement No. 1 to AISC N690-12 specification for safety related steel structures in nuclear facilities and was published in October 2015. AISC is currently in the process of developing a design guide to further enable the use of this specification. This design guide will explore the provisions of this specification in detail and discuss different possible design methodologies. SC wall details at the beginning of the design process are based on typi
Gli stili APA, Harvard, Vancouver, ISO e altri
6

Scott, P. D., and N. Pickering. "Design and Construction of RPI EMPAC, New York: Foundations and Retaining Walls on a Marginally Stable Slope." In Geo-Denver 2007. Reston, VA: American Society of Civil Engineers, 2007. http://dx.doi.org/10.1061/40903(222)1.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
7

Low, Hin Foo, Sih Ying Kong, and Daniel Kong. "A Review on Prestressed Transfer Plate Analysis and Design." In IABSE Conference, Kuala Lumpur 2018: Engineering the Developing World. Zurich, Switzerland: International Association for Bridge and Structural Engineering (IABSE), 2018. http://dx.doi.org/10.2749/kualalumpur.2018.1037.

Testo completo
Abstract (sommario):
<p>Prestressed transfer plate consists of a thick cast in-situ post-tensioned concrete slab supporting multi-storey shear walls at building transition level. Compared to conventional reinforced concrete transfer beams, it offers savings in concrete volume of 10-15%, cuts steel reinforcement content by 35-50% and significantly reduces formwork usage which eventually helps to achieve lower carbon footprint for a more sustainable transfer floor construction. The design of prestressed transfer plates is complicated owing to its two-way bending behaviour and irregular load path from reactions
Gli stili APA, Harvard, Vancouver, ISO e altri
8

Tatsuoka, Fumio, Masaru Tateyama, Masayuki Koda, and Junichi Koseki. "Seismic Design, Construction and Performance of Geosynthetic-Reinforced Soil Retaining Walls and Bridge Abutments for Railways in Japan." In Geo-Congress 2013. Reston, VA: American Society of Civil Engineers, 2013. http://dx.doi.org/10.1061/9780784412787.116.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
9

Abongo, Kepha, Makoto Kimura, and Akihiro Kitamura. "Design and Construction of Reinforced Steel Chain Wall." In GeoShanghai International Conference 2010. Reston, VA: American Society of Civil Engineers, 2010. http://dx.doi.org/10.1061/41107(380)1.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
10

DiFiore, Scott J., and Bryan P. Strohman. "Look Out Below! Potential Pitfalls and Suggested Improvements in the Design and Construction of Mechanically Stabilized Earth (MSE) Walls." In Sixth Congress on Forensic Engineering. Reston, VA: American Society of Civil Engineers, 2012. http://dx.doi.org/10.1061/9780784412640.068.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri

Rapporti di organizzazioni sul tema "Walls Design and construction"

1

Kochkin, V., and J. Wiehagen. Construction Guide to Next-Generation High-Performance Walls in Climate Zones 3-5 - Part 1: 2x6 Walls. Office of Scientific and Technical Information (OSTI), August 2017. http://dx.doi.org/10.2172/1412978.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
2

Kochkin, V., and J. Wiehagen. Construction Guide to Next-Generation High-Performance Walls in Climate Zones 3-5 - Part 2: 2x4 Walls. Office of Scientific and Technical Information (OSTI), August 2017. http://dx.doi.org/10.2172/1413032.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
3

Kochkin, V., and J. Wiehagen. Construction Guide to Next-Generation High-Performance Walls in Climate Zones 3-5 - Part 1: 2x6 Walls. Office of Scientific and Technical Information (OSTI), August 2017. http://dx.doi.org/10.2172/1398748.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
4

Kochkin, V., and J. Wiehagen. Construction Guide to Next-Generation High-Performance Walls in Climate Zones 3-5 - Part 2: 2x4 Walls. Office of Scientific and Technical Information (OSTI), June 2017. http://dx.doi.org/10.2172/1398753.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
5

Lstiburek, J., K. Ueno, and S. Musunuru. Modeling Enclosure Design in Above-Grade Walls. Office of Scientific and Technical Information (OSTI), March 2016. http://dx.doi.org/10.2172/1245544.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
6

Lstiburek, J., K. Ueno, and S. Musunuru. Modeling Enclosure Design in Above-Grade Walls. Office of Scientific and Technical Information (OSTI), March 2016. http://dx.doi.org/10.2172/1245345.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
7

CORPS OF ENGINEERS WASHINGTON DC. Construction: Design and Construction Evaluation (DCE). Fort Belvoir, VA: Defense Technical Information Center, February 1996. http://dx.doi.org/10.21236/ada404141.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
8

DeRenzis, A., and V. Kochkin. High-R Walls for New Construction Structural Performance. Wind Pressure Testing. Office of Scientific and Technical Information (OSTI), January 2013. http://dx.doi.org/10.2172/1219901.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
9

Arena, Lois B. Construction Guidelines for High R-Value Walls without Exterior Rigid Insulation. Office of Scientific and Technical Information (OSTI), July 2016. http://dx.doi.org/10.2172/1324032.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
10

DeRenzis, A., and V. Kochkin. High-R Walls for New Construction Structural Performance: Wind Pressure Testing. Office of Scientific and Technical Information (OSTI), January 2013. http://dx.doi.org/10.2172/1067930.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
Offriamo sconti su tutti i piani premium per gli autori le cui opere sono incluse in raccolte letterarie tematiche. Contattaci per ottenere un codice promozionale unico!