Gotowe bibliografie tematyczne / Winged blade / Rozprawy doktorskie
Kliknij ten link, aby zobaczyć inne rodzaje publikacji na ten temat: Winged blade.

Rozprawy doktorskie na temat „Winged blade”

Autor: Grafiati
Data publikacji: 2 czerwca 2025
Data aktualizacji: 31 lipca 2025

Utwórz poprawne odniesienie w stylach APA, MLA, Chicago, Harvard i wielu innych

Wybierz rodzaj źródła:

Sprawdź 50 najlepszych rozpraw doktorskich naukowych na temat „Winged blade”.

Przycisk „Dodaj do bibliografii” jest dostępny obok każdej pracy w bibliografii. Użyj go – a my automatycznie utworzymy odniesienie bibliograficzne do wybranej pracy w stylu cytowania, którego potrzebujesz: APA, MLA, Harvard, Chicago, Vancouver itp.

Możesz również pobrać pełny tekst publikacji naukowej w formacie „.pdf” i przeczytać adnotację do pracy online, jeśli odpowiednie parametry są dostępne w metadanych.

Przeglądaj rozprawy doktorskie z różnych dziedzin i twórz odpowiednie bibliografie.

1

Gase, Zachary M. "Below-Rated Control of Swept-Blade Wind Turbines." Scholarly Commons, 2016. https://scholarlycommons.pacific.edu/uop_etds/225.

Pełny tekst źródła
Streszczenie:
Modelling studies have shown that 1.5 and 3.0 MW wind turbines with blade sweep have an increased annual energy production (AEP) of approximately 5% when compared to straight-blade wind turbines. The objective of the research was to further increase below-rated, variable speed, power capture when using swept-blades. When operating in the variable speed region, the turbine’s torque is proportional to the square of the generator speed, and k is the proportionality constant (T = kΩ 2 ). Initial studies indicated that the value of k needed to be lowered from the original value to increase AEP. Thi
Style APA, Harvard, Vancouver, ISO itp.
2

Richards, Phillip W. "Design strategies for rotorcraft blades and HALE aircraft wings applied to damage tolerant wind turbine blade design." Diss., Georgia Institute of Technology, 2014. http://hdl.handle.net/1853/53488.

Pełny tekst źródła
Streszczenie:
Offshore wind power production is an attractive clean energy option, but the difficulty of access can lead to expensive and rare opportunities for maintenance. Smart loads management (controls) are investigated for their potential to increase the fatigue life of damaged offshore wind turbine rotor blades. This study will consider two commonly encountered damage types for wind turbine blades, the trailing edge disbond (bond line failure) and shear web disbond, and show how 3D finite element modeling can be used to quantify the effect of operations and control strategies designed to extend the f
Style APA, Harvard, Vancouver, ISO itp.
3

Sousa, Isaac Diego Pereira de. "Design and testing Of blades for small wind turbines with different geometrical correction in root and tip of blade." Universidade Federal do CearÃ, 2014. http://www.teses.ufc.br/tde_busca/arquivo.php?codArquivo=12320.

Pełny tekst źródła
Streszczenie:
CoordenaÃÃo de AperfeÃoamento de Pessoal de NÃvel Superior<br>The work aims to build , using the BEM (Blade Element Moment) theory , and test three wind rotors , each one consisting of three blades, which were constructed and used for assembling three SWT (Small Wind Turbine) with TSR (Tip Speed Ratio) equal to seven. The three rotors with blades of 2 meters length, distinguished themselves in their geometries as follows: 1) blades without any correction, 2) blades with only tip correction, 3) blades with only root correction. The NREL S809 airfoil developed by the U.S. National Renewable Ener
Style APA, Harvard, Vancouver, ISO itp.
4

Powell, Jonathan Edward. "The application of particle image velocimetry to vortical flow fields." Thesis, Heriot-Watt University, 2000. http://hdl.handle.net/10399/575.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
5

Scott, Nigel William Jackson. "A flexible blade wind turbine for electricity generation." Thesis, Imperial College London, 1997. http://hdl.handle.net/10044/1/7214.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
6

Dubnický, Ladislav. "Aerodynamika axiálních větrných turbín." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2019. http://www.nusl.cz/ntk/nusl-400425.

Pełny tekst źródła
Streszczenie:
Nowadays, the climate change issue is becoming more and more actual in our society. Increase of the average temperature on Earth in a couple of degrees could have catastrophic consequences. One of the possible solutions seems to be renewable energy sources as photovoltaics, biomass of water and wind energy. This thesis deals with the aerodynamics problems of wind energy source. Wind turbines transform kinetic energy of wind to mechanical power. The efficiency is physically limited to 59,26 %, but in reality, it is getting around 45 %. This is caused by three biggest losses inducted in wind tur
Style APA, Harvard, Vancouver, ISO itp.
7

Wu, Daniel. "The Effect of Blade Aeroelasticity and Turbine Parameters on Wind Turbine Noise." Thesis, Virginia Tech, 2017. http://hdl.handle.net/10919/78714.

Pełny tekst źródła
Streszczenie:
In recent years, the demand for wind energy has dramatically increased as well as the number and size of commercial wind turbines. These large turbines are loud and can cause annoyance to nearby communities. Therefore, the prediction of large wind turbine noise over long distances is critical. The wind turbine noise prediction is a very complex problem since it has to account for atmospheric conditions (wind and temperature), ground absorption, un-even terrain, turbine wake, and blade deformation. In these large turbines, the blade deflection is significant and it can potentially influence the
Style APA, Harvard, Vancouver, ISO itp.
8

Walsh, Justin M. "Composite material bend-twist coupling for wind turbine blade applications." Laramie, Wyo. : University of Wyoming, 2009. http://proquest.umi.com/pqdweb?did=1965523621&sid=1&Fmt=2&clientId=18949&RQT=309&VName=PQD.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
9

Thuné, Sebastian, and Torstein Soland. "Investigation Of Different Airfoils on Outer Sections of Large Rotor Blades." Thesis, Mälardalens högskola, Akademin för innovation, design och teknik, 2012. http://urn.kb.se/resolve?urn=urn:nbn:se:mdh:diva-15293.

Pełny tekst źródła
Streszczenie:
Wind power counts for roughly 3 % of the global electricity production. In the chase to produce greener power, much attention lies on getting more electricity from the wind, extraction of kinetic energy, with help of wind turbines. Wind turbines have been used for electricity production since 1887 and have since then developed into more efficient designs and become significantly bigger and with a higher efficiency. The operational conditions change considerably over the rotor length. Inner sections are typically exposed to more complex operational conditions than the outer sections. However, t
Style APA, Harvard, Vancouver, ISO itp.
10

Elfarra, Monier A. K. "Horizontal Axis Wind Turbine Rotor Blade: Winglet And Twist Aerodynamic Design And Optimization Using Cfd." Phd thesis, METU, 2011. http://etd.lib.metu.edu.tr/upload/12612987/index.pdf.

Pełny tekst źródła
Streszczenie:
The main purpose of this study is to aerodynamically design and optimize winglet, twist angle distribution and pitch angle for a wind turbine blade using CFD to produce more power. The RANS solver of Numeca Fine/Turbo was validated by two test cases, the NREL II and NREL VI blades. The results have shown a considerable agreement with measurements for both cases. Two different preconditioners have been implemented for the low Mach number flow. The results have shown the superiority of Merkle preconditioner over Hakimi one and Merkle was selected for further simulations. In addition to that, dif
Style APA, Harvard, Vancouver, ISO itp.
11

Gonzalez, Campos Jose Alberto. "Design and Experimentation of Darrieus Vertical Axis Wind Turbines." Case Western Reserve University School of Graduate Studies / OhioLINK, 2020. http://rave.ohiolink.edu/etdc/view?acc_num=case1594690510943748.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
12

Pierce, Warrick Tait. "Evaluation and performance prediction of a wind turbine blade." Thesis, Stellenbosch : University of Stellenbosch, 2009. http://hdl.handle.net/10019.1/1791.

Pełny tekst źródła
Streszczenie:
Thesis (MScEng (Mechanical and Mechatronic Engineering))--University of Stellenbosch, 2009.<br>The aerodynamic performance of an existing wind turbine blade optimised for low wind speed conditions is investigated. The aerodynamic characteristics of four span locations are determined from surface pressure measurements and wake surveys with a traversed five-hole probe performed in a low speed wind tunnel for chord Reynolds numbers ranging from 360,000 - 640,000. Two-dimensional modelling of the wind tunnel tests is performed with the commercial computational fluid dynamics code FLUENT. The
Style APA, Harvard, Vancouver, ISO itp.
13

Carpenter, Laura E. "The Design and Experimental Investigation of Novel Double-blade Wind Turbine Models Inspired by Houck's Concept." Wright State University / OhioLINK, 2016. http://rave.ohiolink.edu/etdc/view?acc_num=wright1482494647404864.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
14

Kleinknecht, Mathias, and Álvarez Alfredo Fernández. "Wind turbine blade modeling - setting out from experimental data." Thesis, Linnéuniversitetet, Institutionen för maskinteknik (MT), 2013. http://urn.kb.se/resolve?urn=urn:nbn:se:lnu:diva-26054.

Pełny tekst źródła
Streszczenie:
Complex systems can be divided into simpler substructures. Determining the properties of each subcomponent by experimental procedures is practical and can serve to verify or calibrate finite element models. In this work, an existing model of a wind turbine blade was improved by use of experimental data. Such a blade is a subpart of a complete wind turbine. For calibration purpose, several material tests were made in order to determine the stiffness and mass properties. Later on, vibration tests of the blades were conducted and compared with simulation results of the improved model. Geometry va
Style APA, Harvard, Vancouver, ISO itp.
15

Baldassarre, Alessandro. "FEM and experimental analysis of a wind turbine blade." Master's thesis, Alma Mater Studiorum - Università di Bologna, 2015. http://amslaurea.unibo.it/8533/.

Pełny tekst źródła
Streszczenie:
This paperwork compares the a numerical validation of the finite element model (FEM) with respect the experimental tests of a new generation wind turbine blade designed by TPI Composites Inc. called BSDS (Blade System Design Study). The research is focused on the analysis by finite element (FE) of the BSDS blade and its comparison with respect the experimental data from static and dynamic investigations. The goal of the research is to create a general procedure which is based on a finite element model and will be used to create an accurate digital copy for any kind of blade. The blade prototyp
Style APA, Harvard, Vancouver, ISO itp.
16

Bose, Anushika. "Birds & Blades." Doctoral thesis, Humboldt-Universität zu Berlin, 2021. http://dx.doi.org/10.18452/22458.

Pełny tekst źródła
Streszczenie:
Kollisionen von Vögeln mit Windturbinen haben sich zu einer bedenklichen Quelle für die Gefährdung besonders von Populationen seltenerer Vogelarten entwickelt. Allerdings wird im Allgemeinen auch bestätigt, dass die Nutzung der Windenergie unverzichtbar ist. Das Hauptziel dieser Arbeit war es, die Relevanz der Wechselwirkungen zu verstehen, die zwischen technischen Infrastrukturen und den von Kollisionen betroffenen Vogelarten auf der Landschaftsebene stattfinden. Da sowohl von der Landschaft beeinflusst werden. Unter Nutzung der durch gezielte Nachsuche gefundenen Opfer der am häufigsten von
Style APA, Harvard, Vancouver, ISO itp.
17

Mohammadi, Mohammad Mehdi. "PREDICTION OF WIND TURBINE BLADE FATIGUE LOADS USING FEED-FORWARD NEURAL NETWORKS." Thesis, Uppsala universitet, Institutionen för geovetenskaper, 2021. http://urn.kb.se/resolve?urn=urn:nbn:se:uu:diva-444115.

Pełny tekst źródła
Streszczenie:
In recent years, machine learning applications have gained great attention in the wind power industry. Among these, artificial neural networks have been utilized to predict the fatigue loads of wind turbine components such as rotor blades. However, the limited number of contributions and differences in the used databases give rise to several questions which this study has aimed to answer. Therefore, in this study, 5-min SCADA data from the Lillgrund wind farm has been used to train two feed-forward neural networks to predict the fatigue loads at the blade root in flapwise and edgewise directio
Style APA, Harvard, Vancouver, ISO itp.
18

Rahnama, Behzad. "Reduction of Environmental Impact Effect of Disposing Wind Turbine Blades." Thesis, Högskolan på Gotland, Institutionen för kultur, energi och miljö, 2011. http://urn.kb.se/resolve?urn=urn:nbn:se:uu:diva-217000.

Pełny tekst źródła
Streszczenie:
Wind power industry is expected to be one of the fastest growing renewable energy sources inthe world. The growth specially focuses on growing industries and markets, because ofeconomical condition for wind power development besides political decisions.According to growth of wind turbine industries, wind turbine blades are growing fast in both sizeand number. The problem that now arises is how to deal with the blades at the end of their lifecycle. This Master Thesis describes existing methods of disposing wind turbine blades.Moreover, the thesis considers alternative method of disposing blades
Style APA, Harvard, Vancouver, ISO itp.
19

Edwards, Bryan Kyle. "COMPOSITE MANUFACTURING OF SMALL WIND TURBINE BLADES- UTILITY SCALE METHODS APPLIED TO SMALL WIND." DigitalCommons@CalPoly, 2009. https://digitalcommons.calpoly.edu/theses/175.

Pełny tekst źródła
Streszczenie:
Cal Poly, San Luis Obispo’s first wind turbine explores the methods and processes that are employed to manufacture utility scale wind turbines, and applies them to small scale wind turbines. The primary objective is to promote the development of small scale wind turbine blades in ways that resemble, as closely as possible, the construction and methods of utility scale turbine blade manufacturing. Vacuum infusion is employed to create a hollow, multi piece, lightweight design using carbon fiber and fiberglass with an epoxy based resin. A “rapid prototyping” method is developed using high de
Style APA, Harvard, Vancouver, ISO itp.
20

Ingersoll, Bryce Taylor. "Efficient Incorporation of Fatigue Damage Constraints in Wind Turbine Blade Optimization." BYU ScholarsArchive, 2018. https://scholarsarchive.byu.edu/etd/6985.

Pełny tekst źródła
Streszczenie:
Improving the wind turbine blade design has a significant effect on the efficiency of the wind turbine. This is a challenging multi-disciplinary optimization problem. During the blade design process, the aerodynamic shapes, sizing of the structural members, and material composition must all be determined and optimized. Some previous blade design methods incorporate the wind turbine's static response with an added safety factor to account for neglected dynamic effects. Others incorporate the dynamic response, but in general is limited to a few design cases. By not fully incorporating the dynam
Style APA, Harvard, Vancouver, ISO itp.
21

Liu, Pu. "Reducing the environmental impact of wind turbine blades." Thesis, University of Cambridge, 2017. https://www.repository.cam.ac.uk/handle/1810/270347.

Pełny tekst źródła
Streszczenie:
Wind energy, one of the most promising sources of clean energy, has developed rapidly over the last two decades. Wind turbines (WT) are arguably clean during operation, offering minimal pollution and zero CO2 emissions, but significant amounts of energy are used and CO2 emitted during their manufacture, and, furthermore, the turbines are environmentally problematic at end-of-life (EoL), especially the blades. WT blades are mainly made with composite materials comprising thermosetting resin and glass fibre. They are lightweight and strong but problematic to recycle. Large volumes of waste will
Style APA, Harvard, Vancouver, ISO itp.
22

Pitchford, Corey. "Impedance-Based Structural Health Monitoring of Wind Turbine Blades." Thesis, Virginia Tech, 2007. http://hdl.handle.net/10919/34946.

Pełny tekst źródła
Streszczenie:
Wind power is a fast-growing source of non-polluting, renewable energy with vast potential. However, current wind technology must be improved before the potential of wind power can be fully realized. One of the key components in improving wind turbines is their blades. Blade failure is very costly because blade failure can damage other blades, the wind turbine itself, and possibly other wind turbines. A successful structural health monitoring (SHM) system incorporated into wind turbines could extend blade life and allow for less conservative designs. Impedance-based SHM is a method wh
Style APA, Harvard, Vancouver, ISO itp.
23

Nosti, Christopher James. "PERFORMANCE ANALYSIS AND LIFE PREDICTION FOR SMALL WIND TURBINE BLADES: A WOOD LAMINATE CASE STUDY." DigitalCommons@CalPoly, 2009. https://digitalcommons.calpoly.edu/theses/154.

Pełny tekst źródła
Streszczenie:
A detailed study of the fatigue life of wooden wind turbine blades for a new 10 kilowatt system was undertaken. A numerical model of the blades was created using the technical software package MATLAB in order to estimate the maximum stress occurring within the blade in response to changes in wind velocities based on a wind profile approximating the location where these turbines are expected to operate. The material properties of the wooden laminate were measured using an Instron tensile test machine and were found to be in line with published values. In parallel with this effort, a three di
Style APA, Harvard, Vancouver, ISO itp.
24

Flood, Robert C. "Vibrations of an isolated wind turbine blade using the finite element method." Thesis, Virginia Polytechnic Institute and State University, 1986. http://hdl.handle.net/10919/91089.

Pełny tekst źródła
Streszczenie:
The finite element method is applied to an isolated and twisted wind turbine blade which is rotating in a vertical plane to determine its structural dynamic characteristics. The equations of motion are formulated for a rotating beam with flap and lead-lag degrees of freedom subjected to nonsymmetric bending. Using a variational approach, a blade finite clement is developed from these equations of motion. Additionally, expressions are formulated for the elastic strain energy and kinetic energy of a rotating wind turbine blade. Lagrange's equation is applied to these energy expressions and an is
Style APA, Harvard, Vancouver, ISO itp.
25

Perry, Dylan R. "AERODYNAMIC DESIGN AND STRUCTURAL ANALYSIS PROCEDURE FOR SMALL HORIZONTAL-AXIS WIND TURBINE ROTOR BLADE." DigitalCommons@CalPoly, 2015. https://digitalcommons.calpoly.edu/theses/1375.

Pełny tekst źródła
Streszczenie:
This project accomplished two correlated goals of designing a new rotor blade to be used with the Cal Poly Wind Power Research Center, as well as defining the methodology required for the aerodynamic analysis of an optimized blade, the procedure required for generation of an accurate CAD model for the new blade geometry, and structural integrity verification procedure for the new blade via finite element analysis under several operating scenarios. The new rotor blades were designed to perform at peak efficiency at a much lower wind speed than the current CPWPRC rotor blades and incorporated a
Style APA, Harvard, Vancouver, ISO itp.
26

Cencelli, Nicolette Arnalda, Bakstrom T. W. Von, and T. S. A. Denton. "Aerodynamic optimisation of a small-scale wind turbine blade for low windspeed conditions." Thesis, Stellenbosch : Stellenbosch University, 2006. http://hdl.handle.net/10019.1/353.

Pełny tekst źródła
Streszczenie:
Thesis (MScEng (Department of Mechanical and Mechatronic Engineering))--Stellenbosch University, 2006.<br>ENGLISH ABSTRACT: Wind conditions in South Africa determine the need for a small-scale wind turbine to produce useable power at windspeeds below 7m/s. In this project, a range of windspeeds, within which optimal performance o the wind turbine is expected, was selected. The optimal performance was assessed in terms of the Coefficient of Power(Cp), which rates the turbines blade's ability to extract energy form the avalible wind stream. The optimisation methods employed allowed a means of
Style APA, Harvard, Vancouver, ISO itp.
27

Duran, Serhat. "Computer-aided Design Of Horizontal-axis Wind Turbine Blades." Master's thesis, METU, 2005. http://etd.lib.metu.edu.tr/upload/12605790/index.pdf.

Pełny tekst źródła
Streszczenie:
Designing horizontal-axis wind turbine (HAWT) blades to achieve satisfactory levels of performance starts with knowledge of the aerodynamic forces acting on the blades. In this thesis, HAWT blade design is studied from the aspect of aerodynamic view and the basic principles of the aerodynamic behaviors of HAWTs are investigated. Blade-element momentum theory (BEM) known as also strip theory, which is the current mainstay of aerodynamic design and analysis of HAWT blades, is used for HAWT blade design in this thesis. Firstly, blade design procedure for an optimum rotor according to BEM theory i
Style APA, Harvard, Vancouver, ISO itp.
28

Ning, Zhe. "An Experimental Investigation on the Control of Tip Vortices from Wind Turbine Blade." Wright State University / OhioLINK, 2013. http://rave.ohiolink.edu/etdc/view?acc_num=wright1376658342.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
29

Chinchore, Asmita C. "Computational Study of Savonius Wind Turbine." Cleveland State University / OhioLINK, 2013. http://rave.ohiolink.edu/etdc/view?acc_num=csu1389795972.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
30

Karaolis, Nicos M. "The design of fibre reinforced composite blades for passive and active wind turbine rotor aerodynamic control." Thesis, University of Reading, 1989. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.235661.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
31

Peesapati, Vidyadhar. "Lightning protection of wind turbines." Thesis, University of Manchester, 2010. https://www.research.manchester.ac.uk/portal/en/theses/lightning-protection-of-wind-turbines(e710c763-840e-4b76-b7a5-0d006c4e0983).html.

Pełny tekst źródła
Streszczenie:
Wind turbines are the largest contributor to renewable energy both in Britain and the rest of Europe. With a rise in the installed capacity and an increase in offshore wind energy due to governments green targets by 2020, there has been a large development in new wind turbines for optimized performance. The present thesis deals with the uncertainties in regards to the lightning phenomenon on wind turbines with emphasis on the rotor blades. Rotor blades are the most expensive part to replace in the event of lightning related damage. The research presents results based on lightning data analysis
Style APA, Harvard, Vancouver, ISO itp.
32

Al, Kaysee Ahmed, and Marek Wronski. "Dynamic Substructuring of an A600 Wind Turbine." Thesis, Linnéuniversitetet, Institutionen för maskinteknik (MT), 2014. http://urn.kb.se/resolve?urn=urn:nbn:se:lnu:diva-36194.

Pełny tekst źródła
Streszczenie:
A limited and extendable master thesis is representing the first step in the experimental substructuring of an A600 wind turbine. Additional masses have been designed, manufactured and added to the sub components for the laboratory experimental tests. Further preparations for dynamic experimental tests have been described and implemented. Vibrational tests of a modified wind turbine blade have been made using the Leuven Measurements System (LMS) for excitations and data acquisition purposes. The theory of frequency response function based substructuring applied on the wind turbine blade model
Style APA, Harvard, Vancouver, ISO itp.
33

Ha, Kwangtae. "A Combined Piezoelectric Composite Actuator and Its Application to Wing/Blade Tips." Diss., Georgia Institute of Technology, 2005. http://hdl.handle.net/1853/7575.

Pełny tekst źródła
Streszczenie:
A novel combined piezoelectric-composite actuator configuration is proposed and analytically modeled in this work. The actuator is a low complexity, active compliant mechanism obtained by coupling a modified star cross sectional configuration composite beam with a helicoidal bimorph piezoelectric actuator coiled around it. This novel actuator is a good candidate as a hinge tension-torsion bar actuator for a helicopter rotor blade flap or blade tip and mirror rotational positioning. In the wing tip case, the tip deflection angle is different only according to the aerodynamic moment depending
Style APA, Harvard, Vancouver, ISO itp.
34

Hajdaei, Amirhossein. "Extending the fatigue life of a T-joint in a composite wind turbine blade." Thesis, University of Manchester, 2014. https://www.research.manchester.ac.uk/portal/en/theses/extending-the-fatigue-life-of-a-tjoint-in-a-composite-wind-turbine-blade(f9fb5741-c97e-466b-84bc-53316cfbecf2).html.

Pełny tekst źródła
Streszczenie:
Wind turbines are classic examples of structures where their operating lifetime is controlled by the fatigue properties of the material. This is exacerbated by the 2D nature of the composite materials used in blade construction which are typically fabrics in a variety of formats (e.g. non crimp fabrics, uniweave, woven). The formation of internal detailed shapes within the blade, allowing features such as spars, shear webs and other connections, inevitably requires these 2D material configurations to be formed into 3D shapes. This introduces positions within the structure where load transfer o
Style APA, Harvard, Vancouver, ISO itp.
35

Esu, Ozak O. "Vibration-based condition monitoring of wind turbine blades." Thesis, Loughborough University, 2016. https://dspace.lboro.ac.uk/2134/21679.

Pełny tekst źródła
Streszczenie:
Significant advances in wind turbine technology have increased the need for maintenance through condition monitoring. Indeed condition monitoring techniques exist and are deployed on wind turbines across Europe and America but are limited in scope. The sensors and monitoring devices used can be very expensive to deploy, further increasing costs within the wind industry. The work outlined in this thesis primarily investigates potential low-cost alternatives in the laboratory environment using vibration-based and modal testing techniques that could be used to monitor the condition of wind turbin
Style APA, Harvard, Vancouver, ISO itp.
36

Chromec, Tomáš. "Aerodynamický návrh větrné turbíny pro zvolenou lokalitu." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2014. http://www.nusl.cz/ntk/nusl-231651.

Pełny tekst źródła
Streszczenie:
This master‘s thesis focuses on wind turbines. The first part describes the basic attributes of wind energy and wind turbines and is accompanied by a many images. The next section is a statistical processing of measured meteorological data from measuring stations of the Czech Hydrometeorological Institute. These data are then used for calculations of the blades of wind turbines. The calculations are carried by two different methods. The first method is called the blade element momentum theory, the second method is the theory of blade cascade. Using these methods are obtained by two different b
Style APA, Harvard, Vancouver, ISO itp.
37

Andersen, Brett. "A Comparison of Two and Three Bladed Floating Wind Turbines." University of Toledo / OhioLINK, 2010. http://rave.ohiolink.edu/etdc/view?acc_num=toledo1271883552.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
38

Ali, Muhammad Anttho. "In-cloud ice accretion modeling on wind turbine blades using an extended Messinger model." Thesis, Georgia Institute of Technology, 2015. http://hdl.handle.net/1853/53870.

Pełny tekst źródła
Streszczenie:
Wind turbines often operate under cold weather conditions where icing may occur. Icing causes the blade sections to stall prematurely reducing the power production at a given wind speed. The unsteady aerodynamic loads associated with icing can accelerate blade structural fatigue and creates safety concerns. In this work, the combined blade element-momentum theory is used to compute the air loads on the baseline rotor blades, prior to icing. At each blade section, a Lagrangian particle trajectory model is used to model the water droplet trajectories and their impact on the blade surface. An ext
Style APA, Harvard, Vancouver, ISO itp.
39

Bhattarai, Kripesh. "On the Use of a Digital Communication Channel for Feedback in a Position Control System." University of Akron / OhioLINK, 2012. http://rave.ohiolink.edu/etdc/view?acc_num=akron1353512595.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
40

Chen, Yng-Ru. "CHARACTERIZATION OF CUP ANEMOMETER DYNAMICS AND CALCULATION OF THE ACOUSTIC NOISE PRODUCED BY A NREL PHASE VI WIND TURBINE BLADE." Case Western Reserve University School of Graduate Studies / OhioLINK, 2016. http://rave.ohiolink.edu/etdc/view?acc_num=case1459427530.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
41

Abdulqadir, Sherwan Ahmed. "Turbulence modelling for horizontal axis wind turbine rotor blades." Thesis, University of Manchester, 2017. https://www.research.manchester.ac.uk/portal/en/theses/turbulence-modeling-for-horizontal-axis-wind-turbine-rotor-blades(2536b213-3a0c-4977-ac39-916a9fce98d2).html.

Pełny tekst źródła
Streszczenie:
This Thesis aims to assess the reliability of turbulence models in predicting the flow fields around the horizontal axis wind turbine (HAWT) rotor blades and also to improve our understanding of the aerodynamics of the flow field around the blades. The simulations are validated against data from the NREL/NASA Phase VI wind turbine experiments. The simulations encompass the use of fourteen turbulence models including low-and high-Reynolds-number, linear and non-linear eddy-viscosity models and Reynolds stress models. The numerical procedure is based on the finite-volume discretization of the 3D
Style APA, Harvard, Vancouver, ISO itp.
42

Crow, Mallory Joyce. "Using Data Analytics to Determine Best Practices for Winter Maintenance Operations." University of Akron / OhioLINK, 2017. http://rave.ohiolink.edu/etdc/view?acc_num=akron1516351388406594.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
43

Sundberg, Johanna, Martina Lundberg, Julia Solhed, and Aikaterini Manousidou. "Two-dimensional Study of Blade Profiles for a Savonius Wind Turbine." Thesis, Uppsala universitet, Elektricitetslära, 2020. http://urn.kb.se/resolve?urn=urn:nbn:se:uu:diva-412795.

Pełny tekst źródła
Streszczenie:
A Savonius wind turbine is a self-starting vertical axis rotor. It can be designed to be compact in size and also produces less noise which makes it suitable to integrate into urban spaces such as rooftops and sign-poles. These characteristics make it interesting from a sustainability point of view, especially when aiming to increase the decentralization of electricity production. This thesis aimed to investigate the aerodynamic performance of different two-bladed Savonius profiles by varying the blade arc angle and the overlap ratio. For evaluation, the dimensionless power coefficient and tor
Style APA, Harvard, Vancouver, ISO itp.
44

O'Dowd, Devin Owen. "Aero-thermal performance of transonic high-pressure turbine blade tips." Thesis, University of Oxford, 2010. http://ora.ox.ac.uk/objects/uuid:e7b8e7d0-4973-4757-b4df-415723e7562f.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
45

Gorle, Jagan Mohan Rao. "Development of Circulation Controlled Blade Pitching Laws for Low-Velocity Darrieus Turbine." Thesis, Chasseneuil-du-Poitou, Ecole nationale supérieure de mécanique et d'aérotechnique, 2015. http://www.theses.fr/2015ESMA0021/document.

Pełny tekst źródła
Streszczenie:
L'étude développée dans cette thèse concerne le contrôle des performances et des lâchers tourbillonnaires au cours du cycle de rotation d'une hydrolienne à axe vertical de type Darrieus. L'élaboration d'une famille de lois de commande d'incidence de pales exploitant le principe de conservation de la circulation autour de profils en mouvement permet ici le contrôle du fonctionnement de l'hydrolienne ainsi que la maîtrise de son sillage tourbillonnaire afin de préserver l'environnement.L'écoulement 2D est simulé à l'aide du solveur incompressible de Star CCM+ afin de mettre en évidence l'effet d
Style APA, Harvard, Vancouver, ISO itp.
46

Tosun, Mehmet Mahir Özerdem Barış. "Investigation of aerodynamic effects on performance of wind turbine blades by using finite element method/." [s.l.]: [s.n.], 2005. http://library.iyte.edu.tr/tezlerengelli/master/enerjimuh/T000369.pdf.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
47

Bennett, Jeffrey. "The Effect of Mass and Web Spacing on the Loads and Structural Response of Increasing Wind Turbine Blade Size." Thesis, KTH, Kraft- och värmeteknologi, 2012. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-103434.

Pełny tekst źródła
Streszczenie:
The research presented considers the effect of varying shear web spacing and mass for two blades; a61.5m 5MW blade (based on the NREL5MW reference turbine) and a 100m 13.2MW blade (based onthe SNL100 blade). The variations are analyzed using HAWC2 aeroelastic simulations and Abaqus/CAE finite element simulations;and the effect of the variations is measured by comparing natural frequencies, loads, tip deflection,equivalent fatigue loads, material strength and buckling. Additionally, a tool was developed to facilitatethe modeling of blade variations. Varying the web spacing showed that the web p
Style APA, Harvard, Vancouver, ISO itp.
48

Toubia, Carim Miguel [UNESP]. "Estudo sobre as possibilidades de recuperação de resíduos provenientes da fabricação de pás eólicas." Universidade Estadual Paulista (UNESP), 2011. http://hdl.handle.net/11449/99731.

Pełny tekst źródła
Streszczenie:
Made available in DSpace on 2014-06-11T19:30:19Z (GMT). No. of bitstreams: 0 Previous issue date: 2011-08-05Bitstream added on 2014-06-13T21:00:51Z : No. of bitstreams: 1 toubia_cm_me_bauru.pdf: 3139754 bytes, checksum: d126c784c35fe683e0a8138af37f4346 (MD5)<br>O processo de fabricação das pás que equipam as modernas turbinas eólicas e o seu descarte no fim da vida útil podem ter impacto negativo sobre o meio ambiente. O presente trabalho busca soluções para reciclagem de resíduos de compósitos fibra de vidro/resina epóxi utilizados na fabricação das pás eólicas, tanto de porções sólidas ger
Style APA, Harvard, Vancouver, ISO itp.
49

Barrett, Ryan Timothy. "Investigation into Integrated Free-Form and Precomputational Approaches for Aerostructural Optimization of Wind Turbine Blades." BYU ScholarsArchive, 2018. https://scholarsarchive.byu.edu/etd/6673.

Pełny tekst źródła
Streszczenie:
A typical approach to optimize wind turbine blades separates the airfoil shape design from the blade planform design. This approach is sequential, where the airfoils along the blade span are pre-selected or optimized and then held constant during the blade planform optimization. In contrast, integrated blade design optimizes the airfoils and the blade planform concurrently and thereby has the potential to reduce cost of energy (COE) more than sequential design. Nevertheless, sequential design is commonly performed because of the ease of precomputation, or the ability to compute the airfoil ana
Style APA, Harvard, Vancouver, ISO itp.
50

Taylor, D. "The design and testing of a horizontal axis wind turbine with sailfoil blades." Thesis, Open University, 1985. http://oro.open.ac.uk/54193/.

Pełny tekst źródła
Streszczenie:
The work contained in this thesis covers the design, development and testing of a horizontal axis wind turbine (HAWT) with Sailfoil blades. Included is a brief history of wind turbine technology, its revival, a review of current wind energy developments and a literature survey of previous work on wind turbines with sail type blades. The Sailfoil blade consists of a framework of a leading edge D spar and a rigid trailing edge spar over which is stretched a fabric sock, forming a wing-like surface. The aerodynamic performance theories of HAWTs are described, as is the aerodynamic, structural and
Style APA, Harvard, Vancouver, ISO itp.
Możesz być także zainteresowany bibliografiami na temat „Winged blade” dla innych typów źródeł:
Artykuły w czasopismach Książki
Oferujemy zniżki na wszystkie plany premium dla autorów, których prace zostały uwzględnione w tematycznych zestawieniach literatury. Skontaktuj się z nami, aby uzyskać unikalny kod promocyjny!

Do bibliografii