Увійти

Готові списки джерел за темами / Heat resistant alloys / Статті в журналах

Щоб переглянути інші типи публікацій з цієї теми, перейдіть за посиланням: Heat resistant alloys.

Статті в журналах з теми "Heat resistant alloys"

Автор: Grafiati

Опубліковано: 4 червня 2021

Оновлено: 25 липня 2025

Оформте джерело за APA, MLA, Chicago, Harvard та іншими стилями

Оберіть тип джерела:

Ознайомтеся з топ-50 статей у журналах для дослідження на тему "Heat resistant alloys".

Біля кожної праці в переліку літератури доступна кнопка «Додати до бібліографії». Скористайтеся нею – і ми автоматично оформимо бібліографічне посилання на обрану працю в потрібному вам стилі цитування: APA, MLA, «Гарвард», «Чикаго», «Ванкувер» тощо.

Також ви можете завантажити повний текст наукової публікації у форматі «.pdf» та прочитати онлайн анотацію до роботи, якщо відповідні параметри наявні в метаданих.

Переглядайте статті в журналах для різних дисциплін та оформлюйте правильно вашу бібліографію.

1

Wang, Xiaomin, Yang Su, Lili Guo, Yan Liu, Honggang Li, and Hailin Ren. "Research Progress of Heat Resistant Magnesium Alloys." Journal of Physics: Conference Series 2160, no. 1 (2022): 012015. http://dx.doi.org/10.1088/1742-6596/2160/1/012015.

Повний текст джерела

Анотація:

Abstract Magnesium alloy has extremely excellent properties and is known as “21st Century Green Engineering Material”. This article mainly introduces the influence of the heat resistance and comprehensive performance of the three series of Mg-Al, Mg-Zn and Mg-RE heat-resistant magnesium alloys after adding rare earth elements, alkali metal elements and other elements. Three development directions of improving the heat resistance of magnesium alloys are prospected. These are: 1. Using cheap alloy elements (such as Ca, Si, etc.) to replace rare earth elements of the heat-resistant magnesium allo

Стилі APA, Harvard, Vancouver, ISO та ін.

2

Fridlyander, I. N., V. V. Antipov, T. P. Fedorenko, and E. G. Jakimova. "Properties of Rolled and Extruded Semiproducts Made of New Al-Cu-Mg-Ag Heat-Resistant B-1213 Alloy." Materials Science Forum 519-521 (July 2006): 483–88. http://dx.doi.org/10.4028/www.scientific.net/msf.519-521.483.

Повний текст джерела

Анотація:

Main properties and structure of 2 mm thick sheets and 20×100 mm extruded strips made under industrial conditions from Al-Cu-Mg heat-resistant B-1213 alloy with Ag, Cr, Mn and Zr additions were investigated. It was stated that wrought B-1213 alloy semiproducts are superior to analogous semis made of widely used commercial heat resistant AK4-1ch-type alloys (analogues - AU2GN, 2618 alloys) in strength properties and heat resistance characteristics (by 10-20 %) as well as in crack resistance and fatigue life (by 20-40 %). B-1213 alloy is intended for replacement of traditional heat-resistant all

Стилі APA, Harvard, Vancouver, ISO та ін.

3

Shalomeev, V. A., E. I. Tsyvirko, V. V. Klochyhin, and I. O. Chetvertak. "Heat-resistant magnesium-based alloys for aircraft casting." Metaloznavstvo ta obrobka metalìv 95, no. 3 (2020): 16–24. http://dx.doi.org/10.15407/mom2020.03.016.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

4

Han, Yu, Bao An Chen, Zhi Xiang Zhu, Dong Yu Liu, and Yan Qiu Xia. "Effects of Zr on Microstructure and Conductivity of Er Containing Heat-Resistant Aluminum Alloy Used for Wires." Materials Science Forum 852 (April 2016): 205–10. http://dx.doi.org/10.4028/www.scientific.net/msf.852.205.

Повний текст джерела

Анотація:

It has particular heat-resistant property and conductivity of high-conductivity heat-resistant Aluminium alloys, which would be wildly applied in transmission and transformation flied. Al-Er-Zr alloys containing different content of Zr were prepared. The effect of Zr on microstructure of heat-resistance Aluminum alloy were studied by using of STEM, and thermodynamic behavior of Zr in Aluminium alloy was analyzed based on the theory of alloy phase formation. The results showed that the effect of Zr content on the grain size of heat-resistant aluminum alloy was remarkable, and the conductivity o

Стилі APA, Harvard, Vancouver, ISO та ін.

5

Rowe, M. D., V. R. Ishwar, and D. L. Klarstrom. "Properties, Weldability, and Applications of Modern Wrought Heat-Resistant Alloys for Aerospace and Power Generation Industries." Journal of Engineering for Gas Turbines and Power 128, no. 2 (2004): 354–61. http://dx.doi.org/10.1115/1.2056527.

Повний текст джерела

Анотація:

Alloy selection and alloy design both require consideration of an array of material attributes, including in-service properties, weldability, and fabricability. Critical properties of modern heat-resistant alloys for gas turbine applications include high-temperature strength, thermal stability, oxidation resistance, and fatigue resistance. In this paper, the properties of 12 solid-solution-strengthened and six age-hardenable heat-resistant alloys are compared. Weldability is an important attribute and can be a major limiting factor in the use of certain alloys. Weldability test methods are dis

Стилі APA, Harvard, Vancouver, ISO та ін.

6

Vahrusheva, Vera, Diana Hlushkova, Volodymyr Volchuk, et al. "The effect of heat treatment on the corrosion resistance of power equipment parts." Bulletin of Kharkov National Automobile and Highway University, no. 97 (September 5, 2022): 24. http://dx.doi.org/10.30977/bul.2219-5548.2022.97.0.24.

Повний текст джерела

Анотація:

For the manufacture of parts and assemblies of the turbopump unit of details of power equipment, welded joints with corrosion resistant steels and heat-resistant alloys are used, requiring various modes heat treatment to achieve the required level of mechanical properties. In the manufacture of parts and assemblies of details of power equipment at the machine-building enterprises of Ukraine, it became necessary to replace semi-finished products. It is necessary to replace sheet products from high-alloy alloys ХН67МВТЮ and 06Х15Н6МВФБ with one alloy with a high complex of physical and mechanica

Стилі APA, Harvard, Vancouver, ISO та ін.

7

Al-Meshari, Abdulaziz, and John A. Little. "Oxidation of Commercial Heat-Resistant Alloys." Materials Performance 47, no. 6 (2008): 68–73. https://doi.org/10.5006/mp2008_47_6-68.

Повний текст джерела

Анотація:

Metal dusting is a chronic, costly problem for industrial equipment operating in highly carburizing environments. It has been strongly suggested that the development of a protective oxide scale on an alloy surface will considerably minimize the extent of metal dusting by slowing down the carbon diffusion into the alloy. This study was conducted to investigate the oxidation performance of several commercial alloys.

Стилі APA, Harvard, Vancouver, ISO та ін.

8

Mazalov, P. B., D. I. Suhov, E. A. Sulyanova, and I. S. Mazalov. "HEAT-RESISTANT COBALT-BASED ALLOYS." Aviation Materials and Technologies, no. 3 (2021): 3–10. http://dx.doi.org/10.18577/2713-0193-2021-0-3-3-10.

Повний текст джерела

Анотація:

Cobalt-based alloys are widely used for manufacturing of various components of gas turbine engines and gas turbines such as vanes and combustion chambers both in wrought state and as cast parts. They have been designed for improving the heat resistance due to solid solution and carbide-strengthening mechanisms. In order to obtain satisfactory oxidation resistance and hot corrosion resistance cobalt-based alloys are doped with sufficient amount of chromium (above 15 % wt.). Recently additive manufacturing has started to use cobalt-based alloys. The paper considers the features of the structure

Стилі APA, Harvard, Vancouver, ISO та ін.

9

Al-Meshari, Abdulaziz, and John Little. "Oxidation of Heat-resistant Alloys." Oxidation of Metals 69, no. 1-2 (2007): 109–18. http://dx.doi.org/10.1007/s11085-007-9086-6.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

10

Khalikov, Albert R., Evgeny A. Sharapov, Vener A. Valitov, Elvina V. Galieva, Elena A. Korznikova, and Sergey V. Dmitriev. "Simulation of Diffusion Bonding of Different Heat Resistant Nickel-Base Alloys." Computation 8, no. 4 (2020): 102. http://dx.doi.org/10.3390/computation8040102.

Повний текст джерела

Анотація:

Currently, an important fundamental problem of practical importance is the production of high-quality solid-phase compounds of various metals. This paper presents a theoretical model that allows one to study the diffusion process in nickel-base refractory alloys. As an example, a two-dimensional model of ternary alloy is considered to model diffusion bonding of the alloys with different compositions. The main idea is to divide the alloy components into three groups: (i) the base element Ni, (ii) the intermetallic forming elements Al and Ti and (iii) the alloying elements. This approach allows

Стилі APA, Harvard, Vancouver, ISO та ін.

11

Kalienko, M. S., A. A. Popov, A. V. Volkov, M. O. Leder, and A. V. Zhelnina. "Fatigue Resistance of the Sheets of Heat-Resistant Titanium Alloys." Fizika metallov i metallovedenie 125, no. 3 (2024): 366–74. http://dx.doi.org/10.31857/s0015323024030124.

Повний текст джерела

Анотація:

The results of a study of the resistance to fatigue fracture of sheets made of heat-resistant titanium alloys VT18U (Ti–6.5Al–4.3Zr–2.4Sn–0.8Nb–0.7Mo–0.1Si, wt.%), VT8 (Ti–6.4Al–3.4Mo–0.3Si, wt.%), and VT25U (Ti–6.51Al–3.76Zr–1.71Sn–3.94Mo–0.5W–0.13Si, wt.%) has been presented. Fatigue curves have been obtained in the initial state and in the oxidized one after isothermal annealing at a temperature of 560 °C for 1000 h in air. It has been established that after annealing, the fatigue resistance of all oxidized alloys in the low-cycle region decreases by an order of magnitude. The fatigue limit

Стилі APA, Harvard, Vancouver, ISO та ін.

12

KALININA, N. Ye, T. V. NOSOVA, N. I. TSOKUR, D. B. GLUSHKOVA, I. G. KIRICHENKO, and S. V. DEMCHENKO. "INCREASING CORROSION RESISTANCE OF WELDED JOINTS AS A RESULT OF HEAT TREATMENT." Physical Metallurgy and Heat Treatment of Metals 3, no. 3 (98) (2022): 28–32. http://dx.doi.org/10.30838/j.pmhtm.2413.270922.28.902.

Повний текст джерела

Анотація:

Welded joints with corrosion-resistant steels and heat-resistant alloys, which require different modes of heat treatment to achieve the level of mechanical properties specified in the design documentation, are used for the manufacture parts and assemblies of the rocket engine turbopump unit. Problem statement. In the production of rocket engine parts and components, due to difficulties in supplying materials from EU countries, Ukrainian machine-building enterprises have to substitute semi-finished products. It is necessary to replace sheet metal from high-alloy alloys with one alloy with a hig

Стилі APA, Harvard, Vancouver, ISO та ін.

13

Kalinina, Nataliya, Vasiliy Kalinin, and Ivannа Serzhenko. "Studying the effect of heat treatment modes on corrosion resistance of welded joints." Bulletin of Kharkov National Automobile and Highway University, no. 94 (December 16, 2021): 23. http://dx.doi.org/10.30977/bul.2219-5548.2021.94.0.23.

Повний текст джерела

Анотація:

Welded joints with corrosion-resistant steels and heat-resistant alloys, which require different modes of heat treatment to achieve the level of mechanical properties specified in the design documentation, are used for the manufacture of parts and components of the turbo-pumping unit (TPU) and liquid rocket engine. Heat-resistant alloys are a large group of alloys on iron, nickel and cobalt bases with the addition of chromium and other alloying elements (C, V, Mo, Nb, W, Ti, Al, B, etc.), whose main feature is to maintain high strength at high and cryogenic temperatures. Heat-resistant alloys

Стилі APA, Harvard, Vancouver, ISO та ін.

14

Byba, I. G., G. B. Levchenko, and O. O. Polehenko. "Heat-resistant intermetallic-based alloys and features of their alloying." Metaloznavstvo ta obrobka metalìv 30, no. 2 (2024): 58–67. http://dx.doi.org/10.15407/mom2024.02.058.

Повний текст джерела

Анотація:

The work considers the prerequisites for the development of creep-resistant and heat-resistant alloys, based on intermetallics, taking into account the optimal combination of their physical and mechanical properties, as well as structural characteristics. It is shown that there is a sufficient number of intermetallics, which have a density lower than iron-based alloys, which, in combination with high melting temperatures and heat resistance, makes them promising materials for aerospace application, in particular, for gas turbine engine parts manufacturing. The most suitable creep-resistant and

Стилі APA, Harvard, Vancouver, ISO та ін.

15

Osipov, P. A., R. A. Shayakhmetova, A. B. Sagyndykov, A. V. Panichkin, and A. A. Kali. "DENSITY OF HEAT-RESISTANT TITANIUM ALLOYS DOPED WITH LANTHANUM AND RHENIUM." Vestnik of the Kyrgyz-Russian Slavic University 23, no. 4 (2023): 79–86. http://dx.doi.org/10.36979/1694-500x-2023-23-4-79-86.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

16

Li, Delin, and Clayton Sloss. "Heat Treatment of Heat-Resistant Ferrous Cast Alloys." International Journal of Metalcasting 9, no. 2 (2015): 7–20. http://dx.doi.org/10.1007/bf03355611.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

17

Amenova, Aliya, Nikolay Belov, Dauletkhan Smagulov, and Ainagul Toleuova. "Scientifically Based Choice of Heat-Resistant Cast Aluminum Alloys of New Generation." Applied Mechanics and Materials 372 (August 2013): 49–53. http://dx.doi.org/10.4028/www.scientific.net/amm.372.49.

Повний текст джерела

Анотація:

The phase composition of the AlNiMnFeSiZr system is analyzed as applied to heat resistant nikalines (aluminum alloys of a new generation based on Ni containing eutectic), which are strengthened by the Al3Zr (L12) nanoparticles. It is shown that the presence of iron and silicon considerably complicates the phase analysis when compared with the AN4Mts2 base alloy. Silicon strongly widens the crystallization range, which increases the tendency of the alloy to form hot cracks during casting. It is shown that economically doped nikaline AN2ZhMts substantially exceeds the most heat resistant cast al

Стилі APA, Harvard, Vancouver, ISO та ін.

18

Larionova, Tatyana, Sergei A. Lyubomudrov, and Evgeniy Larionov. "Machinability of Heat-Resistant Titanium Alloys during Turning." Materials Science Forum 1022 (February 2021): 62–70. http://dx.doi.org/10.4028/www.scientific.net/msf.1022.62.

Повний текст джерела

Анотація:

The article discusses the properties and features of heat-resistant titanium alloys. The microstructure of a new titanium alloy VT41, its mechanical and service properties after various processing modes are presented. The main problems in the machining of difficult-to-machine titanium alloys are considered. The developed mathematical model of the formation of errors in turning titanium alloys, taking into account thermal deformations and dimensional wear of the cutting tool, elastic deformations of the technological system, is described. The paper presents the results of experimental research

Стилі APA, Harvard, Vancouver, ISO та ін.

19

Glotka, O., and V. Olshanetskii. "Properties of nickel-based superalloys of equiaxial crystallization." Innovative Materials and Technologies in Metallurgy and Mechanical Engineering, no. 1 (September 14, 2021): 19–23. http://dx.doi.org/10.15588/1607-6885-2021-2-3.

Повний текст джерела

Анотація:

Purpose. The aim of the work is to obtain predictive regression models, with the help of which, it is possible to adequately calculate the mechanical properties of nickel-based superalloys of equiaxial crystallization, without carrying out preliminary experiments. Research methods. To find regularities and calculate the latest CALPHAD method was chosen, and modeling of thermodynamic processes of phase crystallization was performed. Results. As a result of experimental data processing, the ratio of alloying elements Kg¢ was proposed for the first time, which can be used to assess th

Стилі APA, Harvard, Vancouver, ISO та ін.

20

Groza, Joanna. "Heat-resistant dispersion-strengthened copper alloys." Journal of Materials Engineering and Performance 1, no. 1 (1992): 113–21. http://dx.doi.org/10.1007/bf02650042.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

21

Skachkov, O. A. "Heat-resistant structural-grade powder alloys." Metallurgist 48, no. 9-10 (2004): 484–86. http://dx.doi.org/10.1007/s11015-005-0010-5.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

22

Ospennikova, O. G., B. S. Lomberg, N. V. Moiseev, and D. V. Kapitanenko. "Isothermal Deformation of Heat-Resistant Alloys." Metallurgist 57, no. 9-10 (2014): 949–53. http://dx.doi.org/10.1007/s11015-014-9827-0.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

23

Saikawa, Seiji, Manabu Mizutani, and Nozomu Kawabe. "Effect of Sn Content on Heat Resistance of Mg-3%Al-1%Si Alloy for Casting." Materials Science Forum 941 (December 2018): 1071–76. http://dx.doi.org/10.4028/www.scientific.net/msf.941.1071.

Повний текст джерела

Анотація:

Magnesium alloys have the characteristic with high specific strength and lightweight property, it is widely used for auto mobile industry. Heat-resistant magnesium alloy is focused as a suitable material for weight reduction of the engine and power train parts in automotive field. In this study, microstructure and heat-resistant property in Mg-3mass%Al-1mass%Si (Mg-3%Al-1%Si) alloy with containing large amount of Sn (tin) were investigated. The alloys produced by permanent mold casting were investigated by optical microscope (OM), scanning electron microscopy (SEM) and measuring of bolt load r

Стилі APA, Harvard, Vancouver, ISO та ін.

24

Getsov, L. B., A. I. Rybnikov, I. S. Malashenko, K. Yu Yakovchuk, Yu P. Belolipetskii, and V. N. Torgov. "The fatigue resistance of heat resistant alloys with coatings." Strength of Materials 22, no. 5 (1990): 685–91. http://dx.doi.org/10.1007/bf00806269.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

25

Lo´pez de Lacalle, L. N., J. A. Sa´nchez, A. Lamikiz, and A. Celaya. "Plasma Assisted Milling of Heat-Resistant Superalloys." Journal of Manufacturing Science and Engineering 126, no. 2 (2004): 274–85. http://dx.doi.org/10.1115/1.1644548.

Повний текст джерела

Анотація:

The term Thermal Enhanced Machining refers to a conventional cutting process in which an external energy source is used to enhance the chip-generation mechanism. The work presented here analyzes the basic aspects and the experimental results obtained when applying an assisting plasma jet to the milling process. This process, known as PAM (Plasma Assisted Milling) has been applied to the machining of three very low machinability materials: a Ni-base alloy (Inconel 718), a Co-base alloy (Haynes 25), (both belonging to the group of the heat-resistant alloys) and the Ti-base alloy Ti6Al4V. The stu

Стилі APA, Harvard, Vancouver, ISO та ін.

26

程, 鹏. "Research Progress on Heat-Resistant Phases in Cast Heat-Resistant Aluminum Alloys." Material Sciences 14, no. 04 (2024): 433–42. http://dx.doi.org/10.12677/ms.2024.144050.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

27

Kozlov, Arkadiy, and M. Deryabin. "Pulsed Processes when Cutting Heat-Resistant Alloys." Key Engineering Materials 496 (December 2011): 144–49. http://dx.doi.org/10.4028/www.scientific.net/kem.496.144.

Повний текст джерела

Анотація:

In this paper, the pulsed processes of machining by cutting heat-resistant alloys are consid-ered. It is proved that such processes can exclude unwanted loss of the steadiness of elastoplastic deformations in the chip formation zone. As a result the accuracy of machining, the quality of ma-chined surface and the resistance to wear of the cutting tool increase. Finally, some methods of in-tensification of pulsed processes when cutting difficult to machine materials have been suggested.

Стилі APA, Harvard, Vancouver, ISO та ін.

28

Evdokimov, V. B., A. A. Artamonov, E. V. Plotnikov, and N. A. Konstantinova. "RESOURCE-EFFICIENT METHODS FOR PREDICTING AND SELECTING HEAT-RESISTANT ALLOYS." Resource-Efficient Technologies, no. 2 (July 11, 2019): 17–28. http://dx.doi.org/10.18799/24056537/2019/2/233.

Повний текст джерела

Анотація:

The power plant resource efficiency is largely dependent on heat-resistant alloys and is limited by the standard turbine operating temperature, which is slightly greater than 1000°C. These temperature limits are dependent on the characteristics of the heat-resistant alloys used in power plants. The current research aimed to discover new heat-resistant alloys using computer-based models to simulate the various properties of such materials. The first-principle methods were initially used in this study. These methods can determine the most important properties of alloys with a high degree of accu

Стилі APA, Harvard, Vancouver, ISO та ін.

29

Evdokimov, V. B., A. A. Artamonov, E. V. Plotnikov, and N. A. Konstantinova. "RESOURCE-EFFICIENT METHODS FOR PREDICTING AND SELECTING HEAT-RESISTANT ALLOYS." Resource-Efficient Technologies, no. 2 (July 11, 2019): 17–28. http://dx.doi.org/10.18799/24056529/2019/2/233.

Повний текст джерела

Анотація:

The power plant resource efficiency is largely dependent on heat-resistant alloys and is limited by the standard turbine operating temperature, which is slightly greater than 1000°C. These temperature limits are dependent on the characteristics of the heat-resistant alloys used in power plants. The current research aimed to discover new heat-resistant alloys using computer-based models to simulate the various properties of such materials. The first-principle methods were initially used in this study. These methods can determine the most important properties of alloys with a high degree of accu

Стилі APA, Harvard, Vancouver, ISO та ін.

30

Zhang, Haiyang, Zeyu Li, Daihong Xiao, Mingdong Wu, Yang Huang, and Wensheng Liu. "Enhanced Strength of Al-10Ce-3Mg-5Zn Heat-Resistant Alloy by Combining Extrusion and Heat Treatment." Materials 18, no. 8 (2025): 1706. https://doi.org/10.3390/ma18081706.

Повний текст джерела

Анотація:

The existing Al-Ce heat-resistant alloys are not extensively utilized in high-temperature applications due to their poor room-temperature mechanical properties. In this study, the Al-10Ce-3Mg-5Zn alloy was enhanced using hot extrusion and heat treatment. The as-extruded alloy exhibited bimodal intermetallic compounds and grain structures. Additionally, high-density microcracks and twins were observed in the micron-sized intermetallic compounds. Compared with the as-cast state, the as-extruded alloy demonstrated a higher ultimate tensile strength (UTS) of 317 MPa and better elongation of 11.0%.

Стилі APA, Harvard, Vancouver, ISO та ін.

31

Povarova, K. B., A. E. Morozov, and A. A. Drozdov. "Heat-resistant RuAl-based alloys. Part I. Casting alloys." Perspektivnye Materialy, no. 11 (2019): 5–18. http://dx.doi.org/10.30791/1028-978x-2019-11-5-18.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

32

Povarova, K. B., A. E. Morozov, and A. A. Drozdov. "Heat-Resistant RuAl-Based Alloys: Part I. Cast Alloys." Inorganic Materials: Applied Research 11, no. 2 (2020): 277–86. http://dx.doi.org/10.1134/s2075113320020318.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

33

Batako, Andre, Anatoliy Matveevich Adaskin, Victor Nikolaevich Butrim, Alexey Anatolevich Vereschaka, and Anatoliy Stepanovich Vereschaka. "Influence of Carbide Substrate Properties on Wear Resistance of Tool with Multilayer Coating in Machining of Chromium-Based Heat-Resistant Alloy." Materials Science Forum 876 (October 2016): 59–68. http://dx.doi.org/10.4028/www.scientific.net/msf.876.59.

Повний текст джерела

Анотація:

Thispaper presents the results of the studies of the combined influence of properties of carbide substrate and composite coatings on tool wear resistance in machining of chromium-based heat-resistant alloys. It was established that the efficiency of carbide tools with coatings is determined by a combination of the properties of the carbide substrate and the coating itself. For carbides with relatively low strength and crack resistance, the efficiency of coatings appeared to be unsatisfactory because of brittle fracture of the substrate and thus intensive failure of coating. High heat resistanc

Стилі APA, Harvard, Vancouver, ISO та ін.

34

Glotka, O. A., and V. Yu Olshanetskii. "Predicting the properties of nickel-based superalloys directional crystallization." Metaloznavstvo ta obrobka metalìv 99, no. 3 (2021): 15–22. http://dx.doi.org/10.15407/mom2021.03.015.

Повний текст джерела

Анотація:

The aim of this work is to obtain predictive regression models, with which it is possible to adequately calculate the mechanical properties of heat-resistant nickel alloys, without prior experiments. Industrial alloys of directional crystallization of domestic and foreign production were selected for research. The values were processed by the method of least squares to obtain correlations with the receipt of mathematical equations of regression models that optimally describe these dependencies. As a result of processing of experimental data, the ratio of alloying elements which can be used for

Стилі APA, Harvard, Vancouver, ISO та ін.

35

Balitskii, Alexander I., Yuliia H. Kvasnytska, Lyubomir M. Ivaskevych, et al. "Hydrogen and Corrosion Resistance of Nickel Superalloys for Gas Turbines, Engines Cooled Blades." Energies 16, no. 3 (2023): 1154. http://dx.doi.org/10.3390/en16031154.

Повний текст джерела

Анотація:

The paper presents the results of the analysis of the resistance to hydrogen and high-temperature salt corrosion of the developed alloy of the CM88Y type for the turbine blades of gas turbine engines for marine and power purposes in comparison with the industrial heat-resistant corrosion-resistant alloy CM88Y and the alloy for the protective coating of the SDP3-A blades. SDP3-A alloy was chosen as a reference sample, which has high hydrogen and corrosion resistance. The new heat-resistant alloy additionally contains such refractory metals as rhenium and tantalum, which are added to the composi

Стилі APA, Harvard, Vancouver, ISO та ін.

36

Калініна, Наталія Євграфівна, Олександр Васильович Калінін, Тетяна Валеріївна Носова, Стелла Ігорівна Мамчур та Наталія Іванівна Цокур. "Розробка технології дисперсного модифікування жароміцних нікелевих сплавів для лопаток газотурбінних двигунів". Aerospace technic and technology, № 3 (27 травня 2021): 49–53. http://dx.doi.org/10.32620/aktt.2021.3.06.

Повний текст джерела

Анотація:

The paper proposes means of improving the properties of nickel alloys for aircraft gas turbine engines by improving the existing alloys. The efficiency of an aircraft engine depends on the quality of the turbine rotor blades, which are made of heat-resistant alloys. According to the studies, the obtained results of pilot tests of a complex of mechanical properties, high-temperature corrosion of a multicomponent high-temperature nickel alloy ХН59МВТКЮЛ (Ni-Cr-W-Co-Al-Ti-Mo systems). The paper proposes the use of modifiers. An effective means of dispersing the structural components of alloys at

Стилі APA, Harvard, Vancouver, ISO та ін.

37

Huang, Zhuofang, Anmin Li, Wendi Zhou, Jinjin Li, and Jinkai Zhang. "Effects of Red Mud on Microstructures and Heat Resistance of ZL109 Aluminum Alloy." Materials 18, no. 3 (2025): 664. https://doi.org/10.3390/ma18030664.

Повний текст джерела

Анотація:

The effects of red mud on the microstructures and high-temperature tensile properties of the ZL109 aluminum alloy have been investigated. Red mud/ZL109-based composite materials with added red mud (a major byproduct of the aluminum industry), which has been coated with nickel by chemical deposition, have been prepared through gravity casting. The results show that the addition of red mud promotes the alloy’s microstructure and helps to uniformly distribute the eutectic silicon. It also increases the content of heat-resistant phases, such as the Q-Al5Cu2Mg8Si6 and γ-Al7Cu4Ni phases. These chang

Стилі APA, Harvard, Vancouver, ISO та ін.

38

Tsukeda, Tadayoshi, Ken Saito, Mayumi Suzuki, Junichi Koike, and Kouichi Maruyama. "Newly Developed Heat Resistant Magnesium Alloy by Thixomolding^®." Materials Science Forum 488-489 (July 2005): 287–90. http://dx.doi.org/10.4028/www.scientific.net/msf.488-489.287.

Повний текст джерела

Анотація:

We compared the newly developed heat resistant magnesium alloy with conventional ones by Thixomolding® and aluminum alloy by die casting. Tensile properties at elevated temperatures of AXEJ6310 were equal to those of ADC12. In particular, elongation tendency of AXEJ6310 at higher temperature was better than those of the other alloys. Creep resistance of AXEJ6310 was larger than that of AE42 by almost 3 orders and smaller than that of ADC12 by almost 2 orders of magnitude. Fatigue limits at room temperature and 423K of AXEJ6310 was superior among conventional magnesium alloys.

Стилі APA, Harvard, Vancouver, ISO та ін.

39

Tang, Jinjun, Cui Liang, and Jiqiang Li. "Effect of alloying elements on coexisting phases and microstructure of M174 heat-resistant aluminum alloy." Journal of Physics: Conference Series 2879, no. 1 (2024): 012002. http://dx.doi.org/10.1088/1742-6596/2879/1/012002.

Повний текст джерела

Анотація:

Abstract This article mainly focuses on high-power density diesel engine piston alloys, with the main component system being M174 heat-resistant aluminum alloy. On this basis, the main heat-resistant alloying elements Cu, Ni, and Fe were optimized and designed. This article is based on Thermo-Calc thermodynamic software, and comprehensively calculates and analyzes the multi-component alloy equilibrium phase diagram and Scheil non-equilibrium solidification of Al-(4-6)Cu-(1.5-3)Ni-(0.7-1.1Fe)-12.5Si-0.85Mg (mt.%) heat-resistant aluminum alloy system. Through the orthogonal experimental method o

Стилі APA, Harvard, Vancouver, ISO та ін.

40

Getsov, L. B., A. I. Rybnikov, and A. S. Semenov. "Thermal fatigue strength of heat-resistant alloys." Thermal Engineering 56, no. 5 (2009): 412–20. http://dx.doi.org/10.1134/s0040601509050103.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

41

Schroth, James G., and Vjekoslav Franetovic. "Mechanical Alloying for Heat-Resistant Copper Alloys." JOM 41, no. 1 (1989): 37–39. http://dx.doi.org/10.1007/bf03220801.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

42

Calmunger, Mattias, Hugo Wärner, Guocai Chai, and Mikael Segersäll. "Thermomechanical Fatigue of Heat Resistant Austenitic Alloys." Procedia Structural Integrity 43 (2023): 130–35. http://dx.doi.org/10.1016/j.prostr.2022.12.247.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

43

Kalienko, M. S., A. A. Popov, A. V. Volkov, M. O. Leder, and A. V. Zhelnina. "Fatigue Resistance of the Sheets of Heat-Resistant Titanium Alloys." Physics of Metals and Metallography 125, no. 3 (2024): 332–39. http://dx.doi.org/10.1134/s0031918x23603141.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

44

Gubanov, O. M., V. N. Gadalov, Yu V. Skripkina та I. A. Makarova. "Increasing the heat resistance of cast nickel-based complex alloyed alloys due to the influence of the redistribution of alloying elements between the γ-solid solution and the strengthening intermetallic γ'-phase". Glavnyj mekhanik (Chief Mechanic), № 12 (1 грудня 2020): 67–79. http://dx.doi.org/10.33920/pro-2-2012-07.

Повний текст джерела

Анотація:

The analysis of alloying of the chemical and phase composition of domestic and foreign cast heat-resistant alloys with a nickel matrix is carried out; the tendency to increase the level of heat-resistant properties of cast nickel alloys due to more complex alloying is traced. Recently, expensive rhenium, ruthenium, hafnium, and dysprosium have increasingly been used as alloying elements. The positive effect of these elements on the thermal stability of the γ-matrix and the strengthening γ'-phase is established. The above elements inhibit diffusion processes, thereby increasing the creep resist

Стилі APA, Harvard, Vancouver, ISO та ін.

45

Ternovyi, Yu F., S. A. Vodennikov, and O. S. Vodennikova. "Inert gas absorption and pore formation in nickel-based hot-melt alloys." Metaloznavstvo ta obrobka metalìv 97, no. 1 (2021): 20–27. http://dx.doi.org/10.15407/mom2021.01.020.

Повний текст джерела

Анотація:

An integrated approach to the generalization and analysis of scientific and technical literature in the direction of improving the technological processes of spraying metal melts used a comprehensive approach The processing and analysis of experimental data for the determination of argon at different stages of heat-resistant alloy production were performed. Micro structural analysis of nickel-based heat-resistant alloys obtained by gas and centrifugal spraying was performed. A significant increase in the mass fraction of argon in the melt is shown when held in a furnace before gas or centrifug

Стилі APA, Harvard, Vancouver, ISO та ін.

46

Kalashnikov, V. S., L. P. Reshetilo, O. V. Chuchman та S. A. Naprienko. "STRENGTH AND RELIABILITY OF RODS AND ROTOR BLADE STAMPS MADE OF HEAT-RESISTANT INDUSTRIAL TITANIUM ALLOYS AND MODERN PSEUDO-α-TITANIUM ALLOY". Proceedings of VIAM, № 2 (2022): 13–31. http://dx.doi.org/10.18577/2307-6046-2022-0-2-13-31.

Повний текст джерела

Анотація:

Presents the microstructure and mechanical properties of bars and blade forgings made of new heat resistant titanium alloy. A typical microstructures of studied industrial alloys were demonstrated. The main clue of the article is noted to fatigue stability of bars and forgings material. The analysis of strength and impact toughness of bars and blade forgings made of industrial titanium alloys VT3-1, VT8, VT8M-1, VT9, VT20 were carried out in comparison with new heat-resistant titanium near- alloy.

Стилі APA, Harvard, Vancouver, ISO та ін.

47

Kvasnytska, Y. H., I. A. Shalevska, A. I. Balitskii, L. M. Ivaskevich, І. І. Maksiuta, and K. H. Kvasnytska. "Influence of Refractory Elements on Phase–Structural Stability of Heat-Resistant Corrosion-Resistant Alloys for Gas Turbine Blades." METALLOFIZIKA I NOVEISHIE TEKHNOLOGII 45, no. 8 (2024): 975–92. http://dx.doi.org/10.15407/mfint.45.08.0975.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

48

Veselkov, Sergey, Olga Samoilova, Nataliya Shaburova, and Evgeny Trofimov. "High-Temperature Oxidation of High-Entropic Alloys: A Review." Materials 14, no. 10 (2021): 2595. http://dx.doi.org/10.3390/ma14102595.

Повний текст джерела

Анотація:

Over the past few years, interest in high-entropic alloys (HEAs) has been growing. A large body of research has been undertaken to study aspects such as the microstructure features of HEAs of various compositions, the effect of the content of certain elements on the mechanical properties of HEAs, and, of course, special properties such as heat resistance, corrosion resistance, resistance to irradiation with high-energy particles, magnetic properties, etc. However, few works have presented results accumulated over several years, which can complicate the choice of directions for further research

Стилі APA, Harvard, Vancouver, ISO та ін.

49

Povarova, K. B., A. E. Morozov, A. A. Drozdov, A. V. Antonova, and M. A. Bulakhtina. "Heat-Resistant RuAl-Based Alloys: III. Powder Alloys—Mechanical Alloying." Inorganic Materials: Applied Research 13, no. 2 (2022): 294–305. http://dx.doi.org/10.1134/s2075113322020344.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

50

Povarova, K. B., A. E. Morozov, A. A. Drozdov, A. V. Antonova, and M. A. Bulakhtina. "Heat-resistant RuAl-based alloys. III. Powder alloys — mechanical alloying." Perspektivnye Materialy 11 (2021): 5–19. http://dx.doi.org/10.30791/1028-978x-2021-11-5-19.

Повний текст джерела

Анотація:

Refractory (Tmelt = 2100 °C), heat-resistant ruthenium monoaluminide RuAl, lighter (ρ = 7.97 g/cm3) than Ni superalloys, is considered as a promising candidate material for operation at high temperatures and relatively low loads in high-speed gas oxidizing flows at temperatures higher not only operating temperatures, but also the melting temperatures of both nickel superalloys and nickel and titanium aluminides. RuAl is also an ideal candidate for potential protective coatings. In the first part of the article, RuAl-based cast alloys were considered. In the second part of the article, the poss

Стилі APA, Harvard, Vancouver, ISO та ін.

Ми пропонуємо знижки на всі преміум-плани для авторів, чиї праці увійшли до тематичних добірок літератури. Зв'яжіться з нами, щоб отримати унікальний промокод!