Relevant bibliographies by topics / Aluminium Alloys - Mechanical Properties

Contents

  1. Dissertations / Theses

Academic literature on the topic 'Aluminium Alloys - Mechanical Properties'

Author: Grafiati
Published: 4 June 2021
Last updated: 6 September 2023

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles

Select a source type:

Consult the lists of relevant articles, books, theses, conference reports, and other scholarly sources on the topic 'Aluminium Alloys - Mechanical Properties.'

Next to every source in the list of references, there is an 'Add to bibliography' button. Press on it, and we will generate automatically the bibliographic reference to the chosen work in the citation style you need: APA, MLA, Harvard, Chicago, Vancouver, etc.

You can also download the full text of the academic publication as pdf and read online its abstract whenever available in the metadata.

Dissertations / Theses on the topic "Aluminium Alloys - Mechanical Properties"

1

Seifeddine, Salem. "Characteristics of cast aluminium-silicon alloys : microstructures and mechanical properties /." Linköping : Univ, 2006. http://www.bibl.liu.se/liupubl/disp/disp2006/tek1058s.pdf.

Full text
APA, Harvard, Vancouver, ISO, and other styles
2

El-Sayed, Mahmoud Ahmed Mahmoud. "Double oxide film defects and mechanical properties in aluminium alloys." Thesis, University of Birmingham, 2012. http://etheses.bham.ac.uk//id/eprint/3924/.

Full text
Abstract:
Double oxide films (bifilms) are significant defects in light alloy castings which were reported to have detrimental effects on the reliability of the castings. The research reported here was aimed at studying how these defects develop with time. The results suggested that both O and N inside the bifilm would be consumed by reaction with the surrounding melt, and that H might be diffused into the defect. Based on the estimated reactions rates the time required for the consumption of the atmosphere inside a bifilm entrained in pure Al, Al-7wt.%Si-0.3wt.%Mg and Al-5wt.%Mg alloy melts, was determ
APA, Harvard, Vancouver, ISO, and other styles
3

Kerry, S. "Microstructure and mechanical properties of high strength cast aluminium alloys." Thesis, University of Bath, 1987. https://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.376328.

Full text
APA, Harvard, Vancouver, ISO, and other styles
4

O'Rourke, Jane. "Microstructure and mechanical properties of fibre-reinforced heat-treatable aluminium alloys." Thesis, University of Bath, 1995. https://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.261348.

Full text
APA, Harvard, Vancouver, ISO, and other styles
5

Payandeh, Mostafa. "Rheocasting of Aluminium Alloys : Slurry Formation, Microstructure, and Properties." Licentiate thesis, Tekniska Högskolan, Högskolan i Jönköping, JTH. Forskningsmiljö Material och tillverkning – Gjutning, 2015. http://urn.kb.se/resolve?urn=urn:nbn:se:hj:diva-26297.

Full text
Abstract:
Innovative materials with novel properties are in great demand for use in the criticalcomponents of emerging technologies, which promise to be more cost-effective and energyefficient.A controversial issue with regard to manufacturing complex industrial products isto develop advanced materials with optimised manufacturability in addition to the requiredmechanical and physical properties. The objective of this research study was to develop andoffer new solutions in material-processing-related issues in the field of mechanical andelectrical engineering. This was achieved by investigating the new
APA, Harvard, Vancouver, ISO, and other styles
6

Sawalha, Kameel. "The fatigue properties of pressure diecast zinc-aluminium based alloys." Thesis, Aston University, 1991. http://publications.aston.ac.uk/11933/.

Full text
Abstract:
The fatigue behaviour of the cold chamber pressure-die-cast alloys: Mazak3, ZA8, ZA27, M3K, ZA8K, ZA27K, K1, K2 and K3 was investigated at temperature of 20oC. The alloys M3K, ZA8K and ZA27K were also examined at temperatures of 50 and 100oC. The ratio between fatigue strength and tensile strength was established at 20oC at 107 cycles. The fatigue life prediction of the alloys M3K, ZA8K and ZA27K was formulated at 20, 50 and 100oC. The prediction formulae were found to be reasonably accurate. All of the experimental alloys were heterogeneous and contained large but varying amounts of pores. Th
APA, Harvard, Vancouver, ISO, and other styles
7

Mir, Arshad A. "The creep properties of a series of zinc-rich zinc-aluminium alloys." Thesis, Aston University, 1998. http://publications.aston.ac.uk/13277/.

Full text
Abstract:
The compressive creep behaviour of six sand cast zinc-rich alloys: No3 and No5, corresponding to BS 1004A and BS 1004B, respectively, alloy No2, ILZRO,.16 and two newer alloys ACuZinc5 and ACuZinc10 was investigated. The total creep contraction of the alloys was found to be well correlated using an empirical equation. On the basis of this equation, a parametrical relationship was derived which allowed the total creep contraction to be related to the applied stress, the temperature and the time of test, so that a quantitative assessment of compressive creep of the alloys could be made under dif
APA, Harvard, Vancouver, ISO, and other styles
8

Stein, Julien. "AA5083 aluminium alloys reinforced with multi-walled carbon nanotubes : microstructure and mechanical properties." Thesis, Montpellier 2, 2012. http://www.theses.fr/2012MON20002.

Full text
Abstract:
Cette étude a pour but de développer de nouveaux matériaux composites à matrice métallique renforcés par des nanotubes de carbone (CNT) et présentant des propriétés mécaniques améliorées. La majeure partie de ce travail a été réalisée en utilisant des CNT multi-feuillets synthétisés par déposition chimique en phase vapeur en tant que renforts et un alliage d'aluminium AA5083 comme matrice. Des composites CNT/AA5083 denses et homogènes ont été élaborés par le procédé de métallurgie des poudres suivi par une étape de mise en forme, l'extrusion. L'homogénéité de la dispersion des CNT à l'échelle
APA, Harvard, Vancouver, ISO, and other styles
9

Zander, Johan. "Modelling mechanical properties by analysing datasets of commercial alloys." Licentiate thesis, Stockholm : Industriell teknik och management, Kungliga Tekniska högskolan, 2007. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-4527.

Full text
APA, Harvard, Vancouver, ISO, and other styles
10

Hashemi-Ahmady, M. "Solidification, structure and mechanical properties of A357 aluminium alloy." Thesis, University of Southampton, 1987. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.381127.

Full text
APA, Harvard, Vancouver, ISO, and other styles
More sources
You might also be interested in the extended bibliographies on the topic 'Aluminium Alloys - Mechanical Properties' for particular source types:
Dissertations / Theses
We offer discounts on all premium plans for authors whose works are included in thematic literature selections. Contact us to get a unique promo code!

To the bibliography