Dissertations / Theses on the topic 'Bit Patterned Media (BPM)'

Highly ordered magnetic materials with high perpendicular magnetic anisotropy (PMA), such as the L10 ordered FePt, and new recording technologies, such as bit patterned media (BPM), have been proposed as solutions to the media trilemma problem and provide promising strategies towards future high-density magnetic data storage media. L10 ordered FePt thin films can provide the necessary high PMA. However, the ordering of this material perpendicular to the plane of the films remains challenging since high-temperature and time-consuming processes are required. In this work, a remote plasma sputtering system has been used for the investigation of FePt thin films in order to understand if the greater control of process parameters offered by this system can lead to enhanced ordering in L10 FePt thin films at low temperatures compared with conventional dc magnetron approaches. More specifically, the effect of the different substrate temperatures and the target bias voltages on the ordering, the microstructure and the magnetic properties of FePt thin films was investigated. Highly ordered FePt thin films were successfully fabricated after post-annealing processes and were patterned into arrays of FePt islands. This patterning process was carried out with e-beam lithography and ion milling. Initial MFM measurements of these islands showed their single-domain structure for all the island sizes, which indicated the high PMA of the FePt. Magnetometry measurements were also carried out with a novel polar magneto-optical Kerr effect (MOKE) system which was designed and built during this project. This system has unique capabilities which are: a) the application of uniform magnetic field up to 2 Tesla, b) the rotation of the field to an arbitrary angle and c) the use of lasers of four different wavelengths. The combination of these abilities enabled measurements on ordered FePt thin films and patterned media which can pave the way for further highly sensitive measurements on magnetic thin films and nanostructures.

The work in this PhD thesis covers two strands of x-ray experiments: firstly, the characterisation of large arrays of dense structures by means of x-ray scattering, and, secondly, the investigation of hybrid anisotropy square structures with x-ray microscopy. The ability to accurately characterise large arrays of nanoscale magnetic structures is a key requirement for both scientific understanding and technological advance such as bit patterned recording media (BPM). In this work small angle x-ray scattering (SAXS) was investigated as a characterisation technique for large arrays of patterned structures. Dense arrays of magnetic nanostructures were prepared on x-ray transparent membranes and measured. The SAXS data was then modelled to obtain structure parameters such as the mean structure diameter, the diameter distribution and the mean position variance with statistical significance. Arrays (500 x 500 μm2) of nominally uniform nanostructures with centre-to-centre distances between 250 nm-50 nm were structurally characterised and compared to structure diameters obtained by optical scanning electron microscopy measurements. The mean structure diameter was found to be between 39 nm-15nm and agree within the errors with the diameter obtained from SEM measurements. This work provides accurate data on the distribution (variance) of nanostructure sizes which is key for modelling these arrays for applicationin BPM. In the second part of the work, the static and dynamic properties of patterned hybrid anisotropy square structures ([Co/Pd]-Py) were investigated by using time-resolved scanning transmission X-ray microscopy (STXM). In these patterned structures the magnetisation in the layers change both in magnitude and direction and gives rise to interesting new domain configurations. The reciprocal interaction between magnetic vortices in the Py layer and locally circular stripe domains in the Co/Pd was investigated and a mutual domain imprint between the layer was observed. In dynamic excitation experiments the precession of the vortex core is studied and showed good agreement with micromagnetic simulations made by Hrkac and Bryan. As demonstrated patterned hybrid anisotropy square structures have promising magnetic properties with potential applications in data storage (vortex switching) or spintronics (vortex oscillators).

Thesis (M. Eng.)--Massachusetts Institute of Technology, Dept. of Materials Science and Engineering, 2009.
This electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.
Cataloged from student submitted PDF version of thesis.
Includes bibliographical references (p. 75-79).
Realm of data storage density has expanded from gigabyte- to terabyte-domain. In such a high areal density, bit-patterned media is a promising candidate to overcome the superparamagnetic limit faced by the conventional continuous media. However, the patterned media concept has not been realized in mass production due to several reasons. Beside the stringent requirement of high-resolution lithography, high production cost is inevitably the major challenging problem. If a low-cost mass fabrication scheme is available, bit-patterned media will be an innovative way in hard disk technology to achieve a storage density beyond 1 Tb/in². The objective of this thesis is to review the patterned media technology and discuss its challenges and commercialization viability. A possible mass-production scheme is discussed. Electron beam lithography and self assembly process of block copolymer are used to fabricate the master template. To ensure high throughput, template replication as well as disk fabrication are carried out by UV-nanoimprint lithography (UV-NIL). Considering the large opportunity of patterned media to enter the market, a business plan was constructed. Enormous profit was proved to be possible when the barrier of technology, intellectual property, and funding can be surpassed. Therefore, patterned media shows to be superior in terms of performance and cost compared to the conventional media.
by Ria Esterina.
M.Eng.

The fabrication of Bit Patterned Media has become highly developed, with samples fabricated of over 1.5 Tb/in2. However, writing BPM presents significant challenges and for a system to be developed studies must be made into writing. This work has investigated a number of effects on the writing of Bit Pattterned Media (BPM). Magnetostatic interactions between islands have been used to investigate the effect of patterns of magnetisation on the write-window of a BPM system. A method of acquiring a distribution of patterns was determined and used to vary the probability of a target island switching. This showed that magnetostatic interactions between islands could be modelled as a variation in the anisotropy field. The relationship between island parameter distributions, the write-window and error rates was also explored. The effect of non-Gaussian distributions on the error in a BPM system was studied. It was concluded that tails of island parameter distributions have a significant effect on errors occurring in the write process of a BPM system. Therefore an accurate distribution of island parameters must be known and the necessary accuracy of such a distribution was established. Furthermore a model of BPM writing where the shape of the head field is approximated from the value at the maximum head field gradient will not account for switching in the tail of a real head field. This led onto a study of the ideal write point in BPM. In conventional recording theory the medium is designed to switch when the applied head field is at the position of its maximum gradient, which produces sharp transitions between magnetisation regions. A natural assumption in BPM is that the system could be optimised by setting the island switching field in a similar manner. This strategy of optimisation was investigated to see what gives the minimum error, or maximum write-window. It was concluded that optimisation could not be solely based on the maximum head field gradient, furthermore assuming the shape of the head field from this point will not produce an accurate estimation of the error in a BPM system.

Thesis (M. Eng.)--Massachusetts Institute of Technology, Dept. of Materials Science and Engineering, 2007.
Includes bibliographical references (p. 60-61).
The hard disk industry has traditionally stayed competitive by competing on the means of price alone by cutting down aggressively on cost via increase of areal density. Continuing increases in the areal density of hard disk drives will be limited by thermal instability of the thin film medium and is estimated to be limited to about 500Gb/in2. Patterned media, in which data are stored in an array of single.domain magnetic particles, have been suggested as a means to overcome this limitation and to enable recording densities greater than ITb/in2. However, the implementation of patterned media requires fabrication of sub-50-nm features over large areas and the design of recording systems that differ from those used in conventional hard drives. This report discusses the challenges facing patterned media, the fabrication of arrays of ́small magnetic particles and their magnetic properties. The practical implementation of patterned media recording schemes is assessed via technology estimates and cost analysis.
by Vibin Aravindakshan.
M.Eng.

Bit-Patterned Media (BPM) has been recognised as one of the candidate technologies to achieve an areal density beyond 1Tb/in2 by fabricating single-domain islands out of continuous magnetic media. Though much attention has been focused on the fabrication of BPM, existing lithography techniques demonstrate difficulties in producing uniform islands over large areas cost effectively; the resulting fabricated islands often vary in position and size. The primary purpose of the research documented in this thesis is to investigate the issue of island geometry variations on the data recovery process from a perpendicular patterned media with head and media configurations optimised to achieve an areal density of 1Tb/in2. In order to achieve the research aim, a read channel model has been implemented as a platform to evaluate the read channel performance numerically. It can be also altered to investigate new read channel designs. The simulated results demonstrate that island geometry variations have a detrimental effect on read channel performance. It has shown that a BPM system can be tolerant to island position variations, but more effort needs to be paid to the effect that island size variations have on the read channel performance. A new read channel design revolving around the design of a modified trellis has been proposed for use in the Viterbi detector in order to combat the effect of island geometry variations. The modified trellis for island position variations results in extra states and branches compared to the standard trellis, while the modified trellis for island size variations results in only extra branches. The novel read channel designs demonstrate an improved read channel performance in the presence of island geometry variations even with increasing amounts of island position and size variations. There are two ways to obtain the read channel performance in terms of the bit-error-rate (BER): a) by running a numerical Monte-Carlo simulation to count the number of bits in error at the output of the read channel model and b) using an analytical approach to calculate the BER by approximating the noise into a known distribution. It is shown that both ways demonstrate very similar results, which indicates as long as the distribution of the noise present in read channel model is predictable, the analytical approach can evaluate the BER performance more efficiently, especially when the BER is low. However, the Monte-Carlo simulation is still useful for understanding of the correlation of the errors. Novel trellis proposed in this work will contribute to the commercial development of BPM in two ways: a) to improve the data recovery process in BPM systems, b) to allow a tolerance of 10% size variations for the existing fabrication techniques.

For the past 50 years, the magnetic storage industry has been the ultimate provider, covering the ever-expanding needs of digital mass storage. Up to now, scaling to smaller dimensions has been the core approach for achieving higher areal densities in conventional media. However, recent studies have shown that further miniaturisation is physically bound by superparamagnetic effects. Bit patterned media (BPM) is one of the most promising solutions for extending the areal densities beyond 1Tbit/in². The ability to magnetically characterise novel BPM is a key requirement for its future commercialisation. The work presented in this thesis describes the investigation of the Magneto-Optic Kerr Effect (MOKE) and the Anomalous Hall Effect (AHE) techniques, used in the characterisation of BPM samples. These samples were produced as part of this work using a customised subtractive fabrication process. Continuous thin magnetic films with Ptseed(10nm)/[Co(0.4nm)/Pt(1nm)]x15 composition and perpendicular anisotropy, were deposited using electron-beam (e-beam) evaporation, and subsequently patterned into magnetic nano-islands through means of e-beam lithography and Ar⁺ ion milling. In terms of the MOKE technique, a fully customised polar MOKE system has been developed and successfully used to observe the hysteretic behaviour of magnetic nano-island arrays with varying dimensions. An expected reduction in the MOKE signal due to pattering has been observed, as well as an additional signal reduction due to the scattering effect arising from the non-vertical sidewalls of the dome-shaped islands. In the case of islands with improved shape profile, the magnetic reversal of BPM arrays with islands sizes down to 35nm has been successfully detected, demonstrating a sensitivity of approximately 6x10⁻¹³emu for the MOKE system. In terms of the AHE technique, Au Hall crosses were deposited on top of the BPM arrays that had been previously characterised by MOKE, allowing the direct comparison and cross-verification of the results obtained by the two techniques. A revised Hall cross design, where the Hall crosses were generated by direct patterning of the Pt seed layer, has provided a significant improvement in AHE signal. This has allowed the detection of the magnetic reversal of individual sub-50nm magnetic islands, demonstrating a sensitivity of approximately 6.6x10⁻¹⁵emu for the AHE technique. The spatial sensitivity of these Hall cross structures has been experimentally determined, indicating a decrease in sensitivity with increasing distance from the cross centre and with decreasing island diameter. In conclusion, the sensitivity profile of Hall cross structures must be taken into account for the accurate interpretation of BPM characterisation results obtained by the AHE technique. Finally, some suggestions are outlined with regard to the future improvement of the developed characterisation techniques and the further continuation of the work presented in this thesis.

The present thesis is about the investigation of ferromagnetic thin film systems with respect to exchange coupling, magnetization reversal behavior and effects appearing in magnetic heterostructures, namely the exchange bias and the giant magnetoresistance effect. For this purpose, DC magnetron sputtered thin films and multilayers with perpendicular magnetic anisotropy were prepared on single crystalline and rigid as well as flexible amorphous substrates. The first part concentrates on magnetic data storage applications based on the combination of the concept of bit patterned media and three dimensional magnetic memory, consisting of at least two exchange decoupled ferromagnetic storage layers. Here, [Co/Pt] multilayers, revealing different magnetic anisotropies, have been applied as storage layers and as spacer material Pt and Ru was employed. By the characterization of the magnetization reversal behavior the exchange coupling in dependence of the spacer layer thickness was studied. Furthermore, with regard to the concept of bit patterned media, the layers were also grown on self-assembled silica particles, leading to an exchange decoupled single-domain magnetic dot array, which was studied by magnetic force microscope imaging and angular dependent magneto-optic Kerr effect magnetometry to evaluate the reversal mechanism and its dependence on the array dimensions, mainly the diameter of the silica particles and layer thicknesses. To complete the study, micromagnetic simulations were performed to access smaller dimensions and to investigate the dependence of intralayer as well as interlayer coupling on the magnetization reversal of the dot array with multiple storage layers. The second part focuses on the investigation of the giant magnetoresistance effect in systems with perpendicular magnetic anisotropy, where L10 -chemically ordered FePt alloys and [Co/Pt] as well as [Co/Pd] multilayers were utilized. In case of FePt, where high temperatures during the deposition are necessary to induce the chemical ordering, diffusion and alloying of the spacer material often prevent a sufficient exchange decoupling of the ferromagnetic layers. However, with Ru as spacer material a giant magnetoresistance effect could be achieved. Large improvements of the magnetoresistive behavior of such trilayer structures are presented for [Co/Pt] and [Co/Pd] multilayers, which can be deposited at room temperature not limiting the choice of spacer as well as substrate material. Furthermore, in systems consisting of one ferromagnet with perpendicular magnetic anisotropy and one ferromagnet with in-plane magnetic easy axis, a linear and almost hysteresis-free field dependence of the electrical resistance was observed and the behavior for various thickness series has been intensively studied. Finally, the corrosion resistance in dependence of the capping layer material as well as the magnetoresistance of a strained flexible pseudo-spin-valve structure is presented. In addition, in chapter 2.5.2 an experimental study of an improved crystal growth of FePt at comparable low temperatures by molecular beam epitaxy and further promoted by a surfactant mediated growth using Sb is shown. Auger electron spectroscopy as well as Rutherford backscattering spectrometry were carried out to confirm the surface segregation of Sb and magnetic characterization revealed an increase of magnetic anisotropy in comparison to reference layers without Sb
Die vorliegende Dissertation beschäftigt sich mit der Untersuchung ferromagnetischer Dünnschichtsysteme im Hinblick auf die Austauchkopplung, das Ummagnetisierungsverhalten und Effekte wie z.B. den Exchange Bias Effekt oder den Riesenmagnetwiderstandseffekt (GMR), welche in derartigen Heterostrukturen auftreten können. Die Probenpräparation erfolgte mittels DC Magnetronsputtern, wobei auf einkristallinen aber auch flexiblen sowie starren amorphen Substraten abgeschieden wurde. Im ersten Teil der Arbeit werden Untersuchungen mit dem Hintergrund einer Anwendung als magnetischer Datenträger vorgestellt. Konkret werden hier die Konzepte Bit Patterned Media (BPM) und 3D Speicher miteinander kombiniert. Letzteres Konzept basiert auf der Verwendung wenigstens zweier austauschentkoppelter ferromagnetischer Schichten, für welche [Co/Pt] Multilagen mit unterschiedlicher magnetischer Anisotropie verwendet wurden. Als Zwischenschichtmaterial diente Pt und Ru. Durch die Charakterisierung des Ummagnetisierungsverhaltens wurde die Austauschkopplung in Abhängigkeit der Zwischenschichtdicke untersucht. Darüber hinaus wurden jene Schichtstapel zur Realisierung des BPM-Konzeptes auf selbstangeordnete SiO2 Partikel mit unterschiedlichen Durchmessern aufgebracht, durch welche sich lateral austauschentkoppelte, eindomänige magnetische Nanostrukturen erzeugen lassen. Zur Untersuchung des Ummagnetisierungsverhaltens und der jeweiligen Größenabhängigkeiten (maßgeblich Durchmesser und Schichtdicke) wurden diese mittels Magnetkraftmikroskopie sowie winkelabhängiger magnetooptischer Kerr Effekt Magnetometrie untersucht. Zur weiteren Vertiefung des Verständnisses noch kleinerer Strukturgrößen erfolgten mikromagnetische Simulationen, bei denen die magnetischen Wechselwirkungen lateral (benachbarte 3D Elemente) als auch vertikal (Wechselwirkungen ferromagnetischer Schichten innerhalb eines 3D Elementes) im Interesse standen, sowie deren Auswirkungen auf das Ummagnetisierungsverhalten des gesamten Feldes. Der Fokus des zweiten Teils liegt auf der Untersuchung des Riesenmagnetwiderstandseffektes in Systemen mit senkrechter Sensitivität. Dafür sind ferromagnetische Schichten mit senkrechter magnetischer Anisotropie nötig, wobei hier die chemisch geordnete L10-Phase der FePt Legierung und [Co/Pt] sowie [Co/Pd] Multilagen Anwendung fanden. Für eine chemische Ordnung der FePt Legierung sind hohe Temperaturen während der Schichtabscheidung notwendig, welche eine hinreichende Austauschentkopplung beider ferromagnetischer Schichten meist nicht gewährleisten. Grund dafür sind einsetzende Diffusionsprozesse als auch Legierungsbildungen mit dem Zwischenschichtmaterial. In der vorliegenden Arbeit konnte der GMR Effekt daher ausschließlich mit einer Ru Zwischenschicht in FePt basierten Trilagensystemen nachgewiesen und charakterisiert werden. Enorme Verbesserungen der magnetoresistiven Eigenschaften werden im Anschluss für [Co/Pt] und vor allem [Co/Pd] Multilagen vorgestellt. Diese Schichtsysteme mit senkrechter magnetischer Anisotropie können bei Raumtemperatur präpariert werden und stellen daher keine weiteren Anforderungen an das Zwischenschichtmaterial sowie die verwendeten Substrate. Hier wurden neben Systemen mit ausschließlich senkrechter magnetischer Anisotropie auch Systeme mit gekreuzten magnetischen Anisotropien intensiv untersucht, da diese durch einen linearen und weitgehend hysteresefreien R(H) Verlauf imHinblick auf Sensoranwendungen enorme Vorteile bieten. Letztendlich wurde die Korrosionsbeständigkeit in Abhängigkeit des Deckschichtmaterials als auch die mechanische Belastbarkeit von auf flexiblen Substraten abgeschiedenen GMR-Schichtstapeln untersucht. Zusätzlich wird in Kapitel 2.5.2 eine experimentelle Studie zum Surfactant-gesteuerten Wachstum der FePt Legierung mittels Molekularstrahlepitaxie vorgestellt. Als Surfactant dient Sb, wodurch die Kristallinität bei geringer Depositionstemperatur deutlich verbessert werden konnte. Die Oberflächensegregation von Sb wurde mittels Auger Elektronenspektroskopie und Rutherford Rückstreuspektrometrie verifiziert und die Charakterisierung magnetischer Eigenschaften belegt einen Anstieg der magnetischen Anisotropieenergie im Vergleich zu Referenzproben ohne Sb

As the superparamagnetic limit is reached, the magnetic storage industry looks to circumvent the barrier by implementing patterned media (PM) as a viable means to store and access data. Chemical mechanical polishing (CMP) is a semiconductor fabrication technique used to planarize surfaces and is investigated as a method to ensure that the PM is polished to surface roughness parameters that allow the magnetic read/write head to move seamlessly across the PM. Results from this research have implications in feasibility studies of utilizing CMP as the main planarization technique for PM fabrication. Benchmark data on the output parameters of the CMP process, for bit patterned media (BPM), based on the machine process parameters, pad properties, and slurry characteristics are optimized. The research was conducted in a systematic manner in which the optimized parameters for each phase are utilized in future phases. The optimum results from each of the phases provide an overall optimum characterization for BPM CMP. Results on the CMP machine input parameters indicate that for optimal surface roughness and material removal, low polish pressures and high velocities should be used on the BPM. Pad characteristics were monitored by non destructive technique and results indicate much faster deterioration of all pad characteristics versus polish time of BPM when compared to IC CMP. The optimum pad for PM polishing was the IC 1400 dual layer Suba V pad with a shore hardness of 57, and a k-groove pattern. The final phase of polishing evaluated the slurry polishing properties and novel nanodiamond (ND) slurry was created and benchmarked on BPM. The resulting CMP output parameters were monitored and neither the ND slurry nor the thermally responsive polymer slurry performed better than the commercially available Cabot iCue slurry for MRR or surface roughness. Research results indicate CMP is a feasible planarization technique for PM fabrication, but successful implementation of CMP for planarizing PM must address the high initial start up cost, increase in the number of replacement pads, and increase in polishing time to reach the required surface roughness for magnetic storage devices.

Due to the ever-increasing worldwide consumption of memory for digital information, new technologies for higher capacity and faster data storage systems have been the focus of research and development. A step towards achieving higher data storage densities or magnetic recording media is the concept of bit patterned media, where the magnetic recording layer is divided up into magnetically isolated bit units. This approach is one of the most promising technologies for increasing data storage densities and could be implemented by nanostructuring the wafer. Therefore, the fabrication of the appropriate nanostructures on a small scale and then be able to manufacture these structures on an industrial scale is one of the problems where science and industry are working on a solution. In addition, the answer to the open question about the influence that patterning on the nano length scale has on the magnetic properties is of great interest. The main goal of this thesis is to answer the open question, which magnetic properties can be tailored by a modification of the surface texture on the nanometre length scale. For this purpose the following properties: anisotropy, remanence, coercivity, switching field distribution, saturation magnetisation, Gilbert damping, and inhomogeneous linebroadening were compared between planar two dimensional thin ferromagnetic films and three dimensional magnetic structures. In addition, the influences of the tailored morphology on the intergranular or the exchange coupling between the structures, which is called interdot exchange coupling, was investigated. For the ferromagnetic thin films, the focus of the investigations was on the granular CoCrPt:SiO2 and [Co/Pd] layer, which currently are the state-of-the-art material for magnetic data storage media. These materials are characterised by their high coercivity and high perpendicular anisotropy, which has a low spatial distribution in the preferred direction of magnetisation. In this work the pre-structured GaSb(001) substrate with self-assembled periodic nanocone structures at the surface are used. The preparation by ion beam erosion of these structures is simple, fast, and highly reproducible and therefore this method is particularly beneficial for fundamental research. To compare the 2D thin films with the 3D magnetic structures, besides the pre-structured specimen, planar samples were also fabricated. The first sample series prepared was coated by Py. Due to the fact that the magnetic properties of this material are well-known, it was also possible to do some OOMMF simulations in addition to the VNA-FMR and MOKE measurements. Afterwards two planar samples with CoCrPt and CoCrPt:SiO2 were prepared. The planar CoCrPt:SiO2 samples were Co+ ion implanted to study the influence of such irradiation on the intergranular and interdot exchange coupling, switching field distribution, and in particular on the spin dynamics. Moreover, both samples were measured by TRMOKE in order to obtain information about the spin dynamics. Subsequently, the perpendicular storage media materials CoCrPt:SiO2 and [Co/Pd] were deposited on a prestructured GaSb(001) nanocone substrate surface. These sample series were measured by MOKE, SQUID, and vector-VSM. The measurements demonstrate the influence of the periodicity and height of the nanocones on the intergranular and interdot exchange coupling. They also show the reorientation of the magnetisation with respect to the curvature of the substrate template and furthermore, the morphology-induced influences on the magnetic domains. From the comparison between the results for the planar and the pre-structured samples, a decrease of the interdot exchange coupling was observed, which scales together with the periodicity of the nanocone pattern. In addition, it was shown that for all samples with thin magnetic films on nanocones,the magnetisation aligns along the curvature of the underlying nanocone structure. For Py on nanocones, planar granular CoCrPt:SiO2, and planar granular CoCrPt, measurements by VNA-FMR and TRMOKE could be carried out, which yielded information about the spin dynamics. The results obtained for both of the planar sample are comparable to values from the literature for the Gilbert damping. The results for the Py samples showed that the commonly used 2D model resonance condition is, in case of a 3D magnetic structure, no longer valid due to the alignment of the magnetisation along the underlying substrate structure and therefore an new model has to be derived
Aufgrund des weltweiten, immer weiter steigenden Bedarfs an Speicherplatz von digitalen Information, sind neue Technologien für größere und schnellere Speichermedien im Fokus von Forschung und Entwicklung. Ein Schritt hin zu einer höheren Speicherdichte in der magnetischen Datenspeicherung ist dabei das sogenannte Konzept der ”Bit patterned media”, das definierte Informationseinheiten auf regelmäßig angeordneten Nanostrukturen beschreibt. Dieser Ansatz ist einer der derzeit vielversprechendsten Optionen die Speicherdichte zu erhöhen. Dabei ist die Herstellung der benötigten Nanostrukturen und deren Skalierung hin zu makroskopischen Dimensionen eines der Probleme an deren Lösung die Wissenschaft und Industrie derzeit arbeitet. Desweiteren ist die Antwort auf die noch offene Frage nach der Beeinflussung der nanoskaligen Strukturen auf die magnetischen Eigenschaften von großem Interesse. Das Hauptziel in dieser Arbeit ist es, einen Beitrag zur Beantwortung der Frage, welche magnetischen Eigenschaften sich durch eine Veränderung der Oberflächenstruktur im Nanometerbereich beeinflussen lassen, zu leisten. Hierzu wurden die folgenden Eigenschaften, wie zum Beispiel die Anisotropie, Remanenz,Koerzitivität, Schaltfeldverteilung, Sättigungsmagnetisierung, Gilbertdämpfung und inhomogene Linienverbreiterung von planaren zweidimensionalen dünnen ferromagnetische Schichten mit denen von dreidimensionalen magnetischen Strukturen verglichen. Zusätzlich wurde der Einfluss der angegpassten Morphologie auf die intergranularen- beziehungsweise auf die zwischen den Strukturen wirkende (interdot) Austauschkopplung untersucht. Der Hauptaugenmerk bei den ferromagnetisch dünnen Schichten lag dabei auf den granularen CoCrPt:SiO2 und [Co/Pd] Filmen, die heutzutage ein Standardmaterial für die magnetischen Speichermedien darstellen. Diese Materialien zeichnen sich durch eine hohe Koerzivität und senkrechte Anisotropie, mit geringer räumlicher Verteilung der Vorzugsrichtung der Magnetisierung, aus. Die hier vorgestellten vorstrukturierten GaSb(001) Substrate mit selbstordnenden periodischen Nanokegeln auf der Oberfläche, sind mittels Ionenstrahlerosion einfach, schnell und sehr gut reproduzierbar herzustellen. Deshalb ist diese Methode besonders für die Grundlagenforschung von Vorteil. Um einen Vergleich zwischen 2D Filmen und 3D Strukturen ziehen zu können, wurden neben den vorstrukturierten Substraten auch planare Proben beschichtet. Eine erste Versuchsreihe wurde mit einem dünnen Py Film präpariert. Da dessen magnetische Eigenschaften wohlbekannt sind, konnten neben den Untersuchungen mit VNA-FMR und MOKE auch einige OOMF Simulationen erstellt werden. Danach wurden zwei Proben mit planarem CoCrPt beziehungsweise CoCrPt:SiO2 untersucht. Bei den planaren CoCrPt:SiO2 Proben wurden außerdem noch Co+ Ionen implantiert, um deren Auswirkungen auf die intergranulare Austauschkopplung, Schaltfeldverteilung und besonders auf die Spindynamik zu bestimmen. Bei beiden Probensystemen konnte zusätzlich die Spindynamik mittels zeitaufgelöstem MOKE gemessen werden. Im Anschluss wurden die beiden senkrechten Speichermedien CoCrPt:SiO2 and [Co/Pd] auf Substraten mit Nanokegeln vorstrukturierten GaSb(001) Oberflächen abgeschieden. Diese Proben wurden mit MFM, MOKE, SQUID und Vektor-VSM vermessen. Aus den Messungen konnnten dann die Einflüsse auf die intergranulare- beziehungsweise interdot Austauschkopplung in Abhängigkeit von der Periodizität und Höhe der Nanokegel bestimmt werden, sowie die Umorientierung der Magnetisierung bezüglich der Substratkrümmung und den Morphologie induzierten Einfluss auf die magnetischen Domänen. Anhand der Vergleiche zwischen den Messungen der planaren und den vorstrukturierten Proben konnte eine Verringerung der Austauschkopplung zwischen den Strukturen gezeigt werden, die mit der Nanokegelstrukturperiodizität skaliert. Außerdem wurde in allen dünnen magnetischen Filmen auf Nanokegeln gezeigt, dass die Magnetisierung sich in Abhängigkeit der darunterliegenden Struktur ausrichtet. Bei den Py auf Nanokegeln, den planaren CoCrPt und dem planaren CoCrPt:SiO2 Proben konnten außerdem mit VNA-FMR und TRMOKE Informationen bezüglich der Spindynamik gemessen werden. Die erzielten Ergebnisse, der beiden planaren Proben, sind vergleichbar mit denen, aus der Literatur bekannten Werten, für die Gilbertdämpfung. Darüber hinaus wurde durch die Messungen an den Py Proben gezeigt, dass die Theorie, des bisher genutzten 2D Modells, nicht mehr gültig ist, da sich die Magnetisierung entlang der Substratstruktur ausrichtet, und deshalb ein neues Model aufgestellt werden muss

Due to the ever-increasing worldwide consumption of memory for digital information, new technologies for higher capacity and faster data storage systems have been the focus of research and development. A step towards achieving higher data storage densities or magnetic recording media is the concept of bit patterned media, where the magnetic recording layer is divided up into magnetically isolated bit units. This approach is one of the most promising technologies for increasing data storage densities and could be implemented by nanostructuring the wafer. Therefore, the fabrication of the appropriate nanostructures on a small scale and then be able to manufacture these structures on an industrial scale is one of the problems where science and industry are working on a solution. In addition, the answer to the open question about the influence that patterning on the nano length scale has on the magnetic properties is of great interest. The main goal of this thesis is to answer the open question, which magnetic properties can be tailored by a modification of the surface texture on the nanometre length scale. For this purpose the following properties: anisotropy, remanence, coercivity, switching field distribution, saturation magnetisation, Gilbert damping, and inhomogeneous linebroadening were compared between planar two dimensional thin ferromagnetic films and three dimensional magnetic structures. In addition, the influences of the tailored morphology on the intergranular or the exchange coupling between the structures, which is called interdot exchange coupling, was investigated. For the ferromagnetic thin films, the focus of the investigations was on the granular CoCrPt:SiO2 and [Co/Pd] layer, which currently are the state-of-the-art material for magnetic data storage media. These materials are characterised by their high coercivity and high perpendicular anisotropy, which has a low spatial distribution in the preferred direction of magnetisation. In this work the pre-structured GaSb(001) substrate with self-assembled periodic nanocone structures at the surface are used. The preparation by ion beam erosion of these structures is simple, fast, and highly reproducible and therefore this method is particularly beneficial for fundamental research. To compare the 2D thin films with the 3D magnetic structures, besides the pre-structured specimen, planar samples were also fabricated. The first sample series prepared was coated by Py. Due to the fact that the magnetic properties of this material are well-known, it was also possible to do some OOMMF simulations in addition to the VNA-FMR and MOKE measurements. Afterwards two planar samples with CoCrPt and CoCrPt:SiO2 were prepared. The planar CoCrPt:SiO2 samples were Co+ ion implanted to study the influence of such irradiation on the intergranular and interdot exchange coupling, switching field distribution, and in particular on the spin dynamics. Moreover, both samples were measured by TRMOKE in order to obtain information about the spin dynamics. Subsequently, the perpendicular storage media materials CoCrPt:SiO2 and [Co/Pd] were deposited on a prestructured GaSb(001) nanocone substrate surface. These sample series were measured by MOKE, SQUID, and vector-VSM. The measurements demonstrate the influence of the periodicity and height of the nanocones on the intergranular and interdot exchange coupling. They also show the reorientation of the magnetisation with respect to the curvature of the substrate template and furthermore, the morphology-induced influences on the magnetic domains. From the comparison between the results for the planar and the pre-structured samples, a decrease of the interdot exchange coupling was observed, which scales together with the periodicity of the nanocone pattern. In addition, it was shown that for all samples with thin magnetic films on nanocones,the magnetisation aligns along the curvature of the underlying nanocone structure. For Py on nanocones, planar granular CoCrPt:SiO2, and planar granular CoCrPt, measurements by VNA-FMR and TRMOKE could be carried out, which yielded information about the spin dynamics. The results obtained for both of the planar sample are comparable to values from the literature for the Gilbert damping. The results for the Py samples showed that the commonly used 2D model resonance condition is, in case of a 3D magnetic structure, no longer valid due to the alignment of the magnetisation along the underlying substrate structure and therefore an new model has to be derived.
Aufgrund des weltweiten, immer weiter steigenden Bedarfs an Speicherplatz von digitalen Information, sind neue Technologien für größere und schnellere Speichermedien im Fokus von Forschung und Entwicklung. Ein Schritt hin zu einer höheren Speicherdichte in der magnetischen Datenspeicherung ist dabei das sogenannte Konzept der ”Bit patterned media”, das definierte Informationseinheiten auf regelmäßig angeordneten Nanostrukturen beschreibt. Dieser Ansatz ist einer der derzeit vielversprechendsten Optionen die Speicherdichte zu erhöhen. Dabei ist die Herstellung der benötigten Nanostrukturen und deren Skalierung hin zu makroskopischen Dimensionen eines der Probleme an deren Lösung die Wissenschaft und Industrie derzeit arbeitet. Desweiteren ist die Antwort auf die noch offene Frage nach der Beeinflussung der nanoskaligen Strukturen auf die magnetischen Eigenschaften von großem Interesse. Das Hauptziel in dieser Arbeit ist es, einen Beitrag zur Beantwortung der Frage, welche magnetischen Eigenschaften sich durch eine Veränderung der Oberflächenstruktur im Nanometerbereich beeinflussen lassen, zu leisten. Hierzu wurden die folgenden Eigenschaften, wie zum Beispiel die Anisotropie, Remanenz,Koerzitivität, Schaltfeldverteilung, Sättigungsmagnetisierung, Gilbertdämpfung und inhomogene Linienverbreiterung von planaren zweidimensionalen dünnen ferromagnetische Schichten mit denen von dreidimensionalen magnetischen Strukturen verglichen. Zusätzlich wurde der Einfluss der angegpassten Morphologie auf die intergranularen- beziehungsweise auf die zwischen den Strukturen wirkende (interdot) Austauschkopplung untersucht. Der Hauptaugenmerk bei den ferromagnetisch dünnen Schichten lag dabei auf den granularen CoCrPt:SiO2 und [Co/Pd] Filmen, die heutzutage ein Standardmaterial für die magnetischen Speichermedien darstellen. Diese Materialien zeichnen sich durch eine hohe Koerzivität und senkrechte Anisotropie, mit geringer räumlicher Verteilung der Vorzugsrichtung der Magnetisierung, aus. Die hier vorgestellten vorstrukturierten GaSb(001) Substrate mit selbstordnenden periodischen Nanokegeln auf der Oberfläche, sind mittels Ionenstrahlerosion einfach, schnell und sehr gut reproduzierbar herzustellen. Deshalb ist diese Methode besonders für die Grundlagenforschung von Vorteil. Um einen Vergleich zwischen 2D Filmen und 3D Strukturen ziehen zu können, wurden neben den vorstrukturierten Substraten auch planare Proben beschichtet. Eine erste Versuchsreihe wurde mit einem dünnen Py Film präpariert. Da dessen magnetische Eigenschaften wohlbekannt sind, konnten neben den Untersuchungen mit VNA-FMR und MOKE auch einige OOMF Simulationen erstellt werden. Danach wurden zwei Proben mit planarem CoCrPt beziehungsweise CoCrPt:SiO2 untersucht. Bei den planaren CoCrPt:SiO2 Proben wurden außerdem noch Co+ Ionen implantiert, um deren Auswirkungen auf die intergranulare Austauschkopplung, Schaltfeldverteilung und besonders auf die Spindynamik zu bestimmen. Bei beiden Probensystemen konnte zusätzlich die Spindynamik mittels zeitaufgelöstem MOKE gemessen werden. Im Anschluss wurden die beiden senkrechten Speichermedien CoCrPt:SiO2 and [Co/Pd] auf Substraten mit Nanokegeln vorstrukturierten GaSb(001) Oberflächen abgeschieden. Diese Proben wurden mit MFM, MOKE, SQUID und Vektor-VSM vermessen. Aus den Messungen konnnten dann die Einflüsse auf die intergranulare- beziehungsweise interdot Austauschkopplung in Abhängigkeit von der Periodizität und Höhe der Nanokegel bestimmt werden, sowie die Umorientierung der Magnetisierung bezüglich der Substratkrümmung und den Morphologie induzierten Einfluss auf die magnetischen Domänen. Anhand der Vergleiche zwischen den Messungen der planaren und den vorstrukturierten Proben konnte eine Verringerung der Austauschkopplung zwischen den Strukturen gezeigt werden, die mit der Nanokegelstrukturperiodizität skaliert. Außerdem wurde in allen dünnen magnetischen Filmen auf Nanokegeln gezeigt, dass die Magnetisierung sich in Abhängigkeit der darunterliegenden Struktur ausrichtet. Bei den Py auf Nanokegeln, den planaren CoCrPt und dem planaren CoCrPt:SiO2 Proben konnten außerdem mit VNA-FMR und TRMOKE Informationen bezüglich der Spindynamik gemessen werden. Die erzielten Ergebnisse, der beiden planaren Proben, sind vergleichbar mit denen, aus der Literatur bekannten Werten, für die Gilbertdämpfung. Darüber hinaus wurde durch die Messungen an den Py Proben gezeigt, dass die Theorie, des bisher genutzten 2D Modells, nicht mehr gültig ist, da sich die Magnetisierung entlang der Substratstruktur ausrichtet, und deshalb ein neues Model aufgestellt werden muss.

In the thesis at hand, different concepts of magnetic recording were investigated both from an experimental and theoretical point of view. On the one hand, micromagnetic simulations of bit patterned media were performed examining the influence of magnetic and geometrical parameters on the magnetization reversal mechanism of the bit array. In this regard, the recording concept called exchange coupled composite (ECC) media was applied in combination with bit patterned media (BPM). It was demonstrated that ECC/BPM is superior in terms of narrowing the SFD which is vital for the implementation of BPM as a recording scheme in magnetic data storage deviced. Moreover, the stability of the magnetic state was calculated for single nanomagnets using the nudged elastic band algorithm. It was found out that the magnetic and geometrical properties have a severe influence on both, the energy barrier for magnetization reversal and the magnetization reversal process of the single nanomagnets. On the other hand, experimental studies of granular CoCrPt:SiO2 films deposited on self-assembled arrays of SiO2 nanoparticles with a size from 10 nm to 330 nm have been carried out, showing a distinct size-dependence of the coercive field and remanent magnetization with changing nanoparticle size. Moreover, these films have been irradiated with Co+ ions with different fluences, resulting in a change of the magnetic properties of the films due to both a change of the intergranular exchange coupling of the film and a degredation of the magnetic layers at higher irradiation fluences.

The present thesis is about the investigation of ferromagnetic thin film systems with respect to exchange coupling, magnetization reversal behavior and effects appearing in magnetic heterostructures, namely the exchange bias and the giant magnetoresistance effect. For this purpose, DC magnetron sputtered thin films and multilayers with perpendicular magnetic anisotropy were prepared on single crystalline and rigid as well as flexible amorphous substrates. The first part concentrates on magnetic data storage applications based on the combination of the concept of bit patterned media and three dimensional magnetic memory, consisting of at least two exchange decoupled ferromagnetic storage layers. Here, [Co/Pt] multilayers, revealing different magnetic anisotropies, have been applied as storage layers and as spacer material Pt and Ru was employed. By the characterization of the magnetization reversal behavior the exchange coupling in dependence of the spacer layer thickness was studied. Furthermore, with regard to the concept of bit patterned media, the layers were also grown on self-assembled silica particles, leading to an exchange decoupled single-domain magnetic dot array, which was studied by magnetic force microscope imaging and angular dependent magneto-optic Kerr effect magnetometry to evaluate the reversal mechanism and its dependence on the array dimensions, mainly the diameter of the silica particles and layer thicknesses. To complete the study, micromagnetic simulations were performed to access smaller dimensions and to investigate the dependence of intralayer as well as interlayer coupling on the magnetization reversal of the dot array with multiple storage layers. The second part focuses on the investigation of the giant magnetoresistance effect in systems with perpendicular magnetic anisotropy, where L10 -chemically ordered FePt alloys and [Co/Pt] as well as [Co/Pd] multilayers were utilized. In case of FePt, where high temperatures during the deposition are necessary to induce the chemical ordering, diffusion and alloying of the spacer material often prevent a sufficient exchange decoupling of the ferromagnetic layers. However, with Ru as spacer material a giant magnetoresistance effect could be achieved. Large improvements of the magnetoresistive behavior of such trilayer structures are presented for [Co/Pt] and [Co/Pd] multilayers, which can be deposited at room temperature not limiting the choice of spacer as well as substrate material. Furthermore, in systems consisting of one ferromagnet with perpendicular magnetic anisotropy and one ferromagnet with in-plane magnetic easy axis, a linear and almost hysteresis-free field dependence of the electrical resistance was observed and the behavior for various thickness series has been intensively studied. Finally, the corrosion resistance in dependence of the capping layer material as well as the magnetoresistance of a strained flexible pseudo-spin-valve structure is presented. In addition, in chapter 2.5.2 an experimental study of an improved crystal growth of FePt at comparable low temperatures by molecular beam epitaxy and further promoted by a surfactant mediated growth using Sb is shown. Auger electron spectroscopy as well as Rutherford backscattering spectrometry were carried out to confirm the surface segregation of Sb and magnetic characterization revealed an increase of magnetic anisotropy in comparison to reference layers without Sb.
Die vorliegende Dissertation beschäftigt sich mit der Untersuchung ferromagnetischer Dünnschichtsysteme im Hinblick auf die Austauchkopplung, das Ummagnetisierungsverhalten und Effekte wie z.B. den Exchange Bias Effekt oder den Riesenmagnetwiderstandseffekt (GMR), welche in derartigen Heterostrukturen auftreten können. Die Probenpräparation erfolgte mittels DC Magnetronsputtern, wobei auf einkristallinen aber auch flexiblen sowie starren amorphen Substraten abgeschieden wurde. Im ersten Teil der Arbeit werden Untersuchungen mit dem Hintergrund einer Anwendung als magnetischer Datenträger vorgestellt. Konkret werden hier die Konzepte Bit Patterned Media (BPM) und 3D Speicher miteinander kombiniert. Letzteres Konzept basiert auf der Verwendung wenigstens zweier austauschentkoppelter ferromagnetischer Schichten, für welche [Co/Pt] Multilagen mit unterschiedlicher magnetischer Anisotropie verwendet wurden. Als Zwischenschichtmaterial diente Pt und Ru. Durch die Charakterisierung des Ummagnetisierungsverhaltens wurde die Austauschkopplung in Abhängigkeit der Zwischenschichtdicke untersucht. Darüber hinaus wurden jene Schichtstapel zur Realisierung des BPM-Konzeptes auf selbstangeordnete SiO2 Partikel mit unterschiedlichen Durchmessern aufgebracht, durch welche sich lateral austauschentkoppelte, eindomänige magnetische Nanostrukturen erzeugen lassen. Zur Untersuchung des Ummagnetisierungsverhaltens und der jeweiligen Größenabhängigkeiten (maßgeblich Durchmesser und Schichtdicke) wurden diese mittels Magnetkraftmikroskopie sowie winkelabhängiger magnetooptischer Kerr Effekt Magnetometrie untersucht. Zur weiteren Vertiefung des Verständnisses noch kleinerer Strukturgrößen erfolgten mikromagnetische Simulationen, bei denen die magnetischen Wechselwirkungen lateral (benachbarte 3D Elemente) als auch vertikal (Wechselwirkungen ferromagnetischer Schichten innerhalb eines 3D Elementes) im Interesse standen, sowie deren Auswirkungen auf das Ummagnetisierungsverhalten des gesamten Feldes. Der Fokus des zweiten Teils liegt auf der Untersuchung des Riesenmagnetwiderstandseffektes in Systemen mit senkrechter Sensitivität. Dafür sind ferromagnetische Schichten mit senkrechter magnetischer Anisotropie nötig, wobei hier die chemisch geordnete L10-Phase der FePt Legierung und [Co/Pt] sowie [Co/Pd] Multilagen Anwendung fanden. Für eine chemische Ordnung der FePt Legierung sind hohe Temperaturen während der Schichtabscheidung notwendig, welche eine hinreichende Austauschentkopplung beider ferromagnetischer Schichten meist nicht gewährleisten. Grund dafür sind einsetzende Diffusionsprozesse als auch Legierungsbildungen mit dem Zwischenschichtmaterial. In der vorliegenden Arbeit konnte der GMR Effekt daher ausschließlich mit einer Ru Zwischenschicht in FePt basierten Trilagensystemen nachgewiesen und charakterisiert werden. Enorme Verbesserungen der magnetoresistiven Eigenschaften werden im Anschluss für [Co/Pt] und vor allem [Co/Pd] Multilagen vorgestellt. Diese Schichtsysteme mit senkrechter magnetischer Anisotropie können bei Raumtemperatur präpariert werden und stellen daher keine weiteren Anforderungen an das Zwischenschichtmaterial sowie die verwendeten Substrate. Hier wurden neben Systemen mit ausschließlich senkrechter magnetischer Anisotropie auch Systeme mit gekreuzten magnetischen Anisotropien intensiv untersucht, da diese durch einen linearen und weitgehend hysteresefreien R(H) Verlauf imHinblick auf Sensoranwendungen enorme Vorteile bieten. Letztendlich wurde die Korrosionsbeständigkeit in Abhängigkeit des Deckschichtmaterials als auch die mechanische Belastbarkeit von auf flexiblen Substraten abgeschiedenen GMR-Schichtstapeln untersucht. Zusätzlich wird in Kapitel 2.5.2 eine experimentelle Studie zum Surfactant-gesteuerten Wachstum der FePt Legierung mittels Molekularstrahlepitaxie vorgestellt. Als Surfactant dient Sb, wodurch die Kristallinität bei geringer Depositionstemperatur deutlich verbessert werden konnte. Die Oberflächensegregation von Sb wurde mittels Auger Elektronenspektroskopie und Rutherford Rückstreuspektrometrie verifiziert und die Charakterisierung magnetischer Eigenschaften belegt einen Anstieg der magnetischen Anisotropieenergie im Vergleich zu Referenzproben ohne Sb.

Les travaux élaborés dans cette thèse ont pour objectif de caractériser les propriétés magnétiques et structurales de nanostructures magnétiques obtenues par une nouvelle méthode de synthèse mixte physique/chimique, dite croissance hybride. La première partie du travail réalisé consiste en l’élaboration de films minces métalliques sur substrats par pulvérisation cathodique. Sur ces films minces, la synthèse chimique par voie organométallique aboutit à des réseaux de nanofils de Co monocristallins hcp, ultra-denses, ou des films nanostructurés de Fe. Les observations MEB/MET et les mesures de diffraction de rayons X réalisées sur les substrats montrent le fort impact induit par la cristallinité de la couche mince sur la morphologie et la direction de croissance des nanostructures magnétiques.Les mesures magnétiques réalisées sur des réseaux de nanofils de Co montrent une forte anisotropie magnétique perpendiculaire au substrat. Cela est obtenu grâce à l’anisotropie magnétocristalline du Co hcp (avec l’axe c parallèle à l’axe du fil) qui s’ajoute à l’anisotropie de forme. L’aimantation thermiquement stable, semble suivre un régime de retournement cohérent, régime non observé dans les structures polycristallines. L’organisation de ces nanostructures, leur grande densité et la stabilité de leur aimantation font de ce réseau un bon candidat aux applications de médias d’enregistrement magnétique à forte densité
The elaboration of this thesis aims to characterize the magnetic and structural properties of magnetic nanostructures obtained by a new mixed physical / chemical synthesis method, called hybrid growth. The first part of the work consists in the development of thin metal films on substrates by cathode sputtering. Furthermore, the chemical synthesis conducted by organometallic chemistry on those thin films, results in an array of ultra-dense Co monocristallins hcp nanowires, or nanostructured Fe films. Additionally, The SEM/TEM observations and the X-ray diffraction measurements conducted on the substrates and induced by the crystlalline structure of the thin film, show the high impact on the magnetic nanostructures morphology and growth direction.Moreover, the magnetic measurements executed on the Co nanowires array show a strong magnetic anisotropy perpendicular to the substrate. This observation is obtained due to the magnetocrystalline anisotropy acting along the nanowire axis (Co hcp structure with the c axis parallel to the nanowire axis) in the same direction of the nanowires shape anisotropy. The magnetization within these structures is thermally stable. It follows a coherent magnetization reversal mode that has not been observed in the polycrystalline structures up to now. Finally, the self-organization of the nanowires as well as their high density and stable magnetization nominate this system for their application in high density magnetic storage devices

Data storage in current hard disk drives is limited by three factors. These are thermal stability of recorded data, the ability to store data, and the ability to read back the stored data. An attempt to alleviate one factor can affect others. This ultimately limits magnetic recording densities that can be achieved using traditional forms of data storage. In order to advance magnetic recording and postpone these inhibiting factors, new approaches are required. One approach is recording on Bit Patterned Media (BPM) where the medium is patterned into nanometer-sized magnetic islands where each stores a binary digit.This thesis presents a statistical model of write errors in BPM composed of single domain islands. The model includes thermal activation in a calculation of write errors without resorting to time consuming micromagnetic simulations of huge populations of islands. The model incorporates distributions of position, magnetic and geometric properties of islands. In order to study the impact of island geometry variations on the recording performance of BPM systems, the magnetometric demagnetising factors for a truncated elliptic cone, a generalised geometry that reasonably describe most proposed island shapes, were derived analytically.The inclusion of thermal activation was enabled by an analytic derivation of the energy barrier for a single domain island. The energy barrier is used in a calculation of transition rates that enable the calculation of error rates. The model has been used to study write-error performance of BPM systems having distributions of position, geometric and magnetic property variations. Results showed that island intrinsic anisotropy and position variations have a larger impact on write-error performance than geometric variations.The model was also used to study thermally activated Adjacent Track Erasure (ATE) for a specific write head. The write head had a rectangular main pole of 13 by 40 nm (cross-track x down-track) with pole trailing shield gap of 5 nm and pole side shield gap of 10 nm. The distance from the pole to the top surface of the medium was 5 nm, the medium was 10 nm thick and there was a 2 nm interlayer between the soft underlayer (SUL) and the medium, making a total SUL to pole spacing of 17 nm. The results showed that ATE would be a major problem and that cross-track head field gradients need to be more tightly controlled than down-track. With the write head used, recording at 1 Tb/in² would be possible on single domain islands.

Chemically ordered FePt is one of the most promising materials to reach the ultimate limitations in storage density of future magnetic recording devices due to its high uniaxial magnetocrystalline anisotropy and a corrosion resistance superior to rare-earth based magnets. In this study, FePt and FePt/Cu bilayers have been sputter deposited at room temperature onto thermally oxidized silicon wafers, glass substrates and self-assembled arrays of spherical SiO2 particles with diameters down to 10 nm. Millisecond flash lamp annealing, as well as conventional rapid thermal annealing was employed to induce the phase transformation from the chemically disordered A1 phase into the chemically ordered L10 phase. The influence of the annealing temperature, annealing time and the film thickness on the ordering transformation and (001) texture evolution of FePt films with near equiatomic composition was studied. Whereas flash lamp annealed FePt films exhibit a polycrystalline morphology with high chemical L10 order, rapid thermal annealing can lead to the formation of chemically ordered FePt fifilms with (001) texture on amorphous SiO2/Si substrates. The resultant high perpendicular magnetic anisotropy and large coercivities up to 40 kOe are demonstrated. Simultaneuosly to the ordering transformation, rapid thermal annealing to temperatures exceeding 600 °C leads to a break up of the continuous FePt film into separated islands. This dewetting behavior was utilized to create regular arrays of FePt nanostructures on SiO2 particle templates with periods down to 50 nm. The addition of Cu improves the (001) texture formation and chemcial ordering for annealing temperatures T < 600 °C. In addition, the magnetic anisotropy and the coercivity of the ternary FePtCu alloy can be effectively tailored by adjusting the Cu content. The prospects of FePtCu based exchange spring media, as well as the magnetic properties of FePtCu nanostructures fabricated using e-beam and nanoimprint lithography have been investigated.

This thesis discusses the full scope of a project exploring the physics of hierarchical clusters of interacting nanomagnets. These clusters may be relevant for novel applications such as multilevel data storage devices. The work can be grouped into three main activities: micromagnetic simulation, fabrication and characterization of proof-of-concept prototype devices, and efforts to scale down the structures by creating the hierarchical structures with the aid of diblock copolymer self assembly. Theoretical micromagnetic studies and simulations based on Landau-Lifshitz-Gilbert (LLG) equation were conducted on nanoscale single domain magnetic entities. For the simulated nanomagnet clusters with perpendicular uniaxial anisotropy, the simulation showed the switching field distributions, the stability of the magnetostatic states with distinctive total cluster perpendicular moments, and the stepwise magnetic switching curves. For simulated nanomagnet clusters with in-plane shape anisotropy, the simulation showed the stepwise switching behaviors governed by thermal agitation and cluster configurations. Proof-of-concept cluster devices with three interacting Co nanomagnets were fabricated by e-beam lithography (EBL) and pulse-reverse electrochemical deposition (PRECD). EBL patterning on a suspended 100 nm SiN membrane showed improved lateral lithography resolution to 30 nm. The Co nanomagnets deposited using the PRECD method showed perpendicular anisotropy. The switching experiments with external applied fields were able to switch the Co nanomagnets through the four magnetostatic states with distinctive total perpendicular cluster magnetization, and proved the feasibility of multilevel data storage devices based on the cluster concept. Shrinking the structures size was experimented by the aid of diblock copolymer. Thick poly(styrene)-b-poly(methyl methacrylate) (PS-b-PMMA) diblock copolymer templates aligned with external electrical field were used to fabricate long Ni/Fe magnetic nanowire array, dominant shape anisotropy was observed and compared to the result from previously reported Co nanowire array with strong crystalline anisotropy. Guided diblock copolymer poly(styrene)-b-poly(4-vinyl pyridine) (PS- b-P4VP) self assembly was performed to generate clustered microdomains. Direct e-beam patterning on PS-b-P4VP thin film showed precise and arbitrary patterning on the lateral ordering of the self assembly. Graphoepitaxy of self-assembled PS-b-P4VP copolymers on isolated SiN triangular plateaus successfully resulted in the exact clusters of three microdomains. Theoretical consideration and system modeling based on the micellar configuration of the microdomains were done, and the distribution of the cluster’s size and number of elements were explained qualitatively.

Chemically ordered FePt is one of the most promising materials to reach the ultimate limitations in storage density of future magnetic recording devices due to its high uniaxial magnetocrystalline anisotropy and a corrosion resistance superior to rare-earth based magnets. In this study, FePt and FePt/Cu bilayers have been sputter deposited at room temperature onto thermally oxidized silicon wafers, glass substrates and self-assembled arrays of spherical SiO2 particles with diameters down to 10 nm. Millisecond flash lamp annealing, as well as conventional rapid thermal annealing was employed to induce the phase transformation from the chemically disordered A1 phase into the chemically ordered L10 phase. The influence of the annealing temperature, annealing time and the film thickness on the ordering transformation and (001) texture evolution of FePt films with near equiatomic composition was studied. Whereas flash lamp annealed FePt films exhibit a polycrystalline morphology with high chemical L10 order, rapid thermal annealing can lead to the formation of chemically ordered FePt fifilms with (001) texture on amorphous SiO2/Si substrates. The resultant high perpendicular magnetic anisotropy and large coercivities up to 40 kOe are demonstrated. Simultaneuosly to the ordering transformation, rapid thermal annealing to temperatures exceeding 600 °C leads to a break up of the continuous FePt film into separated islands. This dewetting behavior was utilized to create regular arrays of FePt nanostructures on SiO2 particle templates with periods down to 50 nm. The addition of Cu improves the (001) texture formation and chemcial ordering for annealing temperatures T < 600 °C. In addition, the magnetic anisotropy and the coercivity of the ternary FePtCu alloy can be effectively tailored by adjusting the Cu content. The prospects of FePtCu based exchange spring media, as well as the magnetic properties of FePtCu nanostructures fabricated using e-beam and nanoimprint lithography have been investigated.