Dissertations / Theses on the topic 'Charge Pump PLL'

碩士<br>中原大學<br>電子工程研究所<br>103<br>In this paper, we design a PLL for low voltage differential signal(LVDS) serializer/deserializer. We can reduce the area of chip by using charge pump and ring oscillator. Design platform is 0.18μm 1P6M CMOS process. The output frequency is 840MHz at 120MHz input frequency. The power is 5.24mW at 1.8V power supply, setting time is 12μs and jitter is 4.2ps.

碩士<br>朝陽科技大學<br>資訊工程系碩士班<br>92<br>ABSTRACT Phase-Locked Loop (PLL) is very popular and important in the applications of Integrated circuit field. Examples of the applications that use PLL include clock and data recovery, clock synthesis or synchronization, frequency synthesis, and PLL modulator or de-modulator applications. The basic operating principle of PLL is to synchronize an output signal with a reference or input signal in frequency as well as phase. When the phase error between the oscillator’s output signal and the reference signal is zero, or remains constant that often called locked-stated, the condition of fast-locked is become more and more important in PLL design. In this thesis, we propose a dual-loop phase locked loop architecture which can effectively reduce the locked-time. The simulation and analysis of dual-loop phase locked loop was accomplished by using the TSMC 0.35 2P4M CMOS process. When input frequency is equal to 880 MHz in simulation, the locked time of dual-loop is 1.8 and single loop is 8.6 . Therefore, the dual-loop PLL can provide for fast locked demand.

Phase Locked Loop (PLL) is an integral component of clock generation circuits. A third order Charge Pump PLL (CPPLL) is most widely employed PLL architecture due to its zero steady state phase error. A monolithic implementation of such a CPPLL presents numerous challenges to PLL designers, the number of such challenges vary depending on the process technology employed and the end application. One such challenge that is worth mentioning is the on-chip integration of the second order passive loop filter. The area occupied by the second order passive loop filter is mainly determined by the zero determining capacitance (CZ). A low loop bandwidth CPPLL has a higher CZ value, and hence consumes a larger die area than a large loop bandwidth CPPLL. Literature survey shows that the problem of higher CZ value in low loop bandwidth CPPLL is addressed by using some form of emulation techniques. A relatively simpler emulation technique is the use of dual charge pump based loop filter. Existing dual charge pump based loop filter consume extra elements (such as summer that need opamps to realize the summer function) for achieving low CZ value. These extra elements consume extra area and additional power. We present two types of Summer-Less Dual Charge Pump (SDCP) based loop filter designs that do not need extra elements and still achieves low CZ value and this is achieved by using a second charge pump in an appropriate way. A test chip was implemented in 0.13µm UMC MMRFCMOS process to verify the presented circuits. The presented SDCP based loop filter circuits are particularly useful in designs employing multiple CPPLL’s and design employing low loop bandwidth CPPLL’s. Another challenge worth-mentioning is the frequency ranges over which the PLL can be locked. The Voltage Controlled Oscillator (VCO) of PLL mainly determines the frequency locking range of a PLL. A typical VCO has a frequency locking range of usually 1:2 to 1:3. The VCO frequency tuning range reduces with reduction in supply voltage. This poses a serious problem in low supply voltage applications that demand a wide frequency locking range, sometimes greater than 1:3. We have addressed this problem of wide PLL lock range, by using an Analog Frequency Detector. A wide frequency lock range is achieved, either by dynamically modifying the VCO or the feedback divider of PLL. Both the approaches are equally feasible. The frequency detector is used for dynamically modifying the VCO or the feedback divider of PLL. Two test chips were implemented to verify the presented Analog Frequency Detector scheme. A testchip implemented in 0.25µm CSM analog process achieves wide frequency lock range by dynamically modifying the feedback divider of PLL. Another testchip implemented in 0.13µm UMC MMRFCMOS process achieves wide frequency lock range by dynamically modifying the center frequency of the VCO. Presented analog frequency detection scheme is particularly useful in applications that demand wide PLL lock range from a single die.

Phase Locked Loop (PLL) is an integral component of clock generation circuits. A third order Charge Pump PLL (CPPLL) is most widely employed PLL architecture due to its zero steady state phase error. A monolithic implementation of such a CPPLL presents numerous challenges to PLL designers, the number of such challenges vary depending on the process technology employed and the end application. One such challenge that is worth mentioning is the on-chip integration of the second order passive loop filter. The area occupied by the second order passive loop filter is mainly determined by the zero determining capacitance (CZ). A low loop bandwidth CPPLL has a higher CZ value, and hence consumes a larger die area than a large loop bandwidth CPPLL. Literature survey shows that the problem of higher CZ value in low loop bandwidth CPPLL is addressed by using some form of emulation techniques. A relatively simpler emulation technique is the use of dual charge pump based loop filter. Existing dual charge pump based loop filter consume extra elements (such as summer that need opamps to realize the summer function) for achieving low CZ value. These extra elements consume extra area and additional power. We present two types of Summer-Less Dual Charge Pump (SDCP) based loop filter designs that do not need extra elements and still achieves low CZ value and this is achieved by using a second charge pump in an appropriate way. A test chip was implemented in 0.13µm UMC MMRFCMOS process to verify the presented circuits. The presented SDCP based loop filter circuits are particularly useful in designs employing multiple CPPLL’s and design employing low loop bandwidth CPPLL’s. Another challenge worth-mentioning is the frequency ranges over which the PLL can be locked. The Voltage Controlled Oscillator (VCO) of PLL mainly determines the frequency locking range of a PLL. A typical VCO has a frequency locking range of usually 1:2 to 1:3. The VCO frequency tuning range reduces with reduction in supply voltage. This poses a serious problem in low supply voltage applications that demand a wide frequency locking range, sometimes greater than 1:3. We have addressed this problem of wide PLL lock range, by using an Analog Frequency Detector. A wide frequency lock range is achieved, either by dynamically modifying the VCO or the feedback divider of PLL. Both the approaches are equally feasible. The frequency detector is used for dynamically modifying the VCO or the feedback divider of PLL. Two test chips were implemented to verify the presented Analog Frequency Detector scheme. A testchip implemented in 0.25µm CSM analog process achieves wide frequency lock range by dynamically modifying the feedback divider of PLL. Another testchip implemented in 0.13µm UMC MMRFCMOS process achieves wide frequency lock range by dynamically modifying the center frequency of the VCO. Presented analog frequency detection scheme is particularly useful in applications that demand wide PLL lock range from a single die.

碩士<br>中華大學<br>電機工程學系碩士班<br>94<br>In the design of phase-locked loop (PLL), the most important consideration is the steady and reliable frequency. When we change the input frequency, the PLL will go to be in lock at the least time. So, we will design of the how to reduce the locking time of the PLL, and have a biggest locking range, very low frequency skew, low phase error and low power consumption. In this thesis, we will present a novel PLL, which consists of the proposed phase frequency detector (PFD), a charge pump (CP), the voltage-controlled tuning loop (VCTL), a V-I circuit, a voltage controlled oscillator (VCO), and a frequency divider (FD). We utilize this new structure of PLL to achieve fast locking and low frequency skew. We use Hspice in circuit simulation. We use Cadance tools to proceed layout, and use LVS to compare circuit and layout, and extract the capacitance and do Post- simulation to approach the operation of a true chip. Finally, the simulation results show that the locking time of PLL is 2.65us, phase error is 43ps, frequency skew is 900MHz 1KHz and VCO linearly gain is 661MHz/V. The power consumption is 14.1mW when PLL operates at 900MHz , the whole chip area including PAD is 730 691 um2.

In modern transceivers, a low power PLL is a key block. It is known that with the evolution of technology, lower power and high performance circuitry is a challenging demand. In this thesis, a low power PLL is developed in order not to exceed 2mW of total power consumption. It is composed by small area blocks which is one of the main demands. The blocks that compose the PLL are widely abridged and the final solution is shown, showing why it is employed. The VCO block is a Current-Starved Ring Oscillator with a frequency range from 400MHz to 1.5GHz, with a 300μW to approximately 660μW power consumption. The divider is composed by six TSPC D Flip-Flop in series, forming a divide-by-64 divider. The Phase-Detector is a Dual D Flip-Flop detector with a charge pump. The PLL has less than a 2us lock time and presents a output oscillation of 1GHz, as expected. It also has a total power consumption of 1.3mW, therefore fulfilling all the specifications. The main contributions of this thesis are that this PLL can be applied in ISM applications due to its covering frequency range and low cost 130nm CMOS technology.

With decreasing feature sizes, lowered supply voltages and increasing operating frequencies, the radiation tolerance of digital circuits is becoming an increasingly important problem. Many radiation hardening techniques have been presented in the literature for combinational as well as sequential logic. However, the radiation tolerance of clock generation circuitry has received scant attention to date. Recently, it has been shown that in the deep submicron regime, the clock network contributes significantly to the chip level Soft Error Rate (SER). The on-chip Phase Locked Loop (PLL) is particularly vulnerable to radiation strikes. In this thesis, we present a radiation hardened PLL design. Each of the components of this design-the voltage controlled oscillator (VCO), the phase frequency detector (PFD) and the charge pump/loop filter-are designed in a radiation tolerant manner. Whenever possible, the circuit elements used in our PLL exploit the fact that if a gate is implemented using only PMOS (NMOS) transistors then a radiation particle strike can result only in a logic 0 to 1 (1 to 0) flip. By separating the PMOS and NMOS devices, and splitting the gate output into two signals, extreme high levels of radiation tolerance are obtained. Our design uses two VCOs (with cross-coupled inverters) and charge pumps, so that a strike on any one is compensated by the other. Our PLL is tested for radiation immunity for critical charge values up to 250fC. Our SPICE-based results demonstrate that after exhaustively striking all circuit nodes, the worst case jitter of our hardened PLL is just 37.4 percent. In the worst case, our PLL returns to the locked state in 2 cycles of the VCO clock, after a radiation strike. These numbers are significant improvements over those of the best previously reported approaches.

There has been a huge rise in interest in the design of energy efficient wireless sensor networks (WSN) and body area networks (BAN) with the advent of many new applications over the last few decades. The number of sensor nodes in these applications has also increased tremendously in the order of few hundreds in recent years. A typical sensor node in a WSN consists of circuits like RF transceivers, micro-controllers or DSP, ADCs, sensors, and power supply circuits. The RF transmitter and receiver circuits mainly the frequency synthesizers(synthesis of RF carrier and local oscillator signals in transceivers) consume a significant percentage of its total power due to its high frequency of operation. A charge-pump phase locked loop (CP-PLL) is the most commonly used frequency synthesizer architecture in these applications. The growing demands of WSN applications, such as low power consumption larger number of sensor nodes, single chip solution, and longer duration operation presents several design challenges for these transmitter and frequency synthesizer circuits in these applications and a few are listed below, Low power frequency synthesizer and transmitter designs with better spectral performance is essential for an energy efficient operation of these applications. The spurious tones in the frequency synthesizer output will mix the interference signals from nearby sensor nodes and from other interference sources present nearby ,to degrade the wireless transmitter and receiver performance[1]. With the increased density of sensor nodes (more number of in-band interference sources) and degraded performance of analog circuits in the nano-meter CMOS process technologies, the spur reduction techniques are essential to improve the performance of frequency synthesizers in these applications. A single chip solution of sensor nodes with its analog and digital circuits integrated on the same die is preferred for its low power, low cost, and reduced size implementation. However, the parasitic interactions between these analog and digital sub-systems integrated on a common substrate, degrade the spectral performance of frequency synthesizers in these implementations[2]. Therefore, techniques to improve the mixed signal integration performance of these circuits are in great demand. In this thesis, we present a custom designed energy efficient 2.4 GHz BFSK/ASK transmitter architecture using a low power frequency synthesizer design technique taking advantage of the CMOS technology scaling benefits. Furthermore, a few design guidelinesandsolutionstoimprovethespectralperformanceoffrequency synthesizer circuits and in-turn the performance of transmitters are also presented. The target application being short distance, low power, and battery operated wireless communication applications. The contributions in this thesis are, Spectral performance improvement techniques The CP mismatch current is a dominant source of reference spurs in the nano-meter CMOS PLL implementations due to its worsened channel length modulation effect [3]. In this work, we present a CP mismatch current calibration technique using an adaptive body bias tuning of its PMOS transistors. Chip prototype of 2.4 GHzCP-PLLwith the proposed CP calibration technique was fabricated in UMC 0.13 µm CMOS process. Measurements show a CP mismatch current of less than 0.3 µA(0.55 %) using the proposed calibration technique over the VCO control voltage range 0.3 to 1 V. The closed loop PLL measurements using the proposed technique exhibited a 9dB reduction in the reference spur levels across the PLL output frequency range 2.4 -2.5 GHz. The parasitic interactions between analog and digital circuits through the common substrate severely affects the performance of CP-PLLs. In this work, we experimentally demonstrate the effect of periodic switching noise generated from the digital buffers on the performance of charge-pump PLLs. The sensitivity of PLL performance metrics such as output spur level, phase noise, and output jitter are monitored against the variations in the properties of a noise injector digital signal. Measurements from a 500 MHz CP-PLL shows that the pulsed noise injection with the duty cycle of noise injector signal reduced from 50% to 20%, resulted in a 12.53 dB reduction in its output spur level and a 107 ps reduction in its Pk-Pk deterministic period jitter performance. Low power circuit techniques A low power frequency synthesizer design using a digital frequency multiplication technique is presented. The proposed frequency multiply by 3 digital edge combiner design having a very few logic gates, demonstrated a significant reduction in the power consumption of frequency synthesizer circuits, with an acceptable spectral performance suitable for these relaxed performance applications. A few design guidelines and techniques to further improve its spectral performance are also discussed and validated through simulations. Chip prototypes of 2.4 GHz CP-PLLs with and without digital frequency multiplier circuits are fabricated in UMC 0.13 µm CMOS process. The 2.4 GHz CP-PLL using the proposed digital frequency multiplication technique (10.7 mW) consumed a much reduced power compared to a conventional implementation(20.3 mW). A custom designed, energy efficient 2.4 GHz BFSK/ASK transmitter architecture using the proposed low power frequency synthesizer design technique is presented. The transmitter uses a class-D power amplifier to drive the 50Ω antenna load. Spur reduction techniques in frequency synthesizers are also used to improve the spectral performance of the transmitter. A chip prototype of the proposed transmitter architecture was implemented in UMC0.13 µm CMOS process. The transmitter consume14 mA current from a 1.3V supply voltage and achieve improved energy efficiencies of 0.91 nJ/bit and 6.1 nJ/bit for ASK and BFSK modulations with data rates 20Mb/s & 3Mb/s respectively.

There has been a huge rise in interest in the design of energy efficient wireless sensor networks (WSN) and body area networks (BAN) with the advent of many new applications over the last few decades. The number of sensor nodes in these applications has also increased tremendously in the order of few hundreds in recent years. A typical sensor node in a WSN consists of circuits like RF transceivers, micro-controllers or DSP, ADCs, sensors, and power supply circuits. The RF transmitter and receiver circuits mainly the frequency synthesizers(synthesis of RF carrier and local oscillator signals in transceivers) consume a significant percentage of its total power due to its high frequency of operation. A charge-pump phase locked loop (CP-PLL) is the most commonly used frequency synthesizer architecture in these applications. The growing demands of WSN applications, such as low power consumption larger number of sensor nodes, single chip solution, and longer duration operation presents several design challenges for these transmitter and frequency synthesizer circuits in these applications and a few are listed below, Low power frequency synthesizer and transmitter designs with better spectral performance is essential for an energy efficient operation of these applications. The spurious tones in the frequency synthesizer output will mix the interference signals from nearby sensor nodes and from other interference sources present nearby ,to degrade the wireless transmitter and receiver performance[1]. With the increased density of sensor nodes (more number of in-band interference sources) and degraded performance of analog circuits in the nano-meter CMOS process technologies, the spur reduction techniques are essential to improve the performance of frequency synthesizers in these applications. A single chip solution of sensor nodes with its analog and digital circuits integrated on the same die is preferred for its low power, low cost, and reduced size implementation. However, the parasitic interactions between these analog and digital sub-systems integrated on a common substrate, degrade the spectral performance of frequency synthesizers in these implementations[2]. Therefore, techniques to improve the mixed signal integration performance of these circuits are in great demand. In this thesis, we present a custom designed energy efficient 2.4 GHz BFSK/ASK transmitter architecture using a low power frequency synthesizer design technique taking advantage of the CMOS technology scaling benefits. Furthermore, a few design guidelinesandsolutionstoimprovethespectralperformanceoffrequency synthesizer circuits and in-turn the performance of transmitters are also presented. The target application being short distance, low power, and battery operated wireless communication applications. The contributions in this thesis are, Spectral performance improvement techniques The CP mismatch current is a dominant source of reference spurs in the nano-meter CMOS PLL implementations due to its worsened channel length modulation effect [3]. In this work, we present a CP mismatch current calibration technique using an adaptive body bias tuning of its PMOS transistors. Chip prototype of 2.4 GHzCP-PLLwith the proposed CP calibration technique was fabricated in UMC 0.13 µm CMOS process. Measurements show a CP mismatch current of less than 0.3 µA(0.55 %) using the proposed calibration technique over the VCO control voltage range 0.3 to 1 V. The closed loop PLL measurements using the proposed technique exhibited a 9dB reduction in the reference spur levels across the PLL output frequency range 2.4 -2.5 GHz. The parasitic interactions between analog and digital circuits through the common substrate severely affects the performance of CP-PLLs. In this work, we experimentally demonstrate the effect of periodic switching noise generated from the digital buffers on the performance of charge-pump PLLs. The sensitivity of PLL performance metrics such as output spur level, phase noise, and output jitter are monitored against the variations in the properties of a noise injector digital signal. Measurements from a 500 MHz CP-PLL shows that the pulsed noise injection with the duty cycle of noise injector signal reduced from 50% to 20%, resulted in a 12.53 dB reduction in its output spur level and a 107 ps reduction in its Pk-Pk deterministic period jitter performance. Low power circuit techniques A low power frequency synthesizer design using a digital frequency multiplication technique is presented. The proposed frequency multiply by 3 digital edge combiner design having a very few logic gates, demonstrated a significant reduction in the power consumption of frequency synthesizer circuits, with an acceptable spectral performance suitable for these relaxed performance applications. A few design guidelines and techniques to further improve its spectral performance are also discussed and validated through simulations. Chip prototypes of 2.4 GHz CP-PLLs with and without digital frequency multiplier circuits are fabricated in UMC 0.13 µm CMOS process. The 2.4 GHz CP-PLL using the proposed digital frequency multiplication technique (10.7 mW) consumed a much reduced power compared to a conventional implementation(20.3 mW). A custom designed, energy efficient 2.4 GHz BFSK/ASK transmitter architecture using the proposed low power frequency synthesizer design technique is presented. The transmitter uses a class-D power amplifier to drive the 50Ω antenna load. Spur reduction techniques in frequency synthesizers are also used to improve the spectral performance of the transmitter. A chip prototype of the proposed transmitter architecture was implemented in UMC0.13 µm CMOS process. The transmitter consume14 mA current from a 1.3V supply voltage and achieve improved energy efficiencies of 0.91 nJ/bit and 6.1 nJ/bit for ASK and BFSK modulations with data rates 20Mb/s & 3Mb/s respectively.

博士<br>國立臺灣大學<br>電子工程學研究所<br>101<br>This thesis presents a 0.18-μm and a 90-nm CMOS wideband phase-locked loops with low reference spurs. A charge-pump current calibration technique is proposed to maintain a constant loop bandwidth for wide operation frequency range and achieve low reference spurs. First level charge-pump current calibration is seamlessly incorporated in the automatic frequency band hopping control and the mechanism also ensures enough negative transconductance for the voltage-controlled oscillator to function throughout the whole frequency range. The charge-pump mismatch is calibrated by second level charge-pump current calibration combined with a pulse-width scaling technique. The proposed CMOS 0.18-μm PLL operation frequency range covers from 4.7 GHz to 6.1GHz. The measured phase noise is -116 dBc/Hz at 1MHz offset and the reference spur is -68.5 dBc. The proposed CMOS 90-nm PLL operates form 39.5-47.1GHz. The reference spur is below -57.6dB. The measured phase noise is -92.35dBc/Hz at 1MHz offset.

碩士<br>國立中央大學<br>電機工程研究所<br>97<br>Along with the evolution of manufacturing process, the size of integrated circuits has shrunk into the nanometer scale. Process variation and yield loss issues became more and more serious, especially for analog circuits. Therefore, the design-for-manufacturability (DFM) and design-for-yield (DFY) techniques have been widely used to reduce the impacts of those negative effects. If designers can consider the process variation phenomena in early design stages, the design iterations could be shortened significantly to achieve better economical benefit. In this thesis, we propose a sizing flow for the phase-locked loop circuits with a charge pump to reduce the process sensitivity. Using the hierarchical concept, the geometrical parameters of the sensitivity analog blocks are adjusted for sensitivity reduction with similar nominal performance, the yield of PLL is improved significantly after sensitivity reduction as shown in the experimental results.

博士<br>華梵大學<br>機電工程研究所<br>95<br>This dissertation contains two parts. One is the analysis of noise performance of charge-pump phase- locked loops (CPPLLs) under continuous-time models. The other is the stability analysis of CPPLLs using discrete-time models. In the first part, we derive the upper bound of the phase-jitter variance of second-order and third-order CPPLLs. We employ the simple linear model in the beginning and integrate the power spectral density functions from different noise sources to determine the closed form for an upper bound of the phase-jitter variance. The noise sources we have considered in this paper are the phase noise from the voltage controlled oscillator (VCO), the noise from the charge pump, the noise from the loop filter, and the noise in the reference clock. Some experiments are performed to verify the proposed theory. The curves of the theoretical upper bounds possess similar shapes with the experimental results. In the second part, we derive state equations for linearized discrete-time models of CPPLLs from second-order loops to forth-order loops. We solve the differential equations of the loop filter by using the initial conditions and the boundary conditions in a period. The solved equations are linearized and rearranged as discrete-time state equations for checking stability conditions and overload conditions. Some behavioral simulations are performed to verify the proposed method. By examining the stability of loops with different conditions, we also propose an expression between the lower bound of the reference frequency, the open loop unit gain bandwidth, and the phase margin. We hope that the analysis above is helpful to the engineers for designing charge-pump phase- locked loops.