Dissertations / Theses on the topic 'Clay mineralogy'

Currently, there is very little research available on nonpoint source pollution from rural watersheds. Government regulatory agencies are desperate for information regarding the causes of nonpoint source pollution, which includes the relationship between suspended soil particles and dispersion. Since soil dispersion is dependent on clay mineralogy, knowing the clay mineralogy of the soil in an area can help predict sediment loads entering the surrounding surface waters. This information is necessary to protect the resource value of our rivers, lakes, and estuaries, as well as to protect recreational activities such as fishing or hunting; but most importantly, this information is necessary to ensure the safety of our drinking water supply. Clay mineralogy and its influence on dispersion, as well as dispersion and its relation to water quality are the focus of this study. Soil mineralogy affects water quality in several ways: soil mineralogy determines the dispersivity of the clay portion of the soil and dispersive clays are likely to end up as suspended sediment in surface waters; weathering reactions contribute elements to water as dissolved load, and the sorption properties of clay minerals contribute to soils' ability to filter and carry pollutants. Through the use of X-ray diffraction, dispersivity, atomic absorption spectrometry, cation exchange capacity, and petrographic microscopy, this study shows that the clay mineral fraction of a soil determines the dispersivity, and that dispersed clay minerals contribute excess nutrients and metals as nonpoint source pollutants to surface waters.

The clay mineral composition of sediments deposited in the last six oxygen isotope stages in the Gulf of Mexico continental slope was characterized. Smectite and illite were found to be the two major clay minerals of the clay fraction while kaolinite, chlorite and quartz were present in the clay fraction but in less proportions. Variations in clay mineral abundances, especially in the relative abundances of smectite and illite, were identified in relation to climate changes. Smectite was the most abundant mineral in sediments of the current (stage 1) and last interglacial maxima (stage 5) while illite dominates the clay min-eralogy of sediments from the last glacial maximum (stage 2). Relationships between clay mineralogy and physical properties were investigated as well. Significant positive correla-tions were found between Atterberg limits with the smectite content of the bulk sediment and with clay content. However, the relationship with smectite yielded a significantly higher correlation coefficient. Smectite and clay content also affect the natural water con-tent of sediments and its changes with depth.

This research has evaluated the engineering behaviour of the tropical clay soils of Dhaka, Bangladesh. Attempts have been made to show the relationship of mineralogy and fabric with engineering properties. The engineering behaviour has been investigated by comparing the soil properties in a natural and destructured state at the same void ratio. Consolidation behaviour of the soils are discussed, based on oedometer and triaxial tests. Undrained and drained mechanical behaviour have been evaluated from triaxial tests in terms of stress-strain curves, stress paths, bonding effects, critical state conditions, stiffness and yielding behaviour. A framework for the tropical clay soils of Dhaka is presented. The tropical clay soils of Dhaka are intermediate to high plasticity inorganic clay. These soils are mainly composed of illite,. kaolinite, chlorite and some non clay minerals mainly quartz and feldspar. It was observed that these sods showed a random open microfabric of silt and clay. There was also some evidence that aluminosilicates, iron compounds and silica formed bonds between and within the grains. An apparent preconsolidation pressure of 170 kPa to 250 kPa was estimated for the natural soils, which is likely to be due to the bonded structure of the soils. The compressibility of the soil is very low to medium. The consolidation results are consistent with the mineralogy of the soils. It is established that the tropical clay soils of Dhaka are bonded. Bonding has an influence on the development of stress-strain and stiffness of these soils. Under undrained shearing, samples initially showed peak positive values of excess pore water pressure followed by negative values at higher strains due to the tendency of the samples to dilate. No negative pore water pressures were observed at high confining pressures. Only a few samples at low confining pressures reach the critical state at very large strains approximately in excess of 20%. High confining pressure samples may not have reached the critical state due to the formation of distinct shear surfaces. A significant difference between the natural and destructured failure surfaces was observed due to the presence of bonds in the natural soils. Differences in failure type were observed between the natural and destructured soils of three boreholes. It was observed that stiffness values gradually decreased with increasing strain. For the natural soils, two yield points could be identified at low confining pressures below the final yield. It was also observed that bond breakdown would occur in isotropic compression for tests at high confining pressures. At the final yield, the soil looses almost all of its stiffness due to bonding. After final yield, a soil’s behaviour is controlled only by friction. It was observed that three zones of behaviour could be identified for these soils in the stress space.

Yes<br>This paper examines the impacts of clay mineralogy on the effectiveness of lime stabilisation at different temperatures. A comprehensive experimental programme was conducted to track down the evolution of lime-clay reactions and their durations through monitoring the evolution of strength gain at predetermined times using the Unconfined Compressive Strength (UCS) test. The study examined clays with different mineralogy compositions comprising Na+ Bentonite and Ball (Kaolinite) clay. Four different clays were tested including 100% bentonite, 100% Ball clay and two clay mixtures with ratios of 1:1 and 1:3 by mass of bentonite to Ball clay. All clays were treated using a range of lime content up to 25% and cured for a period of time up to 672 h at two different temperatures of 20 and 40 °C. The results showed that the continuity of the fast phase (stage 1) of strength gain was dependent on the availability of lime in particular at the higher temperature. Whereas, for the same lime content, the duration of the fast phase and the kinetic of strength gain were significantly related to the clay mineralogy and curing temperature. Except for the initial strength gain at 0 h curing time, the lime-treated Ball clay specimens at 20 °C appeared to show no strength gain throughout the curing period that extended up to 672 h. However, when curing occurred at 40 °C, the no strength gain stage only lasted for 72 h after which a gradual increase in the strength was observed over the remaining curing period of time. The addition of Bentonite to Ball clay succeeded in kicking off the strength gain after a short period of curing time at both curing temperatures.

The Yazoo Clay is a calcareous fossiliferous mudrock that outcrops in a northwest-southeast belt across much of Mississippi and in adjacent states. Based on over 240 X-ray diffraction analyses, the average composition of the Yazoo Clay is 28% smectite, 24% kaolinite, 22% quartz, 15% calcite, 8% illite, 2% feldspar, and 1% gypsum. Exposed Yazoo clay is weathered to a depth of 30-40 ft. and has a distinctive yellow/brown color; unweathered Yazoo is blue/gray. In most wells, smectite is more abundant in weathered clay than in unweathered clay. Mineralogic changes correlate well with engineering properties of the samples, which in general show a decrease in plasticity indices with depth. Weathered Yazoo clay exhibits greater mineralogic variability than unweathered clay. Mineralogical content also varies laterally. Lateral variation, along with correlative smectite content and engineering properties, is the reason for ?roller coaster? roadways and structural damage caused by the swelling Yazoo Clay.

Thesis (Ph. D.)--University of Oregon, 2000.<br>Typescript. Includes vita and abstract. Includes bibliographical references (leaves 169-178). Also available for download via the World Wide Web; free to University of Oregon users.

This thesis is concerned with the current contentious issue of environmental containment. This work provides an assessment of contaminant migration through Geosynthetic Clay Liners (GCLs). GCLs are thin liners usually consisting of three layers, defined in section 2.2.4. These are factory manufactured materials, used extensively in the waterproofing and environmental containment markets. The predominant, if not the only "low flow" element in GCLs is bentonite, described in section 2.4.1. Bentonite has been found to be most advantageous as the waterproofing core of GCLs. During this research, emphasis was placed on an investigation as to the nature of the low flow core of the GCLs in terms of mineralogy and microstructure. GCL types can be divided into two generic categories; granulated/powdered and extruded (pre-hydrated). One of each of the generic types were selected for this study to provide a representative overview of the GCL product range. The main type of laboratory assessment was that of fluid migration through the liners. Due to the paucity of knowledge in relation to diffusion, emphasis was put on diffusion assessment. At an early stage in this research, it was found that suitable equipment for the assessment of diffusion was not available and, as a result the author developed two main types of diffusion test cells which were key to this work. These cells were the constant stress and constant volume diffusion cells. In the author's opinion, the constant stress cell, in particular, offers many advantages over current diffusion equipment. During the production of these cells, emphasis was placed on the following factors; sample size, control of effective stress, mixing of fluid, reduction in sample and fluid contamination, reservoir size, sample boundary, reduction of leaks and ease of sampling. Following the development of the diffusion cells, extensive testing was carried out. Using solutions of sodium, potassium and calcium chloride the assessment of contaminants was selectively limited. A concentration gradient was created across the GCL sample by placing a cation solution on one side and deionised water on the other. Following hydration of the GCL samples with deionised water, 1000ppm of prepared solution was placed in the source reservoir whilst fresh deionised water was placed in the receptor reservoir. Samples were taken at regular intervals, from both source and receptor reservoirs, and their concentrations assessed. Profiles of source and receptor concentrations were plotted versus time. A tabulated Microsoft Excel spread sheet was used in the determination of diffusion coefficient. This was achieved by incorporating equations from the concentration plots with Ficks' law. Extensive hydraulic conductivity tests carried out by the author on the GCLs were compared with the diffusion tests. Standard triaxial, Rowe & large column hydraulic conductivity tests were produced. A large part of the investigation was the assessment of the characteristics of the waterproofing core of the GCLs. A number of techniques were adopted for this assessment. These included the following; X-ray Diffraction (XRD), X-Ray Fluorescence (XRF) & Scanning Electron Microscope Analysis (SEM). These assessments provided an overview as to the characteristics of the bentonite core. The SEM, in particular, was used to assess the microstructure of the two types of GCL under investigation and was used to determine if there was any variance in the particle frequency, type, shape and orientation. The XRF and XRD equipment were used to make an assessment of the mineralogy of the bentonite core. These procedures were conducted on a number of available bentonite granules and assessed relative to that of the core product of the GCL under investigation. Tests were also conducted on samples used in the diffusion experiments. Sections of the samples were removed from the source, middle and receptor sides of the samples and taken for analysis. The discussion and concluding remarks of this thesis have highlighted a number of key findings. It was noted that there is a marked difference between the granulated and extruded (pre-hydrated) GCLs assessed. It was found that the extruded (pre-hydrated) GCL exhibits an orientated microstructure. The bentonite particles were predominantly orientated flat across the width of the GCL. The granulated bentonite, when hydrated, did not exhibit any preferential orientation of bentonite particles.

Unconformity-related uranium deposits in the Athabasca Basin represent a significant global resource of uranium. One such deposit, the Phoenix Deposit, discovered in 2007 on Denison Mine’s Wheeler River property, shares similarities with other deposits in the Basin. The Phoenix Deposit is located at the apex between a basement shear structure, and the unconformity between the crystalline basement and overlying sandstones. The shear structure extends into the sandstones, this structure controls the distribution of alteration minerals in the basement and early alteration phases in sandstones. The shear structure extending to sandstones is not spatially associated with late alteration phases associated with the uranium deposit, suggesting that the structure was not important for uranium mineralisation. Bulk rock compositions of sandstones show chimney-like distribution of elements above the uranium deposit. The most notable ones are the distribution of yttrium, and boron. Rare earth elements and yttrium are not soluble in aqueous fluids at low temperatures and they are enriched in uranium ore. Therefore, the chimney-like distribution of elements are attributed to uraniferous hydrothermal activity in sandstones. Petrographic and chemical analysis of alteration associated with the Phoenix Deposit shows two types of tourmaline, a pre-ore (Tur 1) in the basement, which is likely a metamorphic product (Tur1) and a syn-ore magnesiofoitite (Tur 2) in the basement and the sandstones. Three generations of chlorite are identified within the alteration halo of the Phoenix Deposit; an early Fe-rich clinochlore (C1) in the basement and sandstones, the second generation, Mg-rich sudoitic chlorite (C2) in the basement, and a late, sudoitic chlorite (C3) in the basement and sandstones. Illite shows three types; an early and late M1 and a late M2. M1 is found as two polytypes, 1Mc and 1Mt, in the basement and sandstones, with the 1Mt having a spatial relationship with the uranium deposit. Late M2 illite is coarse-grained and occurs in the basement and sandstones. Near Infrared (NIR) spectra of sandstones overlying the deposit shows absorption features between 600 and 700 nm. It is considered that these absorption features appear to have been produced during late hydrothermal activity and may have a temporal as well as spatial relationship with uranium mineralisation.

Abstract The mineralogy and geochemistry of the fine and clay fractions of till in different moraine types and in different bedrock areas in northern Finland have been studied. A total of 250 till samples from 140 test pits were studied mineralogically and geochemically. X-ray diffraction, differential thermal and thermogravimetric analyses, transmission electron microscopy, X-ray fluorescence and atomic absorption spectrometry were used as analytical methods. In the clay fraction of till quartz, plagioclase, microcline and amphibole are the primary minerals occurring. The clay minerals proper include vermiculite, chlorite, illite, swelling-lattice vermiculite and mixed-layer clay minerals. Kaolinite occurs most abundantly in the clay fractions of till in the Kittilä, Jerisjärvi, Kaaresuvanto and Pulju areas. In the clay fraction of Kittilä and Jerisjärvi illite is dioctahedral type, but in their of other study areas both di- and trioctahedral types occur. Kaolinite and dioctahedral illite are evidence of the mixing of the weathered bedrock material into the till matrix. In the fine fraction of till most abundant minerals are primary minerals and clayminerals are in a minor role. In the clay fraction of till the content of primary minerals are at higher and secondary minerals are at lower level in the Granitic and Archaean gneiss areas than in the Greenstone Belt, Svecokarelian schists and gneiss and Granulite areas. Amphibole, microcline and plagioclase occur in very low amounts or are totally destroyed by chemical weathering in the clay fraction of the till in the Kittilä area. The mineral composition of fine and clay fractions in the tills of northern Inari gives an indication that there occur much more mafic volcanites than is known today. The mineralogical compositions of fine fraction of the tills correlates quite well with the underlying bedrock in all study areas, but clay fraction does not. Geochemical results are in accordance with the mineralogical composition of both fractions. In the fine fraction of the till Si, Ca and Na contents are higher than in the clay fraction. Clay fraction is enriched in Al, Fe, Mg, K and trace elements as compared to the fine fraction. Present study material points out that the distribution of chemical elements in the clay fraction of the till does not correlate with the composition of the underlying bedrock, but fine fraction does so with a few exceptions. The chemical composition of till in Kaaresuvanto and Inari does not fully correspond to the composition of the underlying bedrock as known today. In northern Inari and Kittilä the results give an indication that there are more mafic volcanites and/or sulphide mineralizations occurring in these areas than is known at the present time. The most important factors controlling the mineralogical and geochemical composition of the fine and clay fractions of the tills in northern Finland are the composition of the bedrock and the possible occurrence of an old weathering crust. The final grain size composition of the tills and consequently the quantitative proportions of the different minerals are often related to the last glacial quarrying and sorting processes; therefore the mineralogical composition of the tills is to a certain extent bound also to the respective moraine type.

Hypersaline tidal flats (HTFs) are transitional ecosystems commonly occurring in arid and semiarid coastal areas. (e.g. Australia and New Caledonia), Africa (e.g. Senegal, Gambia, and Madagascar), Central America (e.g. Nicaragua), South America (e.g. Ecuador and on the north, northeast, and southeast Brazilian coasts). Due to their location, HTFs might exert biogeochemical control over cycling of nutrients (e.g. Fe and Si) across the land to ocean transition, accelerating or retarding the nutrient export to the ocean and other adjacent ecosystems. This biogeochemical control is governed by soil physicochemical conditions (e.g. pH and salinity) and pedogenesis (e.g. redox processes). Thus, study of the soil coloidal fraction, the pedogenic processes, and the distribution of Si in the different soil components can provide a detailed characterization of HTF soils and give insights into the Si dynamics in these environments. In view of this, two HTFs on the Brazilian coast were studied on the Brazilian coast and the data are presented here. The first chapter aims to investigate the pedogenesis in HTF soils based on detailed morphological descriptions and Fe and Mn sequential extractions. The second chapter discusses silicon geochemistry in HTF soils based on sequential extractions, SEM, and XRD modeling of the fine clay fraction. And lastly, the third one reports the characteristics, distribution, and genesis of clay minerals in HTF soils on the basis of XRD modeling, TEM-EDS, FTIR, and XRF analysis. Redox reactions control the pedogenic evolution in HTF soils. These processes lead to a mobilization of Fe2+ and Mn2+ upward in the soils profiles, followed by oxidation and precipitation of Fe and Mn oxyhydroxides. These reactions, along with pyrite oxidation, lead to a transformation of the deeper soil horizons. Formation of Fe oxyhydroxides in the uppermost soil horizons exerts control on Si dynamics by co-precipitation and adsorption reactions. Together, Si associated with Fe oxyhydroxides and amorphous silicates are the main components of the readily soluble Si pool in HTF soils. The environmental conditions are conducive to clay transformations in the soils. Our data indicate that kaolinite is progressively altered to Mg-rich smectite through mixed-layering, withdrawing Si from the soil porewater.<br>Planícies hipersalinas costeiras (PHCs) são ecossistemas transicionais comumente encontrados em regiões áridas e semiárias. Estes ambientes são encontrados em várias regiões do mundo, tais como Oceania (e.g. Austrália e Nova Caledónia), África (e.g. Senegal, Gambia e Madagascar), América Central (e.g. Nicarágua), América do Sul (e.g. Equador e as costas norte, nordeste e sudeste do Brasil). Por estarem posicionados na transição entre os ecossistemas marinhos e de terras altas, os solos de PHCs devem exercer um controle biogeoquímico na ciclagem de nutrientes (e.g. Si e Fe), afetando o fluxo dos mesmo para o oceano e ecossitemas adjacentes. Este controle biogeoquímico é governado pelas condições fisico-químicas do meio (e.g. pH e salinidade) e pelos processos pedogenéticos atuantes nos solos (e.g. processos redox). Desta forma, o estudo da fração coloidal, da pedogênese e da distribuição do Si nos diferentes componentes do solo possibilita caracterizar detalhadamente os solos de PHCs e desvendar os processos que controlam a dinâmica de Si no ambiente. Portanto, duas PHCs localizadas na costa brasileira foram estudadas e os resultados estão apresentados em três capítulos nesta tese. O primeiro capítulo teve por objetivo investigar a pedogênese em PHCs com base em estudos morfológicos e extrações sequenciais de Fe e Mn. O segundo discute a geoquímica de silício nos solos com base em extrações sequenciais, MEV e modelagem de raios-X da fração argila fina. O terceiro capítulo discorre sobre as características, distribuição e gênese de argilominerais nos solos com base em modelagem de raios-X, MET-EDS, FTIR e FRX. As reações redox parecem controlar a evolução pedogenética nestes solos, as quais levam à mobilização ascendente de Fe2+ e Mn2+ nos perfis, oxidação da pirita e, consequentemente, transformação dos horizontes mais profundos. Estes processos também são responsáveis pela formação de oxihidróxidos de Fe e Mn nos horizontes superiores dos perfis de solo, levando à um controle do Si por reações de co-precipitação e adsorção envolvendo oxihidróxidos de Fe. O Si associado aos oxihidróxidos de Fe e silicatos amorfos são os principais componentes da fração mais solúvel de Si nos solos estudados. As condições ambientais nas PHCs são favoráveis às transformações minerais. Os dados indicam que a caulinita é alterada para esmectitas magnesianas por processos de interestratificação, removendo Si da solução do solo.

In this study, X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), and conventional TEM (CTEM) of Pt-C replicas are used to characterize both synthetic and natural 2:1 clay minerals from a variety of geological environments. In manuscript 1, reference samples of illite and expandable 2:1 clay minerals (i.e., smectite-group minerals, vermiculite and rectorite) varying in interlayer charge were investigated to characterize their interlayer expansion after treatment with octadecylammonium (nC=18) cations. The results of this study show that the treatment of ultrathin sections of 2:1 clay minerals with nC=18 cations and their subsequent investigation under the HRTEM provide information on the distribution of layer charges and layer-charge heterogeneities that cannot be obtained with conventional techniques of sample preparation. The major objective of manuscript 2 is to test whether oxalate catalyzes the crystallization of saponite at low temperatures and pressures. Additionally, the experiments of this study allow the investigation of the expansion behaviour and the structure of newly formed saponite crystals after exchange with n-alkylammonium cations in HRTEM lattice-fringe images. As these clay minerals are interpreted to replicate by template-catalyzed polymerization and transmit the charge distribution from layer to layer, the formation of 2:1 layer silicates with a variable layer-charge has significant implications for the abiotic origin of life. The finding that polar organic molecules such as oxalic acid catalyze clay-mineral formation in the laboratory is of great relevance to what processes may have occurred on carbonaceous chondrites and on the primitive, outgassing Earth that finally led to the evolution of life. In manuscript 3, I investigated the role of oxalate in promoting the nucleation of 2:1 silicate layers of saponite within the low-charge, smectite-like interlayers of rectorite. This study was aimed to test the intercalating hypothesis of Weiss et al. (1969) and Weiss (1981), who claimed to have successfully proven the synthesis of new smectite layers from a solution within the low-charge interlayers of rectorite. Lattice-fringe images show that the oxalate-promoted formation of the new 2:1 layer silicates from the silica gel leads to the alteration and destruction of the rectorite structure. The saponite layers grow independently of any crystallographic orientation given by the rectorite layers. In manuscript 4, XRD, HRTEM and CTEM were used to characterize the clay-mineral separates (2.0-0.5, 0.5-0.1, and &lt;0.1 μm) from argillaceous rocks taken at increasing depth from two wells, North Ben Nevis (NBN) P-93 (2025 m, 2730 m) and Adolphus (AD) D-50 (2035 m, 3135 m) in the Jeanne d'Arc Basin, offshore Newfoundland, in order to understand the diagenetic changes of the 2:1 clay minerals that constitute the smectite to illite (S→I) reaction during progressive burial. Lattice-fringe images of clay minerals in ultrathin sections treated with nC=18 cations show the multiphase nature of the clay-mineral assemblages (e.g., smectite-group minerals, expandable and non-expandable illite, vermiculite) in all size fractions. Conventional TEM images of Pt-C replicas show a change in particle morphology with increasing depth of burial. Irregular, flake-like particles dominate in NBN P-93 at 2025 m and AD D-50 at 2035 m, whereas at greater depths (NBN P-93 at 2730 m and AD D-50 at 3135 m), a larger proportion of lath-like or equidimensional particles are observed. The diagenetic evolution of S→I in the investigated depth interval of the Jeanne d'Arc Basin should be considered as a sequence of multiple discrete 2:1 clay-mineral phases that dissolve and crystallize from solution in overlapping zones of burial depth and not as a single, continuous and progressive reaction-series, as conventionally assumed.<br>Des argiles naturelles et synthétiques provenant de divers milieux géologiques ont été caractérisées par diffraction X et par microscopie électronique en transmission conventionnelle sur répliques Pt-C, et par imagerie à haute résolution sur sections ultraminces.Dans le premier manuscrit, l'effet du traitement avec des cations octadécylammoniac (nC = 18) sur des échantillons d'illite et d'argiles gonflables de type 2:1 (smectites, vermiculite et rectorite) dont la charge des feuillets est variable a été étudié afin de mieux comprendre l'expansion de leur espace interfoliaire. L'imagerie haute résolution de section ultraminces d'argiles de type 2:1 démontre que ce traitement révèle des détails sur la distribution et l'hétérogénéité des charges de leurs feuillets qui échappent aux techniques conventionnelles de préparation de ces minéraux.Dans le deuxième manuscrit, l'effet catalytique de l'oxalate sur la cristallisation de la saponite à 60°C et à pression ambiante est évalué. L'expansion de la saponite néoformée, après son traitement avec les cations nC = 18, est également étudiée en microscopie électronique par transmission à haute résolution. Les feuillets de saponite se répliquent par polymérisation catalysée par une matrice bidimensionnelle et transmettent la distribution de leur charge d'un feuillet à l'autre, une observation aux répercussions importantes sur l'hypothèse d'une origine abiotique de la vie. L'effet catalytique de molécules organiques polaires sur la néoformation d'argiles aurait pu jouer un rôle chez les chondrites carbonées et lors du dégazage de l'atmosphère terrestre précoce, et ainsi contribuer à l'apparition de la vie sur Terre.Dans le troisième manuscrit, j'ai étudié le rôle de l'oxalate dans la nucléation de la saponite, une argile 2:1, à partir de smectite à faible charge interstratifiée dans la rectorite. Ceci fournit un test de l'hypothèse d'intercalation de Weiss et al. (1969) et de Weiss (1981). Ces auteurs ont dit avoir observé la synthèse de smectite à partir de solution au sein de l'espace interfoliaire à faible charge de la rectorite. L'imagerie de franges réticulaires indique toutefois que la néoformation de cristallites de saponite à partir d'un gel de silice, favorisée par la présence d'oxalate, détruit la structure de type 2:1 de la rectorite. Les couches de saponite croissent de façon indépendante de l'orientation cristallographique des couches de rectorite.Dans le quatrième manuscrit, la diffraction X et la microscopie électronique par transmission ont servi à caractériser les fractions concentrées de minéraux argileux (2.0-0.5, 0.5-0.1, et &lt;0.1 μm) à diverses profondeur dans deux puits, North Ben Nevis (NBN) P–93 (2025 m, 2730 m) et Adolphus (AD) D–50 (2035 m, 3135 m), dans le but de mieux comprendre les modifications diagénétiques au cours de l'illitisation de la smectite (S→I) pendant l'enfouissement progressif du bassin Jeanne d'Arc, au large de Terre-Neuve. Les images à haute résolution de franges réticulaires d'argiles traitées avec des cations nC = 18 démontrent la présence de phases multiples (par exemple, smectites aux charges de feuillet faible à forte, illites gonflable ou non, vermiculite) dans toutes les fractions granulométriques. Les images conventionnelles de répliques Pt-C illustrent un changement morphologique progressif avec la profondeur d'enfouissement. Des particules irrégulières et en paillettes prédominent à 2025 m (puits NBN P-93) et à 2035 m (AD D-50), tandis qu'à plus grande profondeur (NBN P-93 à 2730 m, AD D-50 à 3135 m) la proportion de particules en lamelles ou équidimensionnelles augmente. L'évolution diagénétique S→I en fonction de la profondeur du bassin Jeanne d'Arc procède par la dissolution et la croissance en solution de phases minérales 2:1 multiples et distinctes sur des intervalles de profondeur qui se chevauchent, plutôt qu'en une série de réactions progressives et continues telle qu'on les conçoit habituellement.

<p>Because the Coastal Plain of southeastern Virginia has not been extensively studied, thirty random samples associated with Blackwater and Nottoway rivers were collected in the spring of 1987 from Surry, Sussex, and Southampton counties. Soil classification as well as mineralogical, chemical, and physical analysis were conducted for all samples.</p> <p> The purposes of this investigation were to: (1)classify the soils in this area, (2) determine the distribution of sand and clay minerals, (3) examine the weathering effect on clay minerals on different position of the landscape for different parent material sources.</p> <p> The soils examined classified as follow: Aquic Hapludults 43% > Typic Hapludults 26.6% > Ultic Hapludalfs 10% > Humic Hapludults 3% = Typic Rhodudlts 3% = Aquic Hapludalfs 3% = Typic Udipsamment 3% = Typic Quartzpsamment 3% = Psammentic Hapludalfs. Qualitative analysis of clay minerals revealed that kaolinite and hydroxy interlayer vermiculite were the dominant clay minerals; that montmorillonite, mica, gibbsite quartz, and vermiculite were of lesser quantities; that chlorite, feldspar and interstratified minerals were of trace amounts. Kaolinite represents about 21-70%, HlV 11-60%, montmorillonite 0-20%, mica 0-16%, gibbsite 0-13%, quartz 1-12%, and vermiculite 0-10%. The presence of these minerals were mainly related to the acid reaction of the soil media, which was essentially attributed to Al and H ions in soil solution. From the past history and geological composition of the Piedmont it is assumed that kaolinitic minerals were transported and sedimented in the Coastal Plain. Hydroxy-interlayer vermiculite minerals was weathering from vermiculite because most of the Al was adsorbed by vermiculite to form HIV. Therfore, gibbsite was not precipitated. Montmorillonite was assumed to have formed from mica minerals. That was substantiated by statistical analysis which showed a high negative correlation between gibbsite and vermiculite (r=0.46, n=30) and between montmorillonite and mica (r=-0.6, n=10).</p><br>Master of Science

A study has been made of a black and brown Vertisol developed from torbidites in the Appenine highlands of Southern Italy. The investigation includes profile morphology, micromorphology, chemical properties, physical properties and clay mineralogy. In addition digital image analysis techniques were developed to identify and classify features in thin sections generally and specifically in one of the Vertisols. These soils interdigitate on a complex wavy topography. The dark Vertisol has distinct vertic features such as large slickensides, large cracks and self mulching; they are more mature, deeper and generally more fertile. The Brown Vertisols have weakly expressed slickensides and cracks but self-mulching is well manifested; these soils are younger, shallower and less fertile. The study of the thin sections has enabled a detail characterization of many features. A detailed mineralogical study of the clay was carried out. The clay minerals are dominated by smectite. The low charge beidellite and montmorillonite of the parent material change into high charge beidellite in the upper horizons. Both of the soils showed two distinct processes: homogenization and horizon differentiation. Two experiments on digital image analysis were conducted using multivariate classification widely used in remote sensing. In the first investigation multivariate statistical analysis through the creation of multilayer images was achieved using the ERDAS software. A supervised classification applied to a combination of plane transmitted light (PTL) and circularly polarized light (CPL) images allowed the differentiation of quartz, clay coatings, matrix and pores in an Alfisol. With the second experiment using the Semper software a combination of brightness and shape classification has been demonstrated. A series of new techniques have been tested. The classification of the Vertisol used plane polarized light (PPL), CPL, incident UV light and the 2^nd Component of PCT. These enabled the differentiation of very complex features. The procedure was compared with point countings and gave very good results.

CLAY MINERALOGY AND DIAGENESIS OF K-BENTONITES OCCURRING IN THE DEVONIAN YILANLI FORMATION FROM NORTH WESTERN ANATOLIA (BARTIN-ZONGULDAK) &Uuml<br>nl&uuml<br>ce, &Ouml<br>zge M. Sc., Department of Geological Engineering Supervisor: Prof. Dr. Asuman G&uuml<br>nal T&uuml<br>rkmenoglu January 2013, 80 pages Yellowish brown and gray-green colored K-bentonite horizons revealing thicknesses up to 60 cm are exposed within the limestone-dolomitic limestone successions (Middle Devonian-Lower Carboniferous Yilanli formation) deposited on a shallow marine carbonate platform at Zonguldak and Bartin area in the western Black Sea region. In this study, bentonite samples collected from two different locations<br>Gavurpinari quarry and Yilanli Burnu quarry are investigated by means of optical microscopy, X-ray powder diffraction analyses (XRD), both scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) analysis, high resolution transmission electron microscopy (HR-TEM) and inductively coupled plasma mass spectrometry (ICP-MS) in order to reveal their mineralogicalgeochemical characteristics and understand their origin and evolution. Illite is determined as the major phyllosilicate mineral in K-bentonites. Additionally, kaolinite and illite-smectite mixed-layer clay minerals are also detected in some samples. As non-clay minerals calcite, dolomite, quartz, gypsum, feldspar, pyrite and zircon are present in these K-bentonites. Crystal-chemical characteristics (K&uuml<br>bler index-KI, intensity ratios (Ir), illite polytypes (%2M1), (d060) of illite minerals from the two different sampling locations were investigated. Their KI values (for Yilanli Burnu sampling location varying between 0.47-0.93 (with an average of 0.71 &Delta<br>&deg<br>2&theta<br>)<br>for Gavurpinari quarry sampling location varying between 0.69-0.77 (with an average of 0.72 &Delta<br>&deg<br>2&theta<br>))<br>% of swelling component (smectite-max 5%) and crystallite thickness (N=10-20 nm) indicate that these illites were affected by high-grade diagenetic conditions. Similarly, illite polytype ratios (%2M1/(2M1+1Md)) range between 20-50% (with an average of 36%) for the Yilanli Burnu quarry samples, whereas, these ratios are between 25-45% (with an average of 37%) for the Gavurpinari limestone quarry samples. Illite polytpe data also supports a high-grade diagenetic origin possibility of K-bentonites. Illite d060 values ranges between 1.491-1.503 &Aring<br>, (with an average of 1.499 &Aring<br>) which reflect the octahedral Mg+Fe compositions are varying between 0.27-0.51 and thus approach the ideal muscovite-phengite values close to dioctahedral muscovite composition. Based on the data obtained from this study, volcanic ash was firstly transformed into a smectitic I/S mineral in early stages of sedimentation and burial diagenesis. This initial smectite was then be transformed into a highly illitic I/S, and finally illite by diffusion of elements into and out of the bed, during Devonian. Mineralogical-petrographical data points out that these K-bentonites evolved in a high-grade diagenetic environment (approximately 100-150 &deg<br>C) from the products of volcanic eruptions having yet unknown source and distance during Middle-Late Devonian time.

Temporal and spatial variations in intertidal sediment stability are fundamentally governed by the intricate physicochemical properties of cohesive sediment. To further our knowledge of the geomorphological development of these systems and their response to a changing climate, a greater understanding of this relationship between sediment properties and temporal and spatial variations in stability is required. Clay mineralogy is a key sediment property that has received little attention within estuarine erosion studies. The differing characteristic properties of the clay mineral groups are known to be a significant factor in erosion resistance in terrestrial sediment studies. Despite this knowledge there has been little consideration in assessing the significance of this within intertidal settings. Temporal and spatial variations in the surface sediment strength were measured using a Cohesive Strength Meter (CSM) alongside bulk sediment property analysis at 14 sites within four UK estuaries. The influence of clay mineralogy was assessed through a series of CSM laboratory experiments using reconstructed sediments with varying ratios of kaolinite and smectite clays. Multiple regression identified wet bulk density and organic matter (R2 0.76) and particle size, mud content, dry bulk density and porosity (R2 0.84) as the key controls on stability variations within two field study sites. Bed elevation change was identified as a further driver of variations in stability, with strong negative Spearman’s correlations of -0.727 and -0.645 at one study site and a positive correlation of 0.80 observed at a further site. The laboratory study results identify clear differences in erosion thresholds based on clay mineralogy under marine shearing fluids. The greatest erosion thresholds were observed in sediments containing the highest concentrations of smectite. Erosion thresholds reduced in a linear trend (R2 0.97) with decreasing smectite to kaolinite ratio. The use of fresh water as the shearing fluid resulted in a considerable decline in the erosion thresholds of the smectite rich sediments, highlighting the susceptibility of this clay mineral to change in water chemistry. The results of this study contribute essential information on the influence of sediment properties on sediment stability, bridging a crucial gap in the knowledge of cohesive sediment stability within intertidal locations. Furthermore the identification of a relationship between clay mineralogy and sediment stability may lead to improved identification of estuaries that are more likely to be susceptible to erosion under a changing climate.

Commonly the thermal maturity of the Late Devonian to Early Mississippian Woodford shale found on the flanks of the Arbuckle Mountains of Oklahoma is determined by vitrinite reflectance, values ranging from 0.3-1.5%. Using phyllosilicate minerals, specifically diagenetic mixed layer illite/smectite and diagenetic illite, an understanding of the extent and processes leading to the thermal maturation may be developed. Analysis by XRD of the clay mineralogy of the Woodford shale found kaolinite and mixed layer illite/smectite with <5% smectite and R≥3 stacking order. Modeling of the Woodford shale also suggests the percentage of smectite present in mixed layer illite/smectite to be <5% and commonly <2.5%. Deconvolution of the illite (001) peak supports the low smectite content and high illite crystallinity. The long range ordered illite, R≥3, and high illite crystallinity values are indicative of diagenesis to anchizone conditions suggesting a higher thermal maturity relative to previously measured values of vitrinite reflectance.

Many chemical and physical factors govern the mobility of metal contaminants in soils and clay systems; some of these chemical factors include mineralogical composition, cation exchange capacity, organic matter content, pH and the ionic strength of soil water. This makes understanding and therefore predicting the fate of metal contaminants in soils a complex undertaking. There were two broad objectives in this study. The first was to investigate binary and ternary sorption systems, with the aim to understand the effects that factors such as pH, ionic strength, organic matter and metal concentrations, have on sorption of simple clay minerals (bentonite and kaolinite) with metals (cadmium, caesium, nickel and strontium). The second was to investigate the retention of heavy metals and radionuclides by well characterised organic-rich and organic-poor clay soils, breaking them down to their individual components to help understand the effects of each component separately, the study also tested to see if the additivity principle holds for these heavy metals and radionuclides, the additivity principle presumes that the overall sorption behaviour of a complex mixture is a summation of the weighted individual sorption behaviours of its constituents. The study also determined the relationship between the natural organic matter (NOM) content and cation exchange capacity (CEC) of the soils and how these affect the mobility of the metals, while also considering the relative importance of the speciation of the metals. Two British clay soils (Mercia Mudstone and London Clay) and two Nigerian soils (an organic-rich Ikeja Loam and the other organic-poor Magodo Laterite) were characterised by X-ray diffraction (XRD) analysis. Batch techniques were employed for the sorption studies, and radiometric techniques, ICP-OES and ICP-MS were used to quantify metal distribution between phases. The sorption of dissolved organic matter to clay minerals is very dependent on pH; this dependence is greater with increasing concentration of organic matter. The formation of metal-humate complexes is dependent on the nature of the metal and pH. Caesium exhibits no discernible sorption to humic acid, cadmium sorption is enhanced by increasing alkalinity but this enhancement is slightly reduced in higher concentrations of humic acid, nickel sorption is mostly unaffected by pH except in higher concentrations of humic acid and enhanced only under very low concentrations of humic acid, while strontium sorption to humic acid is reduced with increasing alkalinity. The nature and preference of humic acid sorption for these metals are vital to understanding the role played by humic acid in the ternary sorption studies of metals, humic acid and clay minerals. Strongly acidic conditions dominate other factors affecting sorption such as ionic strength in sorption of metals to clay minerals. Caesium sorption to bentonite at pH 4 is poor and almost unaffected by ionic strength of the electrolyte solution; saturation of sorption sites is reached with low amounts of adsorbed caesium. Strontium also binds poorly to bentonite at pH 4, more so than caesium, but an ionic strength effect on sorption still exists and is discernible even under these conditions. Increasing alkalinity has the expected effect of increasing sorption capacity of bentonite for both metals. Bentonite has poor sorption properties, having low affinity for caesium and strontium, but has greater affinity for caesium than strontium. The presence of humic acid can enhance or suppresses sorption, this varies from metal to metal and from solid to solid, the degree of enhancement or suppression also depends on humic acid concentration. Kaolinite has better sorption properties than bentonie. Cadmium has greater sorption affinity for kaolinite in the absence of humic acid, but nickel sorption is more enhanced in the presence of humic acid. Although the presence of humic acid enhances cadmium and nickel sorption to kaolinite, low humic acid concentration provides the best conditions for maximum sorption of both metals. High concentrations of humic acid lead to colloid formation which block access of metals with larger hydration radii to sorption sites while also encouraging the formation of humic acid-metal complexes. As with bentonite, caesium and strontium are both poorly sorbed by kaolinite. Unlike with cadmium and nickel however, the enhancement of strontium sorption is supported by higher concentrations of humic acid, these confirm a greater preference for the formation of S-HA-Sr ternary and lower preference for the formation HA-Sr binary complexes. The presence of humic acid inhibits caesium binding, and retention but this reduces with increasing alkalinity, while the reverse is the case with strontium whose retention is very poor and improved in the presence of humic acid and increasing alkalinity. Both caesium and strontium are poorly sorbed and retained by kaolinite but their retention improves with increasing humic acid concentration and pH. Cadmium and nickel also exhibit poor retention to kaolinite but their retentions are more improved under alkaline conditions and higher humic acid concentrations, nickel more so than cadmium. Similar sorption affinities were exhibited by the British (London Clay and Mercia Mudstone) and Nigerian soils (Magodo Laterite and Ikeja Loam) for the metals studied, showing the significance of soil constituent contribution to sorption behaviour. Both British clay matrices have affinity for the metals in the order Cs >> Cd ≈ Ni >> Sr, London Clay has the greater sorption capacity for all the metals, the clay mineral content of Mercia Mudstone is almost entirely made up of Illite while London Clay contains a mixture of smectite, illite and kaolinite with smectite being the most prevalent clay mineral phase. These confirm that smectite-rich clay systems will exhibit better sorption and retention capacities for metal contaminants. Both Nigerian soils showed the same order of affinity for all the metals Cd >> Ni >> Cs >> Sr, cadmium s preferential sorption to kaolinite was observed in its greater sorption and retention by the Nigerian soils which are kaolinite-rich. This preferential sorption of cadmium by kaolinite is confirmed by the Standard Addition experiment where its contribution to cadmium sorption is clearly evident, a trend not replicated with nickel as the sorbing metal. The presence of organic matter in soils or clay systems improves their metal sorption capacity significantly, especially true for insoluble organic matter, however its significance is reduced as pH increases. The contribution of organic matter also depends on the sorption affinity of the metal for organic matter; metals such like strontium are more affected by organic matter presence. The overall sorption behaviour of complex systems such as soils is difficult to attribute to their individual constituents. The laterite soils can be considered a relatively simple soil system containing only four constituents in significant quantities, yet it is difficult to replicate its sorption behaviour using a replicate proportioned mixture of its constituent phases. The additively calculated sorption profiles for the synthetic laterite were different from those obtained experimentally, the reason for this is that the existence of significant particle size differences between the natural and synthetic soils give rise to differences in the availability of sorption sites which is evident from the different CEC values measured for both systems.

Este trabalho teve como objetivo identificar a mineralogia da matéria-prima utilizadas pelas indústrias cerâmicas do município de Cedro de São João, Sergipe. As áreas trabalhadas são os depósitos aluvionares, constituídos de cascalhos, areias, siltes e argilas; e o Grupo Igreja Nova, cujo interesse está voltado para o Membro Boacica da Formação Batinga, constituído de siltitos laminados, com estratificação cruzada e frequentes gradações para arenitos e folhelhos. A metodologia utilizada iniciou-se com pesquisas bibliográficas a respeito da obtenção de material argiloso no município, junto ao cadastro mineiro do DNPM Departamento Nacional de Produção Mineral. Foram feitos trabalhos de campo, em que foram coletadas 9 amostras nos depósitos aluvionares e na Formação Batinga. A etapa seguinte foi a de análise em laboratório, em que foi utilizada a técnica de difratometria de raios-x para a identificação de minerais. Os resultados encontraram como fases minerais ilita e caulinita, embora não tão expressivas, em amostras da Formação Batinga e quartzo. Nas amostras dos depósitos aluvionares, os minerais identificados não são argilominerais, porém apresenta clorita e mica (muscovita), além da albita e quartzo. Dados do DNPM mostram que os requerimentos de licenciamento do município estão sobre os depósitos aluvionares, enquanto que os processos de autorização de pesquisa e concessão de lavra referem-se às áreas da Formação Batinga, uma vez que é necessário o conhecimento da área, através da autorização de pesquisa para que passe a fase de concessão de lavra. As conclusões deste trabalho podem subsidiar interesses acadêmicos e comerciais sobre as substâncias extraídas pelas indústrias cerâmicas na região.

no<br>Marls were identified from a range of European sources and assessed for their Cementation Index, as proposed by Eckel. Two were selected for calcination in a laboratory kiln; one from Folwark in Poland (CI 1.75) and one from Lillienfeld in Austria (CI 2.03). Analysis of historical documents, while not revealing precise kiln conditions, does suggest that they were such as not to yield complete decarbonation of the calcite. Consequently, a series of calcinations was undertaken in which the peak temperature control of the kiln was set in the range 730°C to 1100°C, with residence times in the range 150 to 1250 min. The airflow through the kiln was sufficient to maintain a minimum oxygen content of at least 12 %. The resulting clinker was ground to comply with the 19th century Austrian Norme. Pastes were produced at w/c = 0.65 and assessed for setting time and strength development (6 h to 1 year). Both parameters were highly dependent upon calcination conditions with both ¿low¿ and ¿high¿ calcinations producing slower setting and slower strength development than intermediate conditions. Two strength development profiles were identified; one being the expected continuous increase of strength, albeit with a declining rate of increase with time, while the other showed a three-step sequence of high initial strength, a dormant period which could last for many weeks and a final increase in strength to an age of one year. The cements were compared using X-ray diffraction (XRD). Considerable variation in the composition was noted and related to the calcination conditions. Of particular interest is the formation of both ¿'-belite and ß-belite under differing calcination conditions. Clinker particles were also compared using the SEM in back-scattered electron imaging mode and the development of morphology observed.

Thesis (MScAgric)--University of Stellenbosch, 2001.<br>ENGLISH ABSTRACT: This study is an integral part of a multidisciplinary research project concerning the effects of soil and climate on wine quality. The motive, which led to the setting up of this project, was that producers could not determine beforehand whether a specific location would yield wines of high or low quality. If a specific cultivar were to be planted at the wrong location, then it was likely that wine of table quality would result, rather than the export quality wine that was intended. The long term objectives of this multidisciplinary project were the compilation of guidelines by means of which different sites may be classified according to their potential for the production of high quality wines, and the identification of the most important climatic and soil factors responsible for differences in wine quality and character. In this multidisciplinary project, measurements (soil water, leaf water potential, cane mass and yield) were made under dry land conditions in Sauvignon blanc vineyards at six different localities: five in the Stellenbosch district (Simonsberg, Kuils River, Helshoogte, Papegaaiberg and Devon Valley) and one in Durbanville. Each vineyard was owned by a private commercial producer. The vines were approximately 10 years old in all cases, and were trained on a hedge system. Measurements were made in plots, each of which contained 20 vines. Two different soil types were identified at each locality. Vine growth and wine quality differed markedly on these contrasting soils, even though they were located in close physical proximity. The measurements that were made at high and low production plots at each locality during this study were obtained from points which were not more than 60 m metres apart. An automatic weather station was erected halfway between the two, contrasting, experimental plots. Within the overall scope of the multidisciplinary project, the study which forms the subject of this thesis, concentrated on the effects of soil parent material as a soil forming parameter and as a possible predetermining character with regard to vine growth and wine character. From literature it was clear at the outset of this work that the geology of the coastal wine region is very complex and varies over short distances. The geological history indicates different types of rock formation and rock forming process (sedimentary, igneous as well as metamorphic), plate tectonic activity, mountain building, erosion and weathering, over a period of approximately 1 000 million years. The present landscape includes a coastal plane, hills, and eroding mountains. Statistical analyses indicated that the soils from the different localities could mainly be characterised in terms of differences in their sand size fractions. Soils from Durbanville are dominated by fine sand and correlates with the underlying phyllitic shales. Soils from Kuils River contain significantly more coarse sand when compared with the other sites. This appears to be a reflection of the underlying coarse granitic material, and implies that in situ weathering played an important role in soil development. .The data did not, however, prove that the Kuils River soils formed solely from underlying rocks. The gravel and stone fraction for the Kuils River soils were nevertheless correlated with those of the underlying parent material. Soils from Helshoogte and Simonsberg (both of which are underlain by granites), Papegaaiberg and Devon Valley (both underlain by hornfels) were not significantly dominated by any particular sand fraction. Soils from these localities therefore did not only reflect the underlying material as a source of soil parent material. This implied mixing of parent material and/or the incursion of eolian sand at Helshoogte, Simonsberg and Devon Valley. A marine incursion may have affected the soil parent material at Papegaaiberg. In order to obtain more information concerning the origins and possible mixing of parent materials prior to and during soil formation, samples from the different soil horizons in each profile were subjected to a chemical analysis. Particular emphasis was placed on potassium, which is an extremely important nutrient mineral element, from the viewpoints of vine growth and wine quality. Because the soils used in this study were all located in production vineyards, the probability that fertiliser residues would have contaminated the soils was high. The lower soil horizons were considered to be least affected by this contamination and therefore most likely to be indicative of the natural soil chemical composition. However, the lower horizon K content of the soils in this study could not be reliably correlated with any known or predicted characteristic that might link the soil parent material with local rock types. At Durbanville, both soils contained small quantities of K in the lower horizons, reflecting the underlying phyllitic shales, but at Devon Valley and Papegaaiberg, the lower horizons contained more K than expected. The soils at these localities are situated on hornfels, containing low quantities of K. The large quantities of K in the soils may have indicated that these soils are situated close to a granite/Malmesbury contact zone. Soils from Kuils River, Simonsberg and Helshoogte are situated on K-rich porhyritic granites and it was expected that these soils would contain relatively large quantities of K in the lower horizons. This, however, was not the case. It was therefore concluded that dilution with K-poor material had taken place. Such material could have been derived from higher-lying sandstones, or from eolian processes during the Cenozoic. Alternatively, the K content of the soil might have been depleted by long continued leaching. A semi-quantitative analysis of the minerals in the soil clay fractions was also carried out. The objective was to identify the clay minerals that were present in the different soil horizons and to relate the minerals to weathering conditions. Evidence linking the minerals in the clay fractions of the soil samples with the mineralogical composition of the soil parent materials was sought. The clay fraction mineralogy data indicated that all soils in the study area are in an advanced stage of weathering and are dominated by kaolinite, and in certain soils quartz. It was difficult to relate these minerals directly with soil parent material because the primary minerals originating from the soil parent materials have been extensively broken down. The simultaneous presence of quartz and gibbsite in the clay fraction of both soils at Simonsberg, Helshoogte and Durbanville as well as one soil form from bath Kuils River and Simonsberg, indicated non-uniform distribution of clay fraction minerals, indicating that different stages of weathering were present during soil formation. This could have been a result of mixing of parent materials, but may also reflect different periods of weathering of the same material. Both soils at Papegaaiberg, both soils at Devon Valley and other soils at Simonsberg and Kuils River indicated uniform clay fraction mineralogy distribution, mainly because the absence of gibbsite is related to the presence of quartz in the clay fraction. The soil characteristics, as determined in this study, were also compared with vine growth, wine quality and wine character, as obtained in the broader multidisciplinary research project. For most soils in this study, an increase in clay fraction kaolinite was associated with a reduction in vegetative growth, overall wine quality, and fresh vegetative character. An increase in clay fraction quartz was associated with higher overall wine quality. Increased shoot growth also affected fresh vegetative character positively. Better growth occurred on higher altitudes and this resulted, for Sauvignon blanc, in higher wine quality. Wines produced from vines situated on both phyllitic shales and porhyritic granites showed high quality (Durbanville and Helshoogte), but both were related to low clay fraction kaolinite content and high altitude. It was not possible to relate parent material directly with vine growth, wine quality and/or wine character. The lowest quality wines, however, were produced from vines situated on hornfels (Papegaaiberg and Devon Valley), both containing high quantities of clay fraction kaolinite and situated on low altitudes. High levels of K in soils containing high levels of clay fraction kaolinite may have been partly responsible for low wine quality obtained on such soils.<br>AFRIKAANSE OPSOMMING: Hierdie studie vorm 'n integrale deel van 'n multi-dissiplinêre navorsingsprojek oor die effek van grond en klimaat op wynkwaliteit. Die motivering wat gelei het tot die beplanning van hierdie projek, was dat produsente nie vooraf kon bepaal of 'n spesifieke lokaliteit wyne kan produseer van hoë of lae kwaliteit nie. Indien 'n spesifieke kultivar op die verkeerde lokaliteit geplant word, sou dit waarskynlik tot In gewone tafelwyn lei, instede van 'n wyn van uitvoergehalte. Die langtermyn doelwitte van die multi-dissiplinêre projek was om riglyne te ontwikkel om verskillende lokaliteite te klassifiseer na aanleiding van·hul potensiaal om hoë kwaliteit wyne te produseer, asook om die belangrikste klimaats- en grondfaktore verantwoordelik vir die produksie van hoê kwalitiet wyne te identifiseer. In hierdie multidissiplinêre projek was metings (plant beskikbare water, blaarwater potensiaal, lootmassa en oes) onder droêland toestande bepaal in Sauvignon blanc wingerde by ses verskillende lokaliteite: vyf in die Stellenbosch distrik (Simonsberg, Kuilsrivier, Helshoogte, Papegaaiberg and Devon Valley) en een in Durbanville. Elke wingerd is besit deur 'n kommersiêle privaatprodusent. Die stokke was ongeveer 10 jaar oud in alle gevalle en opgelei op 'n heining sisteem. Metings was in eksperimentele blokke van 20 stokke elk uitgevoer. Twee verskillende grondtipes is by elke lokaliteit identifiseer. Lootgroei en wynkwaliteit het merkbaar verskilop die kontrasterende gronde, selfs waar gronde nabyaanmekaar was. Die metings is Liitgevoer op hoë- en lae produksie eksperimentele blokke waar gronde by spesifieke lokaliteite nie verder as 60 meter was nie. 'n Outomatiese weerstasie was halfpad tussen die twee kontrasterende grondtipes by elk van die ses lokaliteite opgerig. Binne die algemene omvang van die multi-clissiplinêre projek, het die studie wat die onderwerp van hierdie tesis is, gekonsentreer op die effek van moedermateriaal as grondvormende parameter asook as moontlike voorspeller van wingerdgroei en wynkarakter. Dit was duidelik uit die literatuur dat die geologie van die Wynkusstreek baie kompleks is en oor kort afstande varieer. Die geologiese geskiedenis dui daarop dat verskillende tipes gesteentes en verskillende prosesse van gesteente-vorming (sedimentêr, stollings- en metamorfe), plaattektoniese aktiwiteit, orogenese, erosie en verwering, oor 'n periode van ongeveer 1 000 miljoen jaar plaasgevind het. Die huidige landskap sluit kusvlaktes, heuwels en geêrodeerde berge in. Statistiese analises het aangetoon dat die gronde van die verskillende lokaliteite hoofsaaklik in terme van verskille in sandgrootte fraksies onderskei kon word. Gronde van Durbanville is gedomineer deur fyn sand en korreleer met onderliggende fillietiese skalies. Gronde van Kuilsrivier bevat betekenisvol meer growwe sand wanneer dit vergelyk word met die ander lokaliteite. Dit is waarskynlik afkomstig vanaf die onderliggende growwe granitiese materiaal en impliseer dat in situ verwering 'n belangrike rol gespeel het in grondontwikkeling. Die data het egter nie bewys dat die gronde van Kuilsrivier slegs uit die onderliggende graniete gevorm het nie. Die gruisfraksies in die gronde by Kuilsrivier was tog vergelykbaar met die onderliggende materiaal. Gronde vanaf Helshoogte and Simonsberg (beide onderlê deur graniete), Papegaaiberg and Devon Valley (beide onderlê deur hornfels) was nie betekenisvol gedomineer deur 'n spesifieke sandfraksie nie. Gronde vanaf hierdie lokaliteite het dus nie slegs die onderliggende gesteentes verteenwoordig nie. Dit dui op vermenging van moedermateriaal en/of eoliese prosesse by Helshoogte, Simonsberg and Devon Valley. 'n Styging in seevlak kon die moedermateriaal by Papegaaiberg beïnvloed het. Om meer inligting omtrent die oorsprong en moontlike vermening van moedermateriaal voor grondvorming te verkry, is die verskillende grondmonsters chemies ontleed. Kalium is In uiters belangrike voedingselement wat lootgroei en wynkwaliteit kan beïnvloed. Aangesien die gronde in hierdie studie in bestaande produksieblokke voorkom, was daar 'n goeie kans dat bemestingstowwe die chemiese samestelling kon beïnvloed. Die C horisonte van die verskillende gronde was beskou as dié wat die minste deur bemesting beYnvloedsou word en die naaste aanduiding van natuurlike grondchemiese samestelling. Die C horison K-inhoude van die gronde in die studie het egter nie gekorreleer met enige eienskap wat die moedermateriaal van die gronde met die lokale gesteentetipe kon verbind nie. By Durbanville, het beide gronde klein hoeveelhede K in die C horisonte bevat, wat die onderliggende fillietiese skalies reflekteer, maar by Devon Valley en Papegaaiberg, het die C horisonte meer K bevat as wat verwag is. Die gronde by hierdie lokaliteite word onderlê deur hornfels, wat lae hoeveelhede K bevat. Die groot hoeveelhede K in hierdie gronde dui moontlik op 'n kontaksone tussen graniet en Malmesbury gesteentes in die area. Gronde vanaf Kuilsrivier, Simonsberg en Helshoogte word onderlê deur K-ryke porfiritiese graniete wat groot hoeveelhede K in die ondergronde sou bevat. Dit was egter nie die geval nie en dit was aanvaar dat verdunning van K-arme materiaal plaasgevind het. Die oorsprong van Karme materiaal was waarskynlik vanaf hoêr-liggende sandstene, of vanaf eoliese prosesse gedurende die Cenozoikum. Alternatiewelik is K inhoude van die gronde verlaag deur lang en aanhoudende loging. 'n Semi-kwantitatiewe analise van minerale in die kleifraksie was uitgevoer om te bepaal watter minerale in die kleifraksie van die verskillende gronde teenwoordig is en om die minerale met stadia van verwering te vergelyk. Dan kon die mineralogiese samestelling in verband met moedermateriaal gebring word. Resultate het aangetoon dat al die gronde in die studie in 'n gevorderde stadium van verwering is en gedomineer word deur kaoliniet, en in sekere gronde, klei fraksie kwarts. Aangesien die primêre minerale in 'n groot mate afgebreek is, was dit moeilik om die minerale in die kleifraksie direk in verband met moedermateriaal te bring. Die voorkoms van kwarts en gibbsiet in die kleifraksie in beide gronde van Simonsberg, Helshoogte en Durbanville asook een grondvorm vanaf beide Kuilsrivier en Simonsberg, het aangetoon dat verskillende stadia van verwering gedurende grondvorming in hierdie gronde voorgekom het. Dit kan die gevolg wees van vermenging van verskillende moedermateriaal, maar kan ook verskillende periodes van verwering van dieselfde materiaal aandui. Beide gronde by Papegaaiberg, beide gronde van Devon Valley die ander gronde by Simonsberg en Kuilsrivier het slegs een fase van verwering tydens grondvorming aangedui, hoofsaaklik as gevolg van die afwesigheid van gibbsiet wanneer kwarts voorkom. Grondeienskappe, soos bepaal in hierdie studie, was ook vergelyk met lootgroei, wynkwaliteit en wynkarakter, soos verkry uit die resultate van die multi-dissiplinêre projek. Vir die meeste gronde in die studie was 'n toename in kleifraksie kaoliniet geassosieer met afname in vegetatiewe groei, algemene wynkwaliteit, asook vars vegetatiewe wynkarakter. 'n Toename in kleifraksie kwarts was geassosieer met hoër algehele wynkwaliteit. 'n Toeneme in vegetatiewe groei het ook die vars vegetatiewe karakter van die wyn positief beïnvloed. Beter vegetatiewe groei het op hoër hoogtes voorgekom en dit het gelei tot hoër wynkwaliteit vir Sauvignon blanc. Wyne afkomstig van wingerde op beide fillietiese skalies en porfiritiese graniete, was van hoër kwaliteit (Durbanville and Helshoogte), maar beide was geassosieer met lae kleifraksie kaoliniet en hoë ligging. Dit was nie moontlik om moedermateriaal direk met vegetatiewe groei, wynkwaliteit en/of wynkarakter te vergelyk nie. Wyne met die laagste kwaliteit kom egter voor op hornfels (Papegaaiberg and Devon Valley), wat beide groot hoeveelhede kleifraksie kaoliniet bevat en geleê is op lae hoogtes. Hoê vlakke van K in gronde wat groot hoeveelhede kleifraksie kaoliniet bevat kan gedeeltelik verantwoordelik wees vir lae kwaliteit wyne op sulke gronde.

Master of Science<br>Department of Agronomy<br>Michel D. Ransom<br>Factors governing potassium fixation and release are poorly understood. This study was conducted to investigate the effects of clay mineralogy and structural iron oxidation state on potassium fixation. Five reference clays and two soil clays were used to capture a range in mineralogical compositions and potassium behaviors. Reference clays used were illite (IMt-1), kaolinite (KGa-1b), montmorillonite (STx-1b), nontronite (NAu-2), and vermiculite (VTx-1). Soil clays used were from the upper 15 cm of a Belvue loam (BEL) and a Cherokee silt (CHE). Potassium fixation capacities were measured on unaltered as well as sodium dithionite reduced forms of each clay. Ferrous and total iron contents were determined photometrically using 1, 10-phenanthroline. Potassium fixation was measured by potassium saturating the clays and washing off exchangeable and solution potassium with solutions of magnesium chloride; samples were then acid digested and the amount fixed was calculated as the amount of potassium in the acid digestion minus the amount originally in the sample. BEL released potassium rather than fixed it while CHE tended to release potassium in the unaltered form and fix potassium in the reduced form. Structural iron reduction significantly impacted the amounts of potassium fixed by VTx-1 and NAu-2, which had the highest total iron contents of all the clays evaluated. NAu-2 and VTx-1 both on average fixed less than 1 mg K g clay[superscript]-1 in the unaltered form and an average of 6 and 11 mg K g clay[superscript]-1, respectively, in the reduced form. Regardless of being in the unaltered or reduced form, KGa-1b fixed essentially no potassium and IMt-1 and STx-1b fixed intermediate amounts of potassium—2 to 4 mg K g clay[superscript]-1 on average. The effects of clay mineralogy and structural iron oxidation state on potassium fixation can largely be explained through an understanding of layer type, layer charge, and charge distribution. In order for potassium fixation to occur, interlayer sites need to be accessible and available. Generally, the greater the negative layer charge the greater the amounts of fixation, with tetrahedral layer charge favoring fixation more than octahedral layer charge, and layer charge being a function of structural iron oxidation state.

L'étude des sols argileux fait l'objet de nombreux travaux motivés par leur rôle dans les processus d'érosion, les catastrophes naturelles et l'agriculture de précision. La caractérisation du contenu en argiles gonflantes du sol est aussi nécessaire pour évaluer la traficabilité d’une région ou le risque de retrait-gonflement des sols, responsable d’engendrer des dégâts sur le bâti. En effet, les argiles gonflantes sont des smectites qu'il faut différencier des autres types d'argiles telles que l'illite ou la kaolinite, en milieu tempéré. Les techniques traditionnelles pour réaliser la cartographie des minéraux argileux des sols sont en général couteuses, financièrement et en temps et sont basées sur des campagnes terrain intensives simultanément à des acquisitions photographiques afin de spatialiser l'information qui reste qualitative. La télédétection hyperspectrale est une technique potentiellement intéressante pour obtenir des cartes d'argile plus précises et à moindre coût. Néanmoins, elle est limitée par le fait que (i) les minéraux sont mélangés de manière intime dans les sols avec d’autres composants; mais aussi que (ii) à l’échelle aéroportée, le signal réfléchi au sein d’un pixel (résolution spatiale de l’ordre du mètre) comprend de la végétation en plus du sol nu. Ces phénomènes de mélange, aux échelles microscopique et macroscopique, rendent difficile l’estimation du contenu en argiles minéralogiques. Le développement des drones ainsi que leur possibilité d'embarquer de nouvelles caméras hyperspectrales couvrant l'ensemble du spectre [0,4 - 2,5 µm] avec une haute résolution spatiale (environ 10 cm) et un signal à bruit élevé ouvrent la voie à un inventaire plus précis des argiles.L'objectif de cette thèse est de montrer l'intérêt de l'utilisation de méthodes de démélange sur des données hyperspectrales à très haute résolution spatiale pour estimer le contenu en minéraux argileux du sol, et plus précisément des argiles responsables du retrait-gonflement, les smectites. Dans un premier temps, les méthodes existantes de détection, de caractérisation des différents types d'argile et d'estimation de leur abondance sont présentées. Les potentialités des méthodes de démélange existantes dans la littérature pour l’estimation du contenu en minéraux argileux des sols sont mises en avant. Dans un second temps, les méthodes de démélange sont utilisées sur une base de données d’images hyperspectrale acquises en laboratoire de mélanges contrôlés minéraux contenant des argiles (montmorillonite, illite, kaolinite) et d’autres minéraux présents dans les sols (quartz, calcite). Comme les minéraux sont mélangés de manière intime, des méthodes de démélange, linéaires et non-linéaires sont décrites et comparées. Néanmoins, les algorithmes non-linéaires ont des performances similaires aux algorithmes linéaires. De plus, l’effet de la variabilité des données sur la précision de l’estimation des abondances a pu être réduit en utilisant des prétraitements spectraux. Dans une dernière étape, la comparaison des méthodes de démélange sont étendues à des mesures en environnement extérieur. Cette analyse repose sur une campagne de mesure en extérieur réalisée pour la mesure d'images hyperspectrales acquises depuis une nacelle (12 m de hauteur environ, 1,5 cm de résolution spatiale), et l’acquisition d’échantillons prélevés et analysés par DRX (données quantitatives des abondances des minéraux) pour validation. Cette dernière phase permet d'analyser l'impact d'un sol naturel (composé d'un mélange minéralogique, des matières carbonées telles que la cellulose, et ayant une rugosité de surface…) sur les méthodes de démélange. Les performances obtenues (moins de 15% RMSE sur l’estimation de la montmorillonite) permettent d’ouvrir des perspectives quant à l’application de ces méthodes sur des capteurs embarqués par drone, pour la cartographie de la traficabilité et de l’aléa de retrait-gonflement des sols<br>Clayey soils are studied because of the importance of soils in erosion processes, natural disasters and precision agriculture. Mapping of clay mineralogy is essential for surveying and predicting trafficability and ground instability hazards, such as shrink-swelling, in order to cope with damages caused by expansive soils on infrastructures. Clay minerals in temperate zone soils are mainly divided in smectites, which highly contribute to soil swelling, illite and kaolinite. Geotechnical engineering practice for clayey soils mapping are expensive and time-consuming. Indeed, it is based on field and extensive laboratory studies. In addition, spatial distribution of clay is assessed using aerial photographs and low-scale geological maps. Thereby, small heterogeneities in geological features are rarely detected, and spatial information remains qualitative. Hyperspectral remote sensing could be an alternative to conventional methods for clay mapping. However, this method is limited by two facts: (i) soils are an intimate mixture of minerals, and (ii) vegetation is mixed with bare soil within airborne sensors pixels (meter range of spatial resolution). Those mixtures (at microscopic and macroscopic scales) mask clays specific spectral signatures and limit clay mineral quantification. Recent development in UAV offers new possibilities for carrying hyperspectral cameras in the reflective domain [0.4 – 2.5 µm], and obtaining data with higher SNR and resolution (10 cm). These advances open new perspectives for accurate and less expensive clay maps. This PhD thesis aims to present the potentiality of clay mapping in soils using very-high spatial resolution hyperspectral data, and more specifically, to estimate swelling clay minerals (smectite) abundances. First, existing methods of detection, and abundance estimation of clay minerals are presented. Second, unmixing methods are used on a database of hyperspectral images of controlled mixtures with different abundances of clay minerals, (illite, montmorillonite and kaolinite) and other minerals existing in soils (quartz, calcite). Due to the intimate nature of mixtures, linear and non-linear unmixing methods are described and compared. However, linear and nonlinear algorithms exhibit similar performances. Moreover, the accuracy of estimation of abundances of mineral clay increased using spectral preprocessings. Regarding the third step, field measurements are used to assess clay unmixing methods. This study is based on an outdoor experiment which acquired hyperspectral images from a bucket truck (12 m elevation, 1.5 cm ground sampling distance), and a sampling collection analyzed by XRD (quantitative analysis of mineral abundances) for validation. This step analyzed effects of a natural soil, (with organic matter, a larger diversity of mineralogical components and with surface roughness) on unmixing methods tested with laboratory data. Obtained performances (less than 15% RMSE for montmorillonite estimation) allow perspectives to apply these methods on data obtained with UAV sensors, for trafficability or expansive soils mapping purposes

Thesis (M.S.)--Georgia State University, 2005.<br>Title from title screen. Beth A. Christensen, committee chair; W. Crawford Elliott, Eirik J. Krogstad, Deborah Freile, committee members. Description based on contents viewed Dec. 22, 2006. Includes bibliographical references (p. 107-112).

Le Sud du Brésil est une région où l'agriculture est très intensive et la pression sur les sols est beaucoup plus importante que dans la région amazonienne. Ainsi, il est nécessaire de développer des études qui relient le développement du sol avec son matériau source respectif, en détaillant les transformations dans la zone de transition sol-roche et ses implications pour les activités environnementales et humaines. Dans ce contexte, ce travail vise à: (i) caractériser les aspects minéralogique, pédochimique et géochimiquedes profils d'altération développés en l'absence d'action humaine ou avec une intervention minimale; (ii) caractériser qualitativement et semi-quantitativement les minéraux primaires et les minéraux pedogenic dans les sols insérés dans les régions importantes de l'écosystème du Rio Grande do Sul; et (iii) évaluer l'impact des différentes intensités de pâturage sur la minéralogie d’un Oxisol sous système intégré de production soja-élevage dans le sud du Brésil. Cette étude concerce des sols du Rio Grande do Sul dont le climat subtropical (températures moyennes annuelles ~17°C, précipitations moyennes annuelles ~1800 mm/an) favorise l’accumulation de matiére organique ainsi que la formation de minéraux argileux 2:1. Les indices d'altération (Weathering Intensity Scale - WIS et Chemical Index of Alteration - CIA) établis à partir de la composition chimique des profils d'altération permettent de classer les profils selon leur degré d’altération qui correspond également à des compositions minéralogiques différentes (smectite, smectite + kaolinite, kaolinite). L'étude a montré que des sols formés à partir de la même roche ont des différences importantes liées aux différences climatiques et de relief. Finalement, après 12 ans de culture des sols avec un système intégré culture-élevage, les surfaces non pâturées présentent une proportions moins important de minéraux 2:1. D'autre part, les surfaces sous pâturage intensif et pâturage modéré présentent un comportement similaire attribué à une aluminisation plus élevée de la couche interfoliaire de minéraux 2:1. L'aluminisation plus élevée sous gestion intensive et modérée peut fixer une partie de l'aluminium dans la phase solide du sol, ce qui pourrait le rendre moins disponible pour les plantes et diminuer sa phytotoxicité.<br>O sul do Brasil é uma região com uma agricultura muito intensa e com grande pressão de uso do solo, consideravelmente mais intenso do que na região da Amazônia. Assim, é necessário desenvolver estudos que relacionem o desenvolvimento do solo com seu respectivo material de origem, detalhando as transformações na zona de transição solo-rocha e suas implicações para as atividades ambientais e humanas. Neste contexto, este trabalho tem como objetivo: (i) caracterizar os aspectos mineralógicos, pedoquimicos e geoquimicos dos perfis de alteração desenvolvidos na ausência ou mínima ação humana; (ii) caracterizar qualitativa e semi-quantitativamente os minerais primários e os minerais pedogênicos em solos inseridos em regiões ecossistêmicas importantes do Rio Grande do Sul; e (iii) avaliar o impacto de diferentes intensidades de pastejo na mineralogia de um Latossolo, sob sistema de produção integrada soja-bovinos de corte no sul do Brasil.Este estudo foi realizado em solos do Rio Grande do Sul, onde o clima subtropical (temperatura média anual ~ 17°C, precipitação anual média de 1800mm/ano) favorece o acúmulo de matéria orgânica ea ocorrência de argilominerais 2:1.Os índices de intemperismo (Weathering Intensity Scale - WIS e Chemical Index of Alteration - CIA), considerando a composição mineralógica dos perfis de alteração, indicaram a seguinte sequência crescente do grau de intemperismo: esmectita < caulinita - esmectita < caulinita. O estudo mostrou diferenças importantes nos solos, mesmo entre aqueles formados a partir do mesmo material de origem, devido às diferenças climáticas e de relevo. Por fim, após 12 anos sob um sistema integrado de produção de soja-bovinos de corte, as áreas não pastejadas apresentaram menor intensidade para os argilominerais 2:1. Por outro lado, as áreas sob pastejo intensivo e pastejo moderado apresentaram comportamento semelhante, devido à maior aluminização da entrecamada dos argilominerais 2:1. A maior aluminização sob pastejo intensivo e moderado pode ser um dreno de alumínio na fase sólida do solo, tornando-o menos disponível para as plantas e diminuindo sua fitotoxicidade.<br>The Southern Brazil is a region with a very intensive agriculture and the pressure on soil use is considerably more intense than in the Amazonian region. Thus, it is necessary to develop studies that relate the soil development with its respective source material, detailing the transformations in the soil-rock transition zone and its implications for the environmental and human activities. In this context, this work aims to: (i) characterize the mineralogical and pedochemical alterations and geochemical evolution the profiles of the alteration developed in the absence, or the minimal human action; (ii) characterize both qualitatively and semi-quantitatively the primary and pedogenic minerals present in soils of important ecosystems in Rio Grande do Sul; And (iii) evaluate the effect of grazing intensities on the mineralogy of an Oxisol, in an integrated soybean-cattle beef production system of southern Brazil. This study concerns soils of Rio Grande do Sul, where the subtropical climate (mean annual temperature ~17°C, mean annual precipitation 1800mm/yr) favored the accumulation of organic matter and occurrence of 2:1 clay minerals. The indexes of weathering (Weathering Intensity Scale - WIS and Chemical Index of Alteration - CIA), considering the mineralogical composition of the alteration profiles, indicated the following increasing sequence of the degree of weathering: smectite composition <kaolinite-smectite composition <kaolinite composition. The study showed that the soils have important differences, even between those formed from the same material of origin, due to climatic differences and relief. Lastly, after 12 years under an integrated soybean–beef cattle production system, the ungrazed areas presented lower intensity of 2:1 minerals. On the other hand, areas under intensive grazing and moderate grazing presented similar behaviour due to the higher aluminization of the interlayer of 2:1 minerals. The higher aluminization under intensive and moderate grazing managements may be a drain on aluminum in the soil solid phase, making it less available to plants and decreasing its phytotoxicity.

Este trabalho apresenta a quantificação da expansão e suas características, principalmente a influência da sucção, em amostras de materiais sedimentares argilosos provenientes da Formação Corumbataí, aflorantes no interior do estado de São Paulo. Foram testadas amostras indeformadas, e amostras destorroadas e compactadas em diferentes umidades, em ensaios de pressão de expansão a volume constante por inundação, e também, com sucção controlada por meio da técnica da transferência de vapor. Foram ensaiadas, ainda, misturas compactadas desse material com bentonita em diferentes proporções, e misturas de bentonita com material não expansivo arenoso oriundo da Formação Botucatu. O controle de sucção foi realizado pelo uso de soluções salinas de NaCl em concentrações preparadas para impor sucções de 40.000, 25.000, 10.000 e 5.000 kPa. Para a realização dos ensaios, construiu-se um sistema de aplicação de cargas e de aquisição automática dos dados de pressão. Para acelerar o processo de umedecimento por vapor, utilizou-se um reservatório externo ligado em uma bomba de ar adaptada para promover a circulação do vapor de ar para dentro da célula edométrica, especialmente construída para esta pesquisa. Os resultados de expansão nos ensaios com inundação mostraram pressões de expansão crescentes com a diminuição dos teores de umidade, e consequente aumento da sucção inicial das amostras ensaiadas, bem como crescentes com o aumento na proporção de bentonita nas misturas, com valores máximos em torno de 700 kPa para o ensaio com a bentonita pura compactada seca. A análise da microestrutura das amostras por meio da porosimetria por intrusão de mercúrio permitiu constatar que as amostras indeformadas apresentaram variação, apenas, nos macroporos após a expansão; e as compactadas na umidade ótima e, posteriormente secas ao ar, não mostraram evolução significativa após a expansão. Na microscopia eletrônica de varredura (MEV) foi possível verificar a mudança nos vazios das amostras, bem como, visualizar a variação na estrutura e na textura. Além disso, no MEV foram confirmados, também, os argilominerais determinados na caracterização mineralógica. Os resultados dos ensaios de expansão com sucção controlada mostraram ausência de pressão de expansão para as amostras da Formação Corumbataí nas condições indeformada, e na condição compactada na umidade ótima e posteriormente seca ao ar. No entanto, esse material, quando compactado seco na forma de pó, e também, compactado seco misturado com bentonita em diferentes proporções, revelou pressões de expansão com a transferência de vapor, assim como, as misturas de bentonita com material não expansivo da Formação Botucatu. A ausência de expansão foi justificada pela forma lenta de umedecimento proporcionada pela transferência de vapor que, apesar de promover o aumento do teor de umidade das amostras, não mobilizou variação volumétrica suficientemente capaz de transmitir como pressão de expansão. Portanto, os ensaios de expansão, com a utilização da técnica de transferência de vapor, foram efetivos para avaliar a expansão somente nos casos em que argilominerais com potencial expansivo estavam presentes em proporções consideráveis.<br>This thesis presents the quantification and characterization of expansion, especially the influence of suction on samples of sedimentary materials from Corumbatai Formation that occurs in Sao Paulo. Undisturbed and compacted samples with different moisture contents were tested with swelling pressure tests at constant volume method by flooding, and also with suction control by vapour transfer technique. Compacted mixtures of this material with bentonite in differents proportions, and mixtures of bentonite with sandy non-expansive material from the Botucatu Formation were also tested. The suction control was performed by the use of NaCl salt solutions at concentrations prepared to perform 40,000, 25,000, 10,000 and 5,000 kPa suctions. For the tests, it was developed a system for load application and automatic retrieval of pressure. To accelerate the wetting process by vapour, we used an external reservoir connected to an air pump adapted to promote air circulation inside the edometric cell, specially made for this study. The expansion results in flooding tests showed increasing swelling pressure with decreasing moisture content. Consequently there was an increase in the initial suction of the tested samples, which kept increasing as the rate of bentonite was raised in the mixtures, with a peak of ca. 700 kPa for the test with dry pure bentonite compacted. In the microstructure analysis of the samples by mercury intrusion porosimetry, the samples showed variation only in macropores after swell; and the ones compacted at optimum moisture, and subsequently air dried, showed no significant change after the swell. In scanning electron microscopy (SEM) it was possible to verify the change in the voids of the samples, as well as to visualize the variation in the structure and texture. In addition, the SEM confirmed clay minerals deterninated in mineralogical characterization. The results of controlled suction with swell tests showed absence of swell pressure for Corumbatai samples tested in undisturbed conditions, and compacted condition at optimum moisture content, and then air dried. However, when compacted in the form of dry powder, as well as when compacted dry, mixed with different proportions of bentonite, this material showed swelling pressures with vapor transfer technique, as well as mixtures of bentonite with non-expansive material of Botucatu Formation. The absence of swell was explained by the slow damping provided by the vapor transfer that although promoting increasing dampen, did not sufficiently mobilized volume variation capable of transmitting blowing pressure. Therefore, the swell tests with the vapor transfer technique were effective to evaluate the swelling just in cases where clay minerals with swell potential were present in significant proportions.

Isolated granitic rock bodies (granites, granodiorites, quartz monzonites) in the vicinity of Benson in southeastern Arizona were studied to trace the behavior of rock weathering. Thin sections of fresh granites were examined to characterize the original mineralogy which consisted mainly of quartz, feldspars, and micas. The weathering products show up on the granites as grus and soil profiles as well as down slope in the basin deposits. X -ray diffraction studies of the < 2 micrometers fraction of the weathering products proved illite, smectite, illite-smectite mixed layer, and kaolinite to be the dominant clays; quartz and feldspar also persisted into this size fraction. Silt sized material produced similar results. The quartz monzonite of Texas Canyon afforded a special study of the initial weathering stages of feldspars and micas. In the < 2 micrometers fraction obtained from granitic material placed in an ultra sonic bath, the feldspars weathered to a Na-montmorillinite while biotite weathered to vermiculite.

Ce travail de thèse s’est inséré dans la problématique du stockage de déchets radioactifs en formation argileuse profonde. Il porte en particulier sur l’étude de la fissuration hydrique induite par la désaturation et resaturation de la roche en paroi des galeries de la station expérimentale de Tournemire (Averyon, France). Cette étude a visé à identifier les déterminismes microstructuraux et minéralogiques de la fissuration hydrique des argilites de Tournemire, en couplant au laboratoire la Corrélation d’Images Numériques (CIN) et la Microscopie Electronique à Balayage (MEB). Deux échantillons d’argilite de Tournemire ont été soumis à des variations d’humidités différentes par chocs et par paliers progressifs. La CIN a permis de mettre en évidence l’influence de l’humidité et de la teneur en eau sur l’amplitude de l’ouverture des fissures et des déformations à différentes échelles. Cette étude a également permis de mettre en lumière l’influence du chargement hydrique sur l’organisation des réseaux de fractures. Une cartographie minéralogique sur un champ plurimillimétrique en haute résolution a été également mise en œuvre au MEB sur ces deux échantillons d’argilites. Cette cartographie a permis d’apporter des données qualitatives et quantitatives sur l’anisotropie microstructurale et minéralogique de la roche argileuse et de proposer une estimation de la surface élémentaire représentative du système grain/matrice pour des zones à tendance argileuse.Le couplage de la CIN avec le MEB a révélé l’importance des hétérogénéités microstructurales relatives à la proportion, taille, élongation et orientation moyennes des inclusions rigides présentes dans la matrice argileuse de la roche, sur la localisation des fissures hydriques<br>This study is included in the issues of a nuclear waste storage in deep geological clay formations. It concerns the cracking phenomenon due to desaturation and saturation processes of the argillaceous medium on gallery walls of the Underground Laboratory of Tournemire (Aveyron, France). The work presented here aims to identify in laboratory the different mineralogical factors which control the cracking generated by humidity variations, coupling two methods: the Digital Image Correlation (DIC) and the Scanning Electron Microscopy (SEM).Two clay rock samples were submitted to swelling/shrinkage processes by fast bumps or gradual humidity variations. The DIC method enabled to reveal the influence of humidity and water content on crack widths and deformations intensity to different scales. This study highlighted the part of humidity variations on evolution and width of crack networks while comparing the results obtained by different conditions of humidity variations.A mineralogical map was investigated on a millimeter field with high resolution on two clay rock samples. It allowed to: quantify the microstructural anisotropy of the rock, and estimate the size of a representative elementary surface of a microstructural system composed of coarse grains and clay matrix, for argillaceous areas.The DIC-SEM approach has shown the closed relation between the location of microstructural heterogeneities such as local proportion of coarse grains and clay matrix, medium size, length ratio and orientation of coarse grains, with the position of the hydric cracks

Le Sud du Brésil est une région où l'agriculture est très intensive et la pression sur les sols est beaucoup plus importante que dans la région amazonienne. Ainsi, il est important d'étudier les processus d'altération des roches qui constituent des étapes clés du développement des sols et de leurs fonctions environnementales.Dans ce contexte, ce travail vise à : (i) caractériser la morphologie, les propriétés physiques et chimiques de profils d'altération développés en l'absence ou avec une intervention humaine minimale : (ii) établir les évolutions géochimiques et minéralogiques des sols dans un environnement subtropical ; et (iii) évaluer l'impact des actions anthropiques sur la minéralogie des horizons de surface. Cette étude concerne des sols du Rio Grande do Sul dont le climat subtropical (T ~17°C et P ~1800 mm/an) favorise l'accumulation de matière organique ainsi que la formation de minéraux argileux 2:1 en faible proportion. Les indices d'altération (Weathering Intensity Scale – WIS, Chemical Index of Alteration - CIA) permettent de classer les profils selon leur degré d'altération et de leur composition minéralogique différente (smectite, smectite + kaolinite, kaolinite). Dans la dernière partie les résultats montrent qu'après 12 ans de culture des sols avec un système intégré culture-élevage les surfaces non pâturées présentent une proportion moins importante de minéraux 2:1. Les surfaces sous pâturage intensif et modéré présentent une aluminisation plus élevée de la couche interfoliaire des minéraux 2:1. La fixation d'une partie de l'aluminium dans la phase solide du sol, ce qui pourrait le rendre moins disponible pour les plantes et diminuer sa phytotoxicité<br>Southern Brazil is a region with a very intensive agriculture and the pressure on soil is considerably more intense than in the Amazonian region. Thus, it is necessary to study weathering processes as they control soil development and their environmental functions.In this context, this work aims to: (i) characterize the morphological, physical and chemical properties of weathering profiles developed in the absence, or with minimal human action; (ii) establish the geochemical and mineralogical evolution of soils in a subtropical environment; and (iii) assess the impact of anthropogenic actions on on the mineralogy of surface horizons. This study concerns soils of Rio Grande do Sul where the subtropical climate (T ~17°C and P ~1800mm/yr) favored the accumulation of organic matter and occurrence of 2:1 clay minerals in low proportion. The weathering indices (Weathering Intensity Scale - WIS and Chemical Index of Alteration - CIA) make it possible to classify the profiles according to their weathering intensity and their different mineralogical compositions (smectite, smectite + kaolinite, kaolinite).In the last chapter, the results show that after 12 years of cultivation under an integrated soybean–beef cattle production system, the ungrazed areas presented lower proportion of 2:1 minerals. The areas under intensive grazing and moderate grazing presented higher aluminization of the interlayer of 2:1 minerals. The higher aluminization under intensive and moderate grazing managements may be a drain of aluminum in the soil solid phase and possibly making it less available to plants and decreasing its phytotoxicity<br>O sul do Brasil é uma região com uma agricultura muito intensa e com grande pressão de uso do solo, consideravelmente mais intenso do que na região da Amazônia. Assim, é necessário desenvolver estudos que relacionem o desenvolvimento do solo com seu respectivo material de origem, detalhando as transformações na zona de transição solo-rocha e suas implicações para as atividades ambientais e humanas. Neste contexto, este trabalho tem como objetivo: (i) caracterizar os aspectos mineralógicos, pedoquimicos e geoquimicos dos perfis de alteração desenvolvidos na ausência ou mínima ação humana; (ii) caracterizar qualitativa e semi-quantitativamente os minerais primários e os minerais pedogênicos em solos inseridos em regiões ecossistêmicas importantes do Rio Grande do Sul; e (iii) avaliar o impacto de diferentes intensidades de pastejo na mineralogia de um Latossolo, sob sistema de produção integrada soja-bovinos de corte no sul do Brasil. Este estudo foi realizado em solos do Rio Grande do Sul, onde o clima subtropical (temperatura média anual ~ 17°C, precipitação anual média de 1800mm/ano) favorece o acúmulo de matéria orgânica ea ocorrência de argilominerais 2:1.Os índices de intemperismo (Weathering Intensity Scale - WIS e Chemical Index of Alteration - CIA), considerando a composição mineralógica dos perfis de alteração, indicaram a seguinte sequência crescente do grau de intemperismo: esmectita &lt; caulinita - esmectita &lt; caulinita. O estudo mostrou diferenças importantes nos solos, mesmo entre aqueles formados a partir do mesmo material de origem, devido às diferenças climáticas e de relevo. Por fim, após 12 anos sob um sistema integrado de produção de soja-bovinos de corte, as áreas não pastejadas apresentaram menor intensidade para os argilominerais 2:1. Por outro lado, as áreas sob pastejo intensivo e pastejo moderado apresentaram comportamento semelhante, devido à maior aluminização da entrecamada dos argilominerais 2:1. A maior aluminização sob pastejo intensivo e moderado pode ser um dreno de alumínio na fase sólida do solo, tornando-o menos disponível para as plantas e diminuindo sua fitotoxicidade