Dissertations / Theses on the topic 'Concrete box'

Post-tensioned segmental concrete box girders have been in use in the United States since the early 1970s. This unique bridge system uses post-tensioning to connect many smaller concrete bridge segments into very efficient long span bridges. However, because of the slender components, localized transverse bending becomes more critical when compared to more conventional bridge types. Bridge owners are finding that ratings for standard loads and permit trucks are often controlled by the transverse behavior of the girders near concentrated wheel loads. The popular analysis methods used today range from two dimensional frame models to three dimensional finite element models of the entire bridge. Currently, engineers must make sound engineering judgments on limited available information, while balancing safety and economy.

To quantify and understand longitudinal and transverse behavior, the results from three live load tests of single cell segmental concrete box girder bridges are presented. Each bridge was instrumented with longitudinal and transverse strain sensors on at least two cross sections as well as rotation and deflection sensors, when possible. Two dimensional transverse frame models and three dimensional shell models were compared to the test results for each subject bridge. The two dimensional frame analyses using the common bottom web pin and roller boundary conditions provide mean absolute percent error in excess of 250%. Conversely, the newly introduced boundary conditions using pin supports at the top and bottom of each web was shown to reduce mean absolute percent error to 82%, which is on the same order of magnitude as longitudinal beamline analysis.

The three dimensional shell models were insensitive to several changes including mesh fineness, number of spans modeled, and support conditions. Using uniform surface loading, the transverse modeling procedure was shown to provide significantly more accurate results than the common two dimensional frame models. A faster and more convenient analysis method using a program generated, structure specific, influence surface was also outlined. This method produced similar results when compared to the uniform surface loading method, while allowing additional automation for easier load application.

Ph. D.

Thesis (Ph. D.)--University of California, San Diego, 2009.
Title from first page of PDF file (viewed July 2, 2009). Available via ProQuest Digital Dissertations. Vita. Includes bibliographical references (p. 341-345).

Bridges are important and efficient structures which are comprised of a number of elements and substructures, namely the deck, abutment and foundation and possibly additional intermediate supports. Recently the horizontally curved box girder bridge has become more desirable in modern motorway systems and big cities. Even though numerous amounts of research have been in progress to analyse and understand the behaviour of all types of box-girder bridges, the results from these different research projects are unevaluated and dispersed. Therefore, a clear understanding of an accurate study on straight and curved box-girder bridges is needed. In this study, a three dimensional straight and horizontally curved prestressed box section has been analysed with shell elements using the finite element analysis program ANSYS to examine structural behaviour and load carrying capacity. The box girder under static gravity, pre-stressed and gravity + pre-stressed loading has been analysed. The model which has been investigated in this report is taken from a published paper and expanded to study the effects of curvature under different loads applied (UDLs). The report concludes that the FEA using shell elements is able to predict the behaviour of box girders with adequate accuracy through the comparisons made between stress results from analytical hand calculations and published work, both for the straight and curved box girder bridges. Further theoretical and analytical investigations have been carried out to study the effects of parameters such as horizontal curvature, prestressing, and traffic patterning. For this purpose, a new model was created, modelled with an accurate prestress representation and analysed as a three-dimensional model using the ANSYS. This thesis presents a complete description of the bridge system, addressing the aforementioned parameters and presenting the results through graphs of stress distribution, and displacement. Recommendations for the practical use of FE for bridge design are discussed.

Master of Science
Department of Civil Engineering
Robert J. Peterman
Concrete box culvert floor slabs are known to have detrimental effects on river and stream hydraulics. Consequences include an aquatic environment less friendly to the passage of fish and other organisms. This has prompted environmental regulations restricting construction of traditional, four-sided box culvert structures in rivers and streams populated by protected species. The box culvert standard currently used by the Kansas Department of Transportation (KDOT) is likely to receive increased scrutiny from federal and state environmental regulators in the near future. Additionally, multiple-cell box culverts present a maintenance challenge, since passing driftwood and debris are frequently caught in the barrels and around cell walls. As more structures reach the end of their design lives, new solutions must be developed to facilitate a more suitable replacement. Since construction can cause significant delays to the traveling public, systems and techniques which accelerate the construction process should also be considered. This thesis documents development of a single-span replacement system for box culverts in the state of Kansas. Solutions were found using either a flab slab or the center span of the KDOT three-span, haunched-slab bridge standard. In both cases, the concrete superstructure is connected monolithically with a set of abutment walls, which sit on piling. The system provides an undisturbed, natural channel bottom, satisfying environmental regulations. Important structural, construction, maintenance, and economic criteria considered during the planning stages of bridge design are discussed. While both superstructural systems were found to perform acceptably, the haunched section was chosen for preliminary design. Rationale for selection of this system is explained. Structural modeling, analysis, and design data are presented to demonstrate viability of the system for spans ranging from 32 to 72 feet. The new system is expected to meet KDOT’s needs for structural, environmental, and hydraulic performance, as well as long-term durability. Another option involving accelerated bridge construction (ABC) practices is discussed.

This thesis discusses the development of a new type of fibre-reinforced polymer (FRP) beam for use in civil engineering systems. After a detailed evaluation of the advantages and disadvantages of current FRP beam technology, a different approach is proposed which combines traditional laminates with a novel casting technique. To pre-dimension the beam, the classical beam theory is adapted to allow for FRP materials. The resulting formulae were used to determine critical parameters, such as laminate thickness and location in the cross-section, and core dimensions, and to identify failure modes. Based on the results of this analytical study, a detailed testing program was developed. In addition to classical tests, such as bending, shear, and lateral torsion, the performance of the beam was also examined under particular loading regimes specifically designed to induce local failure modes, such as buckling of the web and bearing failure of the section under concentrated loads. The experimental results revealed very good agreement with the analytical predictions. These results were corroborated by a detailed non-linear finite-element analysis, including core cracking and laminate damage. This analysis, in particular, highlighted the synergy between bending and shear behaviour of the beam. This study has revealed that this new type of FRP beam behaves in a predictable manner. Furthermore, the experimental results verified that the cross-section, which combines traditional laminates with cast polymer concrete, did not suffer from many of the disadvantages identified in current FRP beams. The cracking of the polymer concrete under shear, however, does cause the beam to fail prior to the laminates reaching their ultimate shear stress.

Reinforced Concrete Box Culverts (RCBCs) are an integral part of the national and international transportation infrastructure. The National Bridge Inventory Standards (NBIS) requires that all bridges, which include culverts with spans ≥ 20 ft. (6.1 m), be load rated for safe load carrying capacity in accordance with the AASHTO Manual for Bridge Evaluation (MBE). In Kentucky, the Transportation Cabinet manages more than 15,500 bridges, of which almost 1,400 are bridge size culverts. Of the 1241 bridge size RCBCs that were being evaluated in Kentucky between 2015 and 2018, 846 were 2-cell culverts (or 68%). The objective in this study is to evaluate 2-cell RCBCs using the finite element (FE) method and to propose dead load and live load demand equations that can be used to determine the capacity demand ratio (C/D) and the load rating. The results indicate that the maximum dead load forces (positive and negative moments, and shear) vary linearly with respect to an increase in fill height, while the variation is bi-linear for the maximum live load forces. The proposed equations are derived in terms of the clear span and fill height. The results also indicated that, for fill heights greater than 10 ft (3 m), the maximum live load positive bending moments are less than 10% of their dead load counterparts. The primary advantage of the proposed equations lies in their simple formulation when analyzing and designing 2-cell culverts, which in turn alleviates the need to conduct a detailed finite element analysis to determine the maximum forces in 2-cell RCBCs.

Self-compacting concrete (SCC) can flow into place and compact under its own weight into a uniform mass even areas of congested reinforcement. Compared to vibrated concrete (VC), SCC has enhanced qualities and improves the durability of concrete, productivity and working conditions due to elimination of external vibration. Although SCC has passed from the research phase into real application, the need to update the knowledge on the fresh and hardened characteristics of SCC increases to overcome the problems associated with such concrete and to improve its performance. The research reported in this thesis divided into three parts. The first part concerns the proportioning of SCC mixes, a simple and rational mix design procedure based on the desired target plastic viscosity and compressive strength of the mix has been developed. Practical guidelines in the form of design charts are provided for choosing the mix proportions of SCC mixes. An extensive experimental program was carried out in order to provide experimental validation of this mix design procedure on a series of SCC mixes in both the fresh and hardened states. All these mixes were extensively tested in the fresh state using the slump cone, J–ring, L–box and V–funnel apparatus; and these tests proved conclusively the validity of the mix proportioning method in the sense that all the mixes satisfied the self–compacting criteria and achieved the desired target plastic viscosity and compressive strength. In the second part of the thesis, the fracture properties of the SCC mixes have been determined. These mixes differ by coarse aggregate volume (CA), paste to solids ratios (p/s) and water to cementitious material (w/cm). The simplified boundary effect approach (SBE) and the non-linear fictitious crack model are used to determine the size-independent fracture energy.

In order to more accurately quantify the behavior and degradation of bridges throughout their service life, the Federal Highway Administration lunched the Long-Term Bridge Performance Program. As part of this program an I-girder, integral abutment bridge near Perry, Utah and a two span, box-girder bridge south of Sacramento, California were instrumented with foil strain gauges, velocity transducers, vibrating wire strain gauges, thermocouples, and tiltmeters. In this research study, data from the thermocouples was used to calculate average bridge temperature and compare it to the recommended design criteria in accordance to the 2010 LRFD Bridge Design Specifications of the American Association of State Highway and Transportation Officials (AASHTO). The design maximum average bridge temperature defined in the 2010 LRFD Bridge Design Specifications was exceeded for both bridges. The accuracy of the 1991 Kuppa Method and the 1976 Black and Emerson Method to estimate the average bridge temperature based on ambient temperature was studied and a new method that was found to be more accurate was proposed. Long-term predictions of average bridge temperature for both bridges were calculated. Temperature gradients were measured and compared to the 2010 AASHTO LRFD Bridge Design Specifications and the 1978 Priestley Method. Calculated flexural stresses as a function of maximum positive and negative temperature gradients were found to exceed the service limit state established in the 2010 AASHTO LRFD Bridge Design Specifications in the case of the California bridge.

The scheduled replacement of the 8th North Bridge, in Salt Lake City, UT, presented a unique opportunity to test a pre-cast concrete deck, steel girder bridge. A live-load test was performed under the directions of Bridge Diagnostic Inc (BDI) and Utah State University. Six different load paths were chosen to be tested. The recorded data was used to calibrate a finite-element model of this superstructure, which was created using solid, shell, and frame elements. A comparison between the measured and finite-element response was performed and it was determined that the finite-element model replicated the measured results within 3.5% of the actual values. This model was later used to obtain theoretical live-load distribution factors, which were compared with the AASHTO LRFD Specifications estimations. The analysis was performed for the actual condition of the bridge and the original case of the bridge, which included sidewalks on both sides. The comparison showed that the code over predicted the behavior of the actual structure by 10%. For the original case, the code's estimation differed by as much as 45% of the theoretical values. Another opportunity was presented to test the behavior of a cast-in-place concrete box girder bridge in Joaquin County, CA. The Walnut Grove Bridge was tested by BDI at the request of Utah State University. The test was performed with six different load paths and the recorded data was used to calibrate a finite-element model of the structure. The bridge was modeled using shell elements and the supports were modeled using solid elements. The model was shown to replicate the actual behavior of the bridge to within 3% of the measured values. The calibrated model was then used to calculate the theoretical live-load distribution factors, which allowed a comparison of the results with the AASHTOO LRFD Specifications equations. This analysis was performed for the real conditions of the bridge and a second case where intermediate diaphragms were not included. It was determined that the code's equations estimated the behavior of the interior girder more accurately for the second model (within 10%) than the real model of the bridge (within 20%).

[EN] Bridges, as an important component of infrastructure, are expected to meet all the requirements for a modern society. Traditionally, the primary aim in bridge design has been to achieve the lowest cost while guaranteeing the structural efficiency. However, concerns regarding building a more sustainable future have change the priorities of society. Ecological and durable structures are increasingly demanded. Under these premises, heuristic optimization methods provide an effective alternative to structural designs based on experience. The emergence of new materials, structural designs and sustainable criteria motivate the need to create a methodology for the automatic and accurate design of a real post-tensioned concrete bridge that considers all these aspects. For the first time, this thesis studies the efficient design of post-tensioned concrete box-girder road bridges from a sustainable point of view. This research integrates environmental, safety and durability criteria into the optimum design of the bridge. The methodology proposed provides multiple trade-off solutions that hardly increase the cost and achieve improved safety and durability. Likewise, this approach quantifies the sustainable criteria in economic terms, and evaluates the effect of these criteria on the best values of the variables. In this context, a multi-objective optimization is formulated to provide multiple trade-off and high-performing solutions that balance economic, ecologic and societal goals. An optimization design program selects the best geometry, concrete type, reinforcement and post-tensioning steel that meet the objectives selected. A three-span continuous box-girder road bridge located in a coastal region is selected for a case study. This approach provides vital knowledge about this type of bridge in the sustainable context. The life-cycle perspective has been included through a lifetime performance evaluation that models the bridge deterioration process due to chloride-induced corrosion. The economic, environmental and societal impacts of maintenance actions required to extend the service life are examined. Therefore, the proposed goals for an efficient design have been switch from initial stage to life-cycle consideration. Faced with the large computational time of multi-objective optimization and finite-element analysis, artificial neural networks (ANNs) are integrated in the proposed methodology. ANNs are trained to predict the structural response based on the design variables, without the need to analyze the bridge response. The multi-objective optimization problem results in a set of trade-off solutions characterized by the presence of conflicting objectives. The final selection of preferred solutions is simplified by a decision-making technique. A rational technique converts a verbal pairwise comparison between criteria with a degree of uncertainty into numerical values that guarantee the consistency of judgments. This thesis gives a guide for the sustainable design of concrete structures. The use of the proposed approach leads to designs with lower life-cycle cost and emissions compared to general design approaches. Both bridge safety and durability can be improved with a little cost increment by choosing the correct design variables. In addition, this methodology is applicable to any type of structure and material.
[ES] Los puentes, como parte importante de una infraestructura, se espera que reúnan todos los requisitos de una sociedad moderna. Tradicionalmente, el objetivo principal en el diseño de puentes ha sido lograr el menor coste mientras se garantiza la eficiencia estructural. Sin embargo, la preocupación por construir un futuro más sostenible ha provocado un cambio en las prioridades de la sociedad. Estructuras más ecológicas y duraderas son cada vez más demandadas. Bajo estas premisas, los métodos de optimización heurística proporcionan una alternativa eficaz a los diseños estructurales basados en la experiencia. La aparición de nuevos materiales, diseños estructurales y criterios sostenibles motivan la necesidad de crear una metodología para el diseño automático y preciso de un puente real de hormigón postesado que considere todos estos aspectos. Por primera vez, esta tesis estudia el diseño eficiente de puentes de hormigón postesado con sección en cajón desde un punto de vista sostenible. Esta investigación integra criterios ambientales, de seguridad estructural y durabilidad en el diseño óptimo del puente. La metodología propuesta proporciona múltiples soluciones que apenas encarecen el coste y mejoran la seguridad y durabilidad. Al mismo tiempo, se cuantifica el enfoque sostenible en términos económicos, y se evalúa el efecto que tienen dichos criterios en el valor óptimo de las variables. En este contexto, se formula una optimización multiobjetivo que proporciona soluciones eficientes y de compromiso entre los criterios económicos, ecológicos y sociales. Un programa de optimización del diseño selecciona la mejor combinación de geometría, tipo de hormigón, armadura y postesado que cumpla con los objetivos seleccionados. Se ha escogido como caso de estudio un puente continuo en cajón de tres vanos situado en la costa. Este método proporciona un mayor conocimiento sobre esta tipología de puentes desde un punto de vista sostenible. Se ha estudiado el ciclo de vida a través de la evaluación del deterioro estructural del puente debido al ataque por cloruros. Se examina el impacto económico, ambiental y social que produce el mantenimiento necesario para extender la vida útil del puente. Por lo tanto, los objetivos propuestos para un diseño eficiente han sido trasladados desde la etapa inicial hasta la consideración del ciclo de vida. Para solucionar el problema del elevado tiempo de cálculo debido a la optimización multiobjetivo y el análisis por elementos finitos, se han integrado redes neuronales en la metodología propuesta. Las redes neuronales son entrenadas para predecir la respuesta estructural a partir de las variables de diseño, sin la necesidad de analizar el puente. El problema de optimización multiobjetivo se traduce en un conjunto de soluciones de compromiso que representan objetivos contrapuestos. La selección final de las soluciones preferidas se simplifica mediante una técnica de toma de decisiones. Una técnica estructurada convierte los juicios basados en comparaciones por pares de elementos con un grado de incertidumbre en valores numéricos que garantizan la consistencia de dichos juicios. Esta tesis proporciona una guía que extiende y mejora las recomendaciones sobre el diseño de estructuras de hormigón dentro del contexto de desarrollo sostenible. El uso de la metodología propuesta lleva a diseños con menor coste y emisiones del ciclo de vida, comparado con diseños que siguen metodologías generales. Los resultados demuestran que mediante una correcta elección del valor de las variables se puede mejorar la seguridad y durabilidad del puente con un pequeño incremento del coste. Además, esta metodología es aplicable a cualquier tipo de estructura y material.
[CAT] Els ponts, com a part important d'una infraestructura, s'espera que reunisquen tots els requisits d'una societat moderna. Tradicionalment, l'objectiu principal en el disseny de ponts ha sigut aconseguir el menor cost mentres es garantix l'eficiència estructural. No obstant això, la preocupació per construir un futur més sostenible ha provocat un canvi en les prioritats de la societat. Estructures més ecològiques i durables són cada vegada més demandades. Davall estes premisses, els mètodes d'optimització heurística proporcionen una alternativa eficaç als dissenys estructurals basats en l'experiència. L'aparició de nous materials, dissenys estructurals i criteris sostenibles motiven la necessitat de crear una metodologia per al disseny automàtic i precís d'un pont real de formigó posttesat que considere tots estos aspectos. Per primera vegada, esta tesi estudia el disseny eficient de ponts de formigó posttesat amb secció en calaix des d'un punt de vista sostenible. Esta investigació integra criteris ambientals, de seguretat estructural i durabilitat en el disseny òptim del pont. La metodologia proposada proporciona múltiples solucions que a penes encarixen el cost i milloren la seguretat i durabilitat. Al mateix temps, es quantifica l'enfocament sostenible en termes econòmics, i s'avalua l'efecte que tenen els dits criteris en el valor òptim de les variables. En este context, es formula una optimització multiobjetivo que proporciona solucions eficients i de compromís entre els criteris econòmics, ecològics i socials. Un programa d'optimització del disseny selecciona la millor geometria, tipus de formigó, armadura i posttesat que complisquen amb els objectius seleccionats. S'ha triat com a cas d'estudi un pont continu en calaix de tres vans situat en la costa. Este mètode proporciona un major coneixement sobre esta tipologia de ponts des d'un punt de vista sostenible. S'ha estudiat el cicle de vida a través de l'avaluació del deteriorament estructural del pont a causa de l'atac per clorurs. S'examina l'impacte econòmic, ambiental i social que produïx el manteniment necessari per a estendre la vida útil del pont. Per tant, els objectius proposats per a un disseny eficient han sigut traslladats des de l'etapa inicial fins a la consideració del cicle de vida. Per a solucionar el problema de l'elevat temps de càlcul degut a l'optimització multiobjetivo i l'anàlisi per elements finits, s'han integrat xarxes neuronals en la metodologia proposada. Les xarxes neuronals són entrenades per a predir la resposta estructural a partir de les variables de disseny, sense la necessitat d'analitzar el pont. El problema d'optimització multiobjetivo es traduïx en un conjunt de solucions de compromís que representen objectius contraposats. La selecció final de les solucions preferides se simplifica per mitjà d'una tècnica de presa de decisions. Una tècnica estructurada convertix els juís basats en comparacions per parells d'elements amb un grau d'incertesa en valors numèrics que garantixen la consistència dels dits juís. Esta tesi proporciona una guia que estén i millora les recomanacions sobre el disseny d'estructures de formigó dins del context de desenrotllament sostenible. L'ús de la metodologia proposada porta a dissenys amb menor cost i emissions del cicle de vida, comparat amb dissenys que seguixen metodologies generals. Els resultats demostren que per mitjà d'una correcta elecció del valor de les variables es pot millorar la seguretat i durabilitat del pont amb un xicotet increment del cost. A més, esta metodologia és aplicable a qualsevol tipus d'estructura i material.
García Segura, T. (2016). Efficient design of post-tensioned concrete box-girder road bridges based on sustainable multi-objective criteria [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/73147
TESIS

When designing a bridge it is of high importance that the geometry for the cross section is optimized for the structure. This is partly due to the influence of the amount of material needed and its impact on the budget and environment. The influence of choosing the right amount of each material lies in the unit-price of the different material, where they can differ significantly. The Swedish Transport Administration, Trafikverket, has ordered the construction of Stockholm Bypass which is one of Swedens largest infrastructure project and is valued to 27.6 billion SEK according to the price index of the year 2009. The infrastructure project is divided into multiple projects where one of them is assigned to Implenia and Veidekke through a joint venture (Joint venture Hjulsta, JVH) and is valued to nearly 800 MSEK. The reference bridge that is used in the analysis of the master’s thesis is a part of the project. The aim of this masters thesis was to analyze and compare the two construction methods, mov- able scaffolding system (MSS) and incremental launching for the reference bridge with respect to amount post-tensioning and slenderness. Furthermore, an economical comparison between the two construction methods was carried out based on the obtained results. The analysis of the MSS was carried out by modeling the reference bridge structure in the finite element software SOFiSTiK AG. The bridge was modeled with different cross section height, i.e. different slenderness where the optimal amount of post-tension tendons could be determined by iteration until stress conditions from the Eurocode were fulfilled. For the incremental launching method, a numerical analysis was performed. The optimal amount of required post-tensioning was evaluated in the construction stages and final stages with different construction heights i.e. different values of slenderness. A cost analysis was also performed where the aim was to analyze how the total cost of the construc- tion of the bridge would be influenced by the different slenderness of the bridge as a comparison for the two construction methods. This was done by dividing the costs into fixed costs and variable costs. The results showed that the structural rigidity had a large influence on the required amount of prestressing steel for both construction methods. In other words, the smaller the cross section the more prestressing steel was required. Incremental launching proved to require a much greater amount of (PT) tendons compared to the MSS although the identical cross sections and properties for both methods, except for the PT. The prestressing for incremental launching is generally by centrical prestressing during the construction stages. A intersection point was obtained in the cost analysis for the construction methods. The incremental launching was the cheaper solution for slenderness smaller than the intersection point at slenderness between 17 and 18. The MSS was cheaper than the incremental launching for slenderness larger than the intersection point.
Vid dimensionering av tvärsektioner i broar är det av stor vikt att optimera geometrin avseende materialåtgång då mängden material har stor på verkan på ett projekts budget samt miljö. Eftersom konstruktioner ofta består av olika byggnadsmaterial gäller det vid optimering att välja byggnadsmaterialen genom optimerad proportionalitet. Förbifart Stockholm, beställt av Trafikverket, är ett av Sveriges största infrastrukturprojekt och värderas till 27,6 miljarder kronor enligt 2009 års prisnivå. Infrastrukturprojektet är uppdelat i flera mindre entreprenader eller så kallade etapper. Den entreprenad som omfattar trafikplats Hjulsta Södra har blivit tilldelat till Implenia och Veidekke genom ett konsortium (Jointventure Hjulsta, JVH) och värderas till cirka 800 miljoner kronor. Den förspända betongbro som byggs i trafikplats Hjulsta ligger till grund för analysen i detta examensarbete och har använts som referens under vår studie. Syftet med examensarbete var att analysera och jämföra två de två olika produktionsmetoderna, Movable scaffolding system (MSS) och etappvis lansering med hänsyn till erforderlig mängd förspänningskablar och slankhet. Vidare, baserat på erhållna resultat, utfördes en ekonomisk analys och jämförelse mellan produktionsmetoderna. Analysen av MSS utfördes genom att modellera brokonstruktionen i mjukvaruprogrammet SOFiSTiK AG som bygger på finita elementmetoder. Konstruktionen modellerades för olika slankheter, där slankheten definieras som kvoten mellan maximala spannlängden och brons tvärsnittshöjd. Spannlängden hölls konstant medan tvärsnittshöjden varierade för att erhålla olika slankheter. Den optimala slankheten bestämdes genom iterering av mängd förspänningskablar tills spänningsvillkoren var uppfyllda enligt Eurocode. För analysen av etappvis lansering utfördes en numerisk analys vars den optimala mängden förspänningskablar utvärderades i byggskedet (construction stages) samt i slutskedet (final stage). Analysen utfördes på samma sätt för de olika slankheterna. Slutligen genomfördes en konstandsanalys för de olika metoderna. Syftet var att jämföra hur den totala kostnaden för uppförandet av brokonstruktionen skiljde sig för de olika slankheterna. Jämförelsen genomfördes genom att dela upp de olika kostnaderna i fasta kostnader samt rörliga kostnader. Resultaten från analysen visade att den erforderliga mängd förspänningskablar som behövs i en förspänd betongbro är beroende av den strukturella styvheten i tvärsektionen. En högre slankhet, alltså lägre tvärsnittshöjd, ger lägre styvhet och därav mer erforderlig förspänningskablar. Etappvis lansering visade sig vara den metod som krävde mer mängd förspänningskablar. I resultaten för kostnadsanalysen uppmättes en skärningspunkt, för en slankhet mellan 17-18, mellan de två olika metoderna. För förspända betongbroar med slankhet lägre än skärningsupunkten vid 17-18 är etappvis lansering det billigare alternativet. För slankheter högre än 17-18 är MSS det mer ekonomiskt lönsamma alternativet.

Master of Science
Department of Civil Engineering
Hayder A. Rasheed
The Kansas Department of Transportation’s (KDOT) Bridge 059-045 is a reinforced concrete box girder bridge constructed in 1965 to connect the rural Shawnee Drive across Interstate 135 near McPhearson, Kansas, in between Salina and Wichita. The bridge was observed, during an annual inspection in 1998, to have experienced some settlement, which was further found to be due to its proximity to a sinkhole. This settlement progressed to noticeable levels in 2012 necessitating a semi-annual elevation profile survey that was consistently conducted by KDOT. In April 2016, KDOT determined that the bridge required a detailed finite element analysis to determine the safety and suitability of the bridge to stay open to traffic. Accordingly, a two-level Finite Element Analysis was performed using RISA 3D and Abaqus to assess the level of distress in the bridge due to the continuous differential settlement as a result of the active sinkhole deep in the soil under the bridge. The force-moment results were taken from the RISA 3D model for further analysis of various structural components that make up the bridge, including the box girder, piers, and piles. The stress distribution results from the Abaqus model were investigated for the same components of the bridge. A strengthening design scheme using near surface mounted fiber reinforced polymer rebar was developed to extend the service life of the bridge.

Objective condition assessment is essential to make better decisions for safety and serviceability of existing civil infrastructure systems. This study explores the condition of an existing transit guideway system that has been in service for thirty-five years. The structural system is composed of six-span continuous prestressed concrete bridge segments. The overall transit system incorporates a number of continuous bridges which share common design details, geometries, and loading conditions. The original analysis is based on certain simplifying assumptions such as rigid behavior over supports and simplified tendon/concrete/steel plate interaction. The current objective is to conduct a representative study for a more accurate understanding of the structural system and its behavior. The scope of the study is to generate finite element models (FEMs) to be used in static and dynamic parameter sensitivity studies, as well load rating and reliability analysis of the structure. The FEMs are used for eigenvalue analysis and simulations. Parameter sensitivity studies consider the effect of changing critical parameters, including material properties, prestress loss, and boundary and continuity conditions, on the static and dynamic structural response. Load ratings are developed using an American Association for State Highway Transportation Officials Load and Resistance Factor Rating (AASHTO LRFR) approach. The reliability of the structural system is evaluated based on the data obtained from various finite element models. Recommendations for experimental validation of the FEM are presented. This study is expected to provide information to make better decisions for operations, maintenance and safety requirements; to be a benchmark for future studies, to establish a procedure and methodology for structural condition assessment, and to contribute to the general research body of knowledge in condition assessment and structural health monitoring.
M.S.
Department of Civil and Environmental Engineering
Engineering and Computer Science
Civil Engineering

The subject of this diploma thesis is the design and analysis of a bridge at the R48 bypass over the Ostravica River. For this purpose, three variants of the supporting structure solution were developed from which a variant of additionally prestressed chamber girder with perpendicular walls was selected. The main task is to assess the construction for phased construction. The static calculation was drawn up according to European

O emprego de pilares mistos formados por tubos de aço preenchidos com concreto de alta resistência, sobretudo em edifícios altos, é uma tendência em diversos países europeus, americanos e asiáticos. A tais elementos são atribuídas vantagens como: alta resistência e ductilidade, economia de materiais e mão-de-obra, redução das dimensões da seção transversal e melhoria no comportamento dos materiais aço e concreto, devido ao efeito de confinamento. Buscando suprir algumas carências de conhecimento, procura-se obter dados experimentais sobre o comportamento de pilares mistos axialmente comprimidos, possibilitando desta forma avaliar parâmetros como influência da forma da seção transversal e da espessura do perfil tubular no seu comportamento. Foram analisadas seções quadradas, circulares e retangulares, preenchidas por concreto com resistência média de 50MPa. A ruína destes elementos caracterizou-se pelo esmagamento do concreto, ocorrendo posteriormente a flambagem local do perfil em diversos pontos. A capacidade resistente prevista por diversas normas resultou em valores muito próximos dos experimentais, embora várias destas normas não considerem o efeito de confinamento. Os ensaios mostraram que o efeito de confinamento contribui de forma decisiva na melhoria do comportamento dos materiais, sobretudo ductilizando o concreto de alta resistência, entretanto seus efeitos não são significativos no aumento da capacidade resistente da seção mista. Alguns critérios para avaliação da ductilidade à compressão foram adaptados e mostraram bons resultados, possibilitando o cálculo do índice de ductilidade.
The use of concrete filled steel tubes especially in tall buildings is a tendency in several european, american and asian countries. The use of these members has several advantages: high resistance and ductility, saving of materials and labour, reduction of cross section dimensions and improvement in behaviour of the materials steel and concrete due the confinement. The main purpose of this study is provide some experimental results of the behaviour of concrete filled steel tubes concentrically loaded. The main experimental parameters considered were the influence of the cross-section shape and thickness of steel tube. Square, circular and rectangular cross-section shapes infilling with concrete of the 50MPa of strength were analyzed. The failure was characterized for crushing of the concrete and later local buckling of the steel section in several points. The strength capacity predicted for several standards showed good agreement with the experimental failure values although this does not consider the confinement of the concrete. The results of tests showed that the confinement effect contributes for improvement behaviour of materials, especially increasing the ductility of the high strength concrete. However the results showed that the triaxial confinement does not increase the axial capacity of the concrete filled steel tubes. Some methods to estimate the ductility of axially compressed concrete columns were adapted and showed good results permitting the calculation of the ductility index of short columns.

Il calcolo delle sollecitazioni negli impalcati a cassone monocellulare è abbastanza semplice qualora si utilizzi un programma di calcolo, ma è assai più complesso capire i meccanismi fisici con cui si sviluppano. Infatti, questi impalcati sono dotati di diaframmi di irrigidimento solamente in corrispondenza delle spalle e delle pile. L’assenza dei diaframmi in campata non consente di ritenere queste sezioni trasversalmente rigide, come richiesto dalla teoria classica di DSV. Quindi si rende necessario considerare deformabile la sezione nel proprio piano e considerare tutti gli effetti prodotti dalla perdita di forma. Infatti, per condizioni di carico antisimmetriche i nodi della sezione trasversale possono subire spostamenti relativi, quindi la sezione si distorce, facendo nascere sollecitazioni trasversali e longitudinali aggiuntive. Il lavoro si pone l’obiettivo di studiare in modo approfondito il fenomeno fisico cui sono soggetti questi tipi di impalcati. In un primo momento studiando, in maniera molto dettagliata, la teoria analitica che ci permette di comprendere l’interazione che nasce tra la direzione trasversale e longitudinale dimostrando e ricostruendo alcuni passaggi analitici fondamentali. Inoltre attraverso quest’approccio prettamente teorico si vuole quantificare ogni singolo contributo prodotto dal comportamento fisico dell’impalcato, realizzando anche dei modelli numerici con software FEM di confronto. Al fine di capire l’influenza della distorsione della sezione, associata al caricamento antisimmetrico, che caratterizza questi tipi d’impalcati, si conduce un’analisi di sensitività variando la capacità di distorcersi della sezione. Inoltre si conduce uno studio parametrico finalizzato alla ricerca di un metodo di progettazione semplificato utilizzabile in una fase di predimensionamento secondo il D.M. 14/01/2008 per l’impalcati a cassone monocellulare di sezione costante a una sola campata.

Non-contact lap splices placed within a single concrete placement are often used and have been studied in previous research projects. However, non-contact lap splices used with each bar in a different concrete placement such that there is a cold joint between the bars, have not been investigated. This situation is found in the repair of adjacent box beam bridges and in the construction of inverted T-beam systems, among others. It is vital to understand whether the same mechanisms are present across a cold joint with two different types of concrete as are present in traditional non-contact lap splices. In this research, eight T-beam specimens with non-contact lap splices were tested. The spacing between the bars, the splice bar blockout length, and presence of transverse bars were varied to study the effectiveness of the splices. The beams were tested in four point bending so that the splice region was under constant moment and the tension forces in the spliced bars were constant. End and midspan deflections were measured along with surface strain measurements at midspan and at the quarter span points, top and bottom. Gap openings were also measured at the ends of the blockouts. The main conclusions found from this research are that beams containing non-contact lap splices were able to develop nominal capacity with the bar spacing less than or equal to 4 in. and the blockout between 17 and 20 in. long. Extending the blockouts and adding transverse bars underneath the splices did not add to the capacity.
Master of Science