Relevant bibliographies by topics / Essai Double Cantilever Beam (DCB)

Contents

  1. Journal articles
  2. Dissertations / Theses
  3. Books
  4. Book chapters
  5. Conference papers

Academic literature on the topic 'Essai Double Cantilever Beam (DCB)'

Author: Grafiati
Published: 11 January 2025
Last updated: 31 July 2025

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles

Select a source type:

Consult the lists of relevant articles, books, theses, conference reports, and other scholarly sources on the topic 'Essai Double Cantilever Beam (DCB).'

Next to every source in the list of references, there is an 'Add to bibliography' button. Press on it, and we will generate automatically the bibliographic reference to the chosen work in the citation style you need: APA, MLA, Harvard, Chicago, Vancouver, etc.

You can also download the full text of the academic publication as pdf and read online its abstract whenever available in the metadata.

Journal articles on the topic "Essai Double Cantilever Beam (DCB)"

1

Alfred Franklin, V., T. Christopher, and B. Nageswara Rao. "Influence of Root Rotation on Delamination Fracture Toughness of Composites." International Journal of Aerospace Engineering 2014 (2014): 1–12. http://dx.doi.org/10.1155/2014/829698.

Full text
Abstract:
Large deviations have been observed while analysing composite double cantilever beam (DCB) specimens assuming each cracked half as a simple cantilever beam. This paper examines the effect of rotational spring stiffness(K)on the critical fracture energy(GIC)considering nonzero slope at the crack-tip of the DCB specimen by modelling each cracked half as the spring-hinged cantilever beam. The critical load estimates of DCB specimens fromGICare found to be in good agreement with in-house and existing test results of different composite material systems.
APA, Harvard, Vancouver, ISO, and other styles
2

Chen, T., C. M. Harvey, S. Wang, and V. V. Silberschmidt. "Analytical corrections for double-cantilever beam tests." International Journal of Fracture 229, no. 2 (2021): 269–76. http://dx.doi.org/10.1007/s10704-021-00556-5.

Full text
Abstract:
AbstractDouble-cantilever beams (DCBs) are widely used to study mode-I fracture behavior and to measure mode-I fracture toughness under quasi-static loads. Recently, the authors have developed analytical solutions for DCBs under dynamic loads with consideration of structural vibration and wave propagation. There are two methods of beam-theory-based data reduction to determine the energy release rate: (i) using an effective built-in boundary condition at the crack tip, and (ii) employing an elastic foundation to model the uncracked interface of the DCB. In this letter, analytical corrections fo
APA, Harvard, Vancouver, ISO, and other styles
3

Sponseller, David L., and Thomas E. Sponseller. "The Double Cantilever Beam (DCB) Test at Forty." BHM Berg- und Hüttenmännische Monatshefte 161, no. 1 (2016): 19–26. http://dx.doi.org/10.1007/s00501-016-0449-7.

Full text
APA, Harvard, Vancouver, ISO, and other styles
4

Colonel, L., A. Calvez, F. Fournel, et al. "Double cantilever beam bonding energy measurement using confocal IR microscopy." Journal of Applied Physics 132, no. 21 (2022): 215106. http://dx.doi.org/10.1063/5.0114668.

Full text
Abstract:
A new technique is assessed in order to measure, at the wafer scale, direct bonding energies. It is derived from the standard Double Cantilever Beam (DCB) method and uses interferometry in confocal IR laser source microscopy to measure crack openings. Such a bonding energy measurement protocol has better accuracy compared to other techniques. This is due to a better confocal microscopy resolution and the high intensity of the laser source. The elastic energy stored in bent wafers is obtained by measuring the beam curvature. DCB deformation models are discussed from the short-range crack openin
APA, Harvard, Vancouver, ISO, and other styles
5

Budzik, Michal K., and Henrik M. Jensen. "Evaluation of Defects in Adhesive Joint by Double Cantilever Beam Experiment." Key Engineering Materials 665 (September 2015): 101–4. http://dx.doi.org/10.4028/www.scientific.net/kem.665.101.

Full text
Abstract:
We analyzed effects of interface/adhesive defects during fracture mechanical Mode I Double Cantilever Beam (DCB) tests of an adhesive joint. Two aluminium slabs were bonded using structural epoxy adhesive. A DCB experiment under static loading was conducted to estimate the critical fracture energy. During the ‘steady-state’ fracture we noted oscillating, random fluctuation in the force vs. displacement curve, and thus in the fracture energy. This is associated to the local variation of properties within the bondline and the interfaces. A simple model is derived to quantify the probable density
APA, Harvard, Vancouver, ISO, and other styles
6

Wang, K. F., Y. Q. Wang, B. L. Wang, and L. Zheng. "A double cantilever beam incorporating cohesive crack modeling for superconductors." Modern Physics Letters B 34, no. 15 (2020): 2050166. http://dx.doi.org/10.1142/s0217984920501663.

Full text
Abstract:
In this paper, a double cantilever beam (DCB) specimen incorporating cohesive crack is developed for superconductors which have potential applications in high temperature superconducting cables in space solar power station. The cohesive interface is introduced along the crack front of the DCB model under electromagnetic force. The load-separation relation (i.e. the crack opening displacement) is used as the fracture mechanics parameter and the corresponding curves during fracture process are obtained and verified by the finite element numerical method. Results show that the presence of tensile
APA, Harvard, Vancouver, ISO, and other styles
7

Li, Rongzhi, Lin Ye, and Yiu-Wing Mai. "Interlaminar Fracture of Stitched GFRP Laminates." Advanced Composites Letters 5, no. 1 (1996): 096369359600500. http://dx.doi.org/10.1177/096369359600500101.

Full text
Abstract:
The mode I interlaminar fracture of Kevlar thread stitched GFRP laminates has been studied using double-cantilever-beam (DCB) tests. It was found that stitching density and patterns influence interlaminar fracture performance of composites mainly through the different failure mechanisms of stitch threads during crack propagation.
APA, Harvard, Vancouver, ISO, and other styles
8

Dahlan, Hendery, Meifal Rusli, Mulyadi Bur, and Rika Ampuh Hadiguna. "Kaji Teoritis Pengaruh Variasi Letak Retak Terhadap Perambatan Retak Dengan Pendekatan Double Cantilever Beam (DCB)." Jurnal Inovasi Rekayasa Mekanikal dan Termal 1, no. 2 (2023): 20–26. http://dx.doi.org/10.25077/inomet.1.2.20-26.2023.

Full text
Abstract:
One of the causes of structural failure is the presence of defects in the form of cracks that appear during the manufacturing or usage process of the structure. The propagation of cracks in the structure greatly depends on the value of the energy released rate possessed by the defective structure. Therefore, it is necessary to calculate the energy released rate of a structure that has a crack. One simple approach is the double cantilever beam (DCB) method. The DCB approach is derived from the change in strain energy with respect to the change in crack length. In this study, variations in crack
APA, Harvard, Vancouver, ISO, and other styles
9

Gourlie, A. D., G. N. Podolski, and J. R. Fleet. "A Detailed Statistical Examination of the Double Cantilever Beam (DCB) Test." CORROSION 47, no. 9 (1991): 728–35. http://dx.doi.org/10.5006/1.3585859.

Full text
APA, Harvard, Vancouver, ISO, and other styles
10

Christopoulos, G. C., and S. A. Paipetis. "Interlaminar Fatigue Crack Propagation in Mode I of Carbon Fiber/PEEK Composites." Advanced Composites Letters 2, no. 1 (1993): 096369359300200. http://dx.doi.org/10.1177/096369359300200101.

Full text
Abstract:
A study of the mode I interlaminar fracture toughness of a unidirectional carbon fibre reinforced thermoplastic matrix composite has been made using Double Cantilever Beam, DCB, specimens. Delamination growth per fatigue cycle, da/dN, was related with the maximum applied cyclic strain energy release rate, GIMAX, using a power law.
APA, Harvard, Vancouver, ISO, and other styles
More sources

Dissertations / Theses on the topic "Essai Double Cantilever Beam (DCB)"

1

Peignon, Axel. "Contribution au développement de méthodes de caractérisation et de modélisation de LVL de peuplier en vue de leur usage dans la mobilité." Electronic Thesis or Diss., Université de Toulouse (2023-....), 2024. http://www.theses.fr/2024TLSEI017.

Full text
Abstract:
Cette thèse s’inscrit dans le projet « BOOST » (acronyme de « le BOis pOur les STructures des véhicules ») financé par l’Agence Nationale de la Recherche (ANR). Il s’agit d’un Projet de Recherche Collaboratif entre l’ICA (Institut Clément Ader) à Toulouse et le LaBoMaP (LaBoratoire des Matériaux et Procédés) à Cluny.Le bois est une ressource locale, à très faible empreinte carbone et renouvelable. Largement utilisé dans l’aéronautique, mais aussi dans l’automobile en tant que structure travaillante dans le passé, son réemploi devient aujourd’hui un enjeu de la bioéconomie (Mair-Bauernfeind et
APA, Harvard, Vancouver, ISO, and other styles
2

Verdade, João Filipe Silva. "Comportamento à fadiga em modo I usando o ensaio Double Cantilever Beam modificado." Master's thesis, Universidade de Aveiro, 2016. http://hdl.handle.net/10773/17446.

Full text
Abstract:
Mestrado em Engenharia Mecânica<br>A delaminagem é um dos modos de rutura mais frequentes dos laminados compósitos, e que é geralmente tratado no âmbito da Mecânica da Fratura. Tem havido recentemente interesse crescente na caraterização do comportamento à delaminagem sob fadiga. O primeiro objetivo deste trabalho foi adaptar a máquina de baixo custo desenvolvida no Departamento de Engenharia Mecânica da Universidade de Aveiro à realização de ensaios de delaminagem sob fadiga em modo I. O segundo objetivo foi realizar alguns ensaios de laminado carbono/epóxido iniciando assim um estud
APA, Harvard, Vancouver, ISO, and other styles
3

Majeed, Moiz, and Teja Geesala Rahitya Venkata. "Characterization of thin laminate interface by using Double Cantilever Beam and End Notched Flexure tests." Thesis, Blekinge Tekniska Högskola, Institutionen för maskinteknik, 2020. http://urn.kb.se/resolve?urn=urn:nbn:se:bth-20852.

Full text
Abstract:
This thesis is intended to identify the mode I and mode II fracture toughness to characterize the thin laminate interface by using the Double Cantilever Beam test (DCB) and End Notched Flexure test (ENF). This study’s thin laminate was Polyethylene Terephthalate and Low-Density Polyethylene (PET-LDPE), which is mostly used by packaging industries in the manufacturing of packages to store liquid food. As PET-LDPE film is very flexible and difficult to handle, DCB and ENF tests cannot be performed directly so, sheet metal (Aluminium) was used as carrier material. PET-LDPE film is placed between
APA, Harvard, Vancouver, ISO, and other styles
4

Liswell, Brian P. "Exploration of Wood DCB Specimens Using Southern Yellow Pine for Monotonic and Cyclic Loading." Thesis, Virginia Tech, 2004. http://hdl.handle.net/10919/9955.

Full text
Abstract:
The primary direction of this thesis was towards exploring qualitative and quantitative characteristics necessary for refining and understanding the flat wood double cantilever beam (DCB) as a valid means for testing Mode I fracture energy in wood adhesive bonds. Southern yellow pine (SYP) adherends were used with epoxy and phenol formaldehyde (PF) impregnated films, providing two systems with different characteristics for investigation. An adhesive penetration analysis was performed for both the epoxy and PF bonds. The PF penetration into the SYP was shown to be relatively shallow. The epoxy
APA, Harvard, Vancouver, ISO, and other styles
5

Guan, Youliang. "Crack path selection and shear toughening effects due to mixed mode loading and varied surface properties in beam-like adhesively bonded joints." Diss., Virginia Tech, 2014. http://hdl.handle.net/10919/24905.

Full text
Abstract:
Structural adhesives are widely used with great success, and yet occasional failures can occur, often resulting from improper bonding procedures or joint design, overload or other detrimental service situations, or in response to a variety of environmental challenges. In these situations, cracks can start within the adhesive layer or debonds can initiate near an interface. The paths taken by propagating cracks can affect the resistance to failure and the subsequent service lives of the bonded structures. The behavior of propagating cracks in adhesive joints remains of interest, including wh
APA, Harvard, Vancouver, ISO, and other styles
6

Fontes, Joel da Silva. "Aplicação da correlação digital de imagem ao estudo da fratura em modo I de ligações coladas." Master's thesis, Universidade de Aveiro, 2017. http://hdl.handle.net/10773/22495.

Full text
Abstract:
Mestrado em Engenharia Mecânica<br>As ligações coladas estão a ter utilização crescente em aplicações estruturais devido às vantagens que têm relativamente a formas tradicionais de ligação, como as ligações aparafusadas e rebitadas. Todavia, subsistem incertezas acerca do comportamento das ligações coladas, que por isso continuam a ser objeto de vários trabalhos de investigação. Esta dissertação incidiu sobre o comportamento à fratura em modo I de ligações de substratos de aço colados com adesivo epóxido. O objetivo principal foi desenvolver e avaliar uma nova forma de aplicação da correlação
APA, Harvard, Vancouver, ISO, and other styles
7

Budhe, Sandip Rudha. "Effect of pre-bond moisture on the static and fatigue behaviour of bonded joints between CFRP laminates for structural repairs." Doctoral thesis, Universitat de Girona, 2014. http://hdl.handle.net/10803/283567.

Full text
Abstract:
In recent years, the use of composite materials in the aeronautic, automotive, marine construction, etc. has increased significantly. Hence, there is an increasing need for repair technologies on primary structural components, as replacing a damaged component by a new one is not cost effective in many cases. The composite structures experience damage in service that comes from accidental impacts, mechanical stresses, environmental factors (moisture and temperature), etc. Thus, maintenance and repair is the concern of the end users as well as of the manufacturers. Suitable material systems and
APA, Harvard, Vancouver, ISO, and other styles

Books on the topic "Essai Double Cantilever Beam (DCB)"

1

Pavlovskis, Pēteris. Analysis of Two Actual Problems of Interlaminar Fracture Assessment of Layered Composite. RTU Press, 2022. http://dx.doi.org/10.7250/9789934228148.

Full text
Abstract:
Two types of specimens were studied based on applying the nonlinear theory of flexible plates to obtain the interlaminar fracture toughness of layered composites. For a specimen of the thin sub-layer type, a theoretical solution was obtained in relation to the determination of the interlaminar fracture toughness for a mixed II/I mode. The fundamental possibility of using this solution in test practice was confirmed. The application of the nonlinear theory of flexible plates to the well-known standard specimen of the double-cantilever beam (DCB) was studied in more detail. A theoretical solutio
APA, Harvard, Vancouver, ISO, and other styles

Book chapters on the topic "Essai Double Cantilever Beam (DCB)"

1

Sun, Chen, Minghua Dai, Liang Ying, Kai Du, Zhigang Chen, and Ping Hu. "Experimental and Numerical Simulation on Formability and Failure Behavior of Thermoplastic Carbon Fiber/AL Composite Laminates." In Lecture Notes in Mechanical Engineering. Springer International Publishing, 2024. http://dx.doi.org/10.1007/978-3-031-58006-2_30.

Full text
Abstract:
AbstractCarbon fiber reinforced thermoplastic/aluminum alloy (CFRTP/AL) composite laminates have the advantages of low density, high specific strength, and good fatigue resistance, which is a new type of engineering composite material to realize lightweight vehicle body. Heterogeneous interface delamination failure occurs in the forming process of the fiber metal laminates (FMLs). It is necessary to establish an effective finite element simulation strategy to accurately predict the delamination failure behavior of FMLs. In this work, thermoplastic PA6 continuous carbon fiber/AL FMLs were taken
APA, Harvard, Vancouver, ISO, and other styles
2

Meltem Toygar, Evren, and Ahmet Gulakman. "Failure Modes in Fiber Reinforced Composites and Fracture Toughness Testing of FRP." In Advances in Fatigue and Fracture Testing and Modelling. IntechOpen, 2022. http://dx.doi.org/10.5772/intechopen.99268.

Full text
Abstract:
In this paper, interlaminar fracture behavior of woven-fabric-reinforced glass/epoxy composites has been investigated experimentally and numerically. The mechanical properties of this composite were studied and Mode I (Tensile Opening) DCB (Double Cantilever Beam) tests were performed on Fiber Reinforced Composite (FRP) specimens to determine the delaminating resistance of composite laminates used for structural applications. Techniques for measuring the interlaminar fracture toughness, KIC data of woven-fabric-reinforced glass/epoxy composite materials, are highlighted under the consideration
APA, Harvard, Vancouver, ISO, and other styles
3

Gaona-Tiburcio, Citlalli, Alejandro Lira-Martínez, Marianggy Gomez-Avila, et al. "Delamination and Tensile Effect of Fine z-Binder Reinforced on Fiberglass/Polyester Composite for Aerospace Applications." In Next Generation Fiber-Reinforced Composites - New Insights [Working Title]. IntechOpen, 2022. http://dx.doi.org/10.5772/intechopen.106927.

Full text
Abstract:
Delamination propagation in laminated composite materials is a common issue that always concerns us when we consider composites for structural purpose. Many possible solutions have been studied; the most famous is the three-dimensional (3D) woven composites materials, which have promising interlaminar fracture resistance but at the cost of increasing density, which for aerospace industry is very important. In this chapter, mode 1 double cantilever beam (DCB) interlaminar fracture toughness tests according to the American Society for Testing and Materials (ASTM) D5528 standard were performed on
APA, Harvard, Vancouver, ISO, and other styles

Conference papers on the topic "Essai Double Cantilever Beam (DCB)"

1

Szklarz, K. E. "Interpreting and Using the NACE Double Cantilever Beam (DCB) Test." In CORROSION 2008. NACE International, 2008. https://doi.org/10.5006/c2008-08108.

Full text
Abstract:
Abstract The NACE TM0177 Method D (DCB) test is a blend of interactive physical and chemical conditions. It is becoming a common test used successfully throughout the world. After more than 25 years of DCB testing, this paper considers some of the following issues. What KISSC are we calculating and using, especially when changing the environment of exposure? How can we verify the mechanical aspects of the test? What are the obvious and not so obvious variations in the test? If the test is not done perfectly can you still use the data? How should we improve the test method?
APA, Harvard, Vancouver, ISO, and other styles
2

Pérez, T. E., R. Herrera, P. R. Hatcher, and K. E. Szklarz. "A Modified KISSC Calculation for Double Cantilever Beam Specimens." In CORROSION 1993. NACE International, 1993. https://doi.org/10.5006/c1993-93142.

Full text
Abstract:
Abstract Elastic compliance and stress intensity factor, K, expressions for standard NACE TM0177-90 DCB and other geometries were determined for a wide range of crack length to arm height ratios (2.75 &amp;lt; a/h &amp;lt; 5.35). These expressions were obtained from experimental measurements on various specimen geometries, including two different specimen thicknesses, 4.77 mm (3/16") and 9.53 mm (3/8") and four side groove depth to thickness ratios (B/Bn= 1.0, 1.25, 1.66, 2.0). An effective thickness that makes the compliance expression side groove depth independent is proposed. Based on compl
APA, Harvard, Vancouver, ISO, and other styles
3

Roy, Ajit K., Dennis C. Freeman, and Maura K. Spragge. "Stress Corrosion Cracking Evaluation of Candidate Container Alloys by Double Cantilever Beam Method." In CORROSION 2000. NACE International, 2000. https://doi.org/10.5006/c2000-00189.

Full text
Abstract:
Abstract The susceptibility to stress corrosion cracking (SCC) of two candidate container materials for the multi-barrier nuclear waste package was evaluated by using wedge-loaded and precracked double-cantilever-beam (DCB) specimens in a deaerated 90°C acidic brine (pH ≈ 2.7). Materials tested include Alloy 22 (UNS N06022) and Ti Grade-12 (UNS R53400). Duplicate samples of each material were loaded at different initial stress-intensity factor (KI) values that ranged from 18 to 47 MPa√m. The DCB specimens were exposed to the test solution for one year. Both compliance and metallographic method
APA, Harvard, Vancouver, ISO, and other styles
4

Szklarz, K. E., and T. E. Pérez. "Observations on the Use of the Double Cantilever Beam Specimen for Sulfide Stress Corrosion Tests." In CORROSION 1995. NACE International, 1995. https://doi.org/10.5006/c1995-95048.

Full text
Abstract:
Abstract This paper summarizes observations made by the authors over the last few years on the double-cantilever-beam (DCB) coupon and associated testing methodology. The NACE coupon compliance was experimentally determined and the accuracy of calculated stress intensity factors discussed. The difference between 7 and 14 day exposures are shown and a suggestion made for a reduced exposure. The importance of proper fatigue precracking is highlighted and the effect of DCB geometry with respect to out-of-plane cracking discussed.
APA, Harvard, Vancouver, ISO, and other styles
5

Sponseller, D. L. "Interlaboratory Testing of Seven Alloys for SSC Resistance by the Double-Cantilever-Beam (TM0177-90D) Method." In CORROSION 1991. NACE International, 1991. https://doi.org/10.5006/c1991-91003.

Full text
Abstract:
Abstract Seven alloys of interest for deep sour-gas wells were evaluated for sulfide-stress-cracking resistance by the double-cantilever-beam (DCB) method. Representatives of 20 laboratories participated in one or both of two round-robin testing programs. These were conducted in support of the successful effort to include the DCB test in an expanded NACE test method, TM0177-90. Test materials included cast and wrought products, low-alloy and stainless steels, and nonferrous alloys. The test results reveal generally minor variation of KISSC within data-sets from individual laboratories, but rat
APA, Harvard, Vancouver, ISO, and other styles
6

Gourlie, A. D., G. N. Podolski, and J. R. Fleet. "A Measurement System Evaluation of the DCB Test and a Comparative Analysis of the Effect of Different Coupons on DCB Performance." In CORROSION 1989. NACE International, 1989. https://doi.org/10.5006/c1989-89010.

Full text
Abstract:
Abstract This paper examines the accuracy and precision of the Double Cantilever Beam (DCB) test using sources of variation analysis and multilinear regression. It is estimated that greater than 90% of the total variation in test results is explainable. It is also concluded that the least significant source of test result variation is the standard deviation identified as test variation. Geometric and machining effects are also examined in detail. It is shown that a difference on average of approximately 3.5 ksi√in. can exist for the two test methods and coupon geometries studied. However the s
APA, Harvard, Vancouver, ISO, and other styles
7

Turkalj, Tomás, Ricardo Schifini, Sebastian Cravero, Gustavo Kissner, and Hugo Ernst. "Uncertainty Assessment in DCB Testing." In CORROSION 2015. NACE International, 2015. https://doi.org/10.5006/c2015-05858.

Full text
Abstract:
Abstract Method D, Double cantilever beam (DCB) test is used for design/fitness-for-service, material qualification and specification purposes. Material resistance to propagation of environmental cracks is expressed in terms of a critical stress intensity factor KISSC or Klimit values. Usually, these values are determined without considering the experimental uncertainties and material variability. However, when comparing the sulfide stress corrosion cracking (SSC) performance of different materials, the quantification of experimental uncertainties becomes of fundamental importance. If the frac
APA, Harvard, Vancouver, ISO, and other styles
8

Guntz, G. C., C. P. Linne, F. Puissochet, B. J. Orlans-Joliet, R. K. Poepperling, and J. M. Fliethmann. "DCB Test: a Review of Critical Parameters." In CORROSION 1999. NACE International, 1999. https://doi.org/10.5006/c1999-99606.

Full text
Abstract:
Abstract The presence of H2S in well fluids imposes severe restrictions on the use of tubular goods because of sulfide stress cracking (SSC). Increasing developments of deep sour wells require high strength OCTG with improved SSC resistance. The appropriate selection of materials for well completion is an important factor in economic success of oil and gas production. Corrosion cracking behaviour of metals for the range of environments expected in service is the main criterion. Such knowledge is gained partly from service experience, but mainly from appropriate laboratory testing at the design
APA, Harvard, Vancouver, ISO, and other styles
9

Turkalj, Tomás, Sebastián Cravero, Hugo Ernst, and Gustavo Kissner. "Effect of High Arm Displacement on DCB Specimen Testing." In CORROSION 2015. NACE International, 2015. https://doi.org/10.5006/c2015-05856.

Full text
Abstract:
Abstract Usually Double Cantilever Beam (DCB) samples are tested following NACE Standard TM0177-2005 procedure. The standard establish arm displacement limits as function of steel grade. However, the increasing interest on material characterization in mild sour media imposes testing at higher arm displacements that can produce larger plasticization zones at the crack-tip of DCB specimens. It is widely recognized that the level of plasticity can significantly affect the material fracture behavior. Therefore, It is important to study the loading conditions that cause the loss of linear elastic r
APA, Harvard, Vancouver, ISO, and other styles
10

Nakamura, Jun, Keiichi Kondo, Hiroki Kamitani, Hisashi Amaya, and Mutsumi Tanida. "The Effect of Crack Start Positions for Chevron Notch Type on NACE TM0177 DCB Elastic Compliance." In CORROSION 2019. NACE International, 2019. https://doi.org/10.5006/c2019-12842.

Full text
Abstract:
Abstract The Double Cantilever Beam (DCB) test method standardized in NACE TM0177 is increasingly applied as a quality assurance test to specify the performance of carbon and low alloy steels for sour service. The DCB test method has been modified and specified tightly from the view point of specimen geometry, test environment, and initial stress intensity factor controlled by arm displacement to obtain highly repeatable test results. NACE TM0177 2016 method D has various types of starter notch configurations on DCB specimens. Crack start position shifted change specimen of EDM notch has been
APA, Harvard, Vancouver, ISO, and other styles
You might also be interested in the extended bibliographies on the topic 'Essai Double Cantilever Beam (DCB)' for particular source types:
Journal articles
We offer discounts on all premium plans for authors whose works are included in thematic literature selections. Contact us to get a unique promo code!

To the bibliography