Dissertations / Theses on the topic 'Grid-connected Applications'

The emergence of silicon-carbide (SiC) devices has been a 'game changer' in the field of power electronics. With desirable material properties such as low-loss characteristics, high blocking voltage, and high junction temperature operation, they are expected to drastically increase the power density of power electronics systems. Recent state-of-the-art designs show the power density over 17 ; however, certain factors limit the power density to increase beyond this limit. In this dissertation, three key factors are selected to increase the power density of SiC-based grid-connected three-phase converters. Throughout this dissertation, the techniques and strategies to increase the power density of SiC three-phase converters were investigated. Firstly, a magnetic integration method was introduced for the coupled inductors in the interleaved three-phase converters. Due to limited current-capacity compared to the silicon insulated-gate bipolar transistors (Si-IGBTs), discrete SiC devices or SiC modules, operate in parallel to handle a large current. When three-phase inverters are paralleled, interleaving can be used, and coupled inductors are employed to limit the circulating current. In Chapter 2, the conventional integration method was extended to integrate three coupled inductors into two; one for differential-mode circulating current and the other for common-mode circulating current. By comparing with prior research work, a 20% reduction in size and weight is demonstrated. From Chapter 3 to Chapter 5, a full-SiC uninterruptible power supply (UPS) was investigated. With the high switching frequency and fast switching dynamics of SiC devices, strategies on electromagnetic inference become more important, compared to Si-IGBT based inverters. Chapter 3 focuses on a common-mode equivalent circuit model for a topology and pulse width modulation (PWM) scheme selection, to set a noise mitigation strategy in the design phase. A three terminal common-mode electromagnetic interference (EMI) model is proposed, which predicts the impact of the dc-dc stage and a large battery-rack on the output CM noise. Based on the model, severe deterioration of noise by the dc-dc stage and battery-rack can be predicted. Special attention was paid on the selection of the dc-dc stage's topology and the PWM scheme to minimize the impact. With the mitigation strategy, a maximum 16 dB reduction on CM EMI can be achieved for a wide frequency range. In Chapter 4, an active PWM scheme for a full-SiC three-level back-to-back converter was proposed. The PWM scheme targets the size reduction of two key components: dc-link capacitors and a common-mode EMI filter. The increase in switching frequency calls for a large common-mode EMI filter, and dc-link capacitors in the three-level topology may take a considerable portion in the total volume. To reduce the common-mode noise emission, different combinations of the voltage vectors are investigated to generate center-aligned single pulse common-mode voltage. By such an alignment of common-mode voltage with different vector combinations, noise cancellation between the rectifier and the inverter can be maximally utilized, while the balancing of neutral point voltage can be achieved by the transition between the combinations. Also, to reduce the size of the dc-link capacitor for the three-level back-to-back converter, a compensation algorithm for neutral point voltage unbalance was developed for both differential-mode voltage and the common-mode voltage of the ac-ac stage. The experimental results show a 4 dB reduction on CM EMI, which leads to a 30% reduction on the required CM inductance value. When a 10% variation of neutral point voltage can be handled, the dc-link capacitance can be reduced by 56%. In Chapter 5, a 20 kW full-SiC UPS prototype was built to demonstrate a possible size-reduction with the proposed PWM scheme, as well as a selection of topologies and PWM schemes based on the model. The power density and efficiency are compared with the state-of-the-art Si-IGBT based UPSs. Chapter 6 seeks to improve power density by a change in a modulation method. Triangular conduction mode (TCM) operation of the three-level full-SiC inverter was investigated. The switching loss of SiC devices is reported to be concentrated on the turn-on instant. With zero-voltage turn-on of all switches, the switching frequency of a three-level three-phase SiC inverter can be drastically increased, compared to the hard-switching operation. This contributes to the size-reduction of the filter inductors and EMI filters. Based on the design to achieve a 99% peak efficiency, a comparison was made with a full-SiC three-level inverter, operating in continuous conduction mode (CCM), to verify the benefit of the soft switching scheme on the power density. A design procedure for an LCL filter of paralleled TCM inverters was developed. With 3.5 times high switching frequency, the total weight of the filter stage of the TCM inverter can be reduced by 15%, compared to that of the CCM inverter. Throughout this dissertation, techniques for size reduction of key components are introduced, including coupled inductors in parallel inverters, an EMI filter, dc-link capacitors, and the main boost inductor. From Chapter 2 to 5, the physical size or required value of these key components could be reduced by 20% to 56% by different schemes such as magnetic integration, EMI mitigation strategy through modeling, and an active PWM scheme. An optimization result for a full-SiC UPS showed a 40% decrease in the total volume, compared to the state-of-the-art Si-IGBT solution. Soft-switching modulation for SiC-based three-phase inverters can bring a significant increase in the switching frequency and has the potential to enhance power-density notably. A three-level three-phase full-SiC 40 kW PV inverter with TCM operation contributed to a 15% reduction on the filter weight.<br>Doctor of Philosophy<br>The power density of a power electronics system is regarded as an indicator of technological advances. The higher the power density of the power supply, the more power it can generate with the given volume and weight. The size requirement on power electronics has been driven towards tighter limits, as the dependency on electric energy increases with the electrification of transportation and the emergence of grid-connected renewable energy sources. However, the efficiency of a power electronics system is an essential factor and is regarded as a trade-off with the power density. The size of power electronics systems is largely impacted by its magnetic components for filtering, as well as its cooling system, such as a heatsink. Once the switching frequency of power semiconductors is increased to lower the burden on filtering, more loss is generated from filters and semiconductors, thus enlarging the size of the cooling system. Therefore, considering the efficiency has to be maintained at a reasonable value, the power density of Si-based converters appears to be saturated. With the emergence of wide-bandgap devices such as silicon carbide (SiC) or gallium nitride (GaN), the switching frequency of power devices can be significantly increased. This is a result of superior material properties, compared to Si-based power semiconductors. For grid-connected applications, SiC devices are adopted, due to the limitations of voltage ratings in GaN devices. Before commercial SiC devices were available, the power density of SiC- based three-phase inverters was expected to go over 20 𝑘𝑊 𝑑𝑚3 ⁄ . However, the state-of-the art designs shows the power density around 3 ~ 4 𝑘𝑊 𝑑𝑚3 ⁄ , and at most 17 𝑘𝑊 𝑑𝑚3 ⁄ . The SiC devices could increase the power density, but they have not reached the level expected. The adoption of SiC devices with faster switching was not a panacea for power density improvement. This dissertation starts with an analysis of the factors that prevent power density improvement of SiC-based, grid-connected, three-phase inverters. Three factors were identified: a limited increase in the switching frequency, large high-frequency noise generation to be filtered, and smaller but still significant magnetic components. Using a generic design procedure for three-phase inverters, each chapter seeks to frame a strategy and develop techniques to enhance the power density. For smaller magnetic components, a magnetic integration scheme is proposed for paralleled ac-dc converters. To reduce the size of the noise filter, an accurate modeling approach was taken to predict the noise phenomena during the design phase. Also, a modulation scheme to minimize the noise generation of the ac-ac stage is proposed. The validity of the proposed technique was verified by a full-SiC three-phase uninterruptible power supply with optimized hardware design. Lastly, the benefit of soft-switching modulation, which leads to a significant increase in switching frequency, was analyzed. The hardware optimization procedure was developed and compared to hard-switched three-phase inverters.

Renewable or sustainable energy (SE) sources have attracted the attention of many countries because the power generated is environmentally friendly, and the sources are not subject to the instability of price and availability. This dissertation presents new trends in the DC-AC converters (inverters) used in renewable energy sources, particularly for photovoltaic (PV) energy systems. A review of the existing technologies is performed for both single-phase and three-phase systems, and the pros and cons of the best candidates are investigated. In many modern energy conversion systems, a DC voltage, which is provided from a SE source or energy storage device, must be boosted and converted to an AC voltage with a fixed amplitude and frequency. A novel switching pattern based on the concept of the conventional space-vector pulse-width-modulated (SVPWM) technique is developed for single-stage, boost-inverters using the topology of current source inverters (CSI). The six main switching states, and two zeros, with three switches conducting at any given instant in conventional SVPWM techniques are modified herein into three charging states and six discharging states with only two switches conducting at any given instant. The charging states are necessary in order to boost the DC input voltage. It is demonstrated that the CSI topology in conjunction with the developed switching pattern is capable of providing the required residential AC voltage from a low DC voltage of one PV panel at its rated power for both linear and nonlinear loads. In a micro-grid, the active and reactive power control and consequently voltage regulation is one of the main requirements. Therefore, the capability of the single-stage boost-inverter in controlling the active power and providing the reactive power is investigated. It is demonstrated that the injected active and reactive power can be independently controlled through two modulation indices introduced in the proposed switching algorithm. The system is capable of injecting a desirable level of reactive power, while the maximum power point tracking (MPPT) dictates the desirable active power. The developed switching pattern is experimentally verified through a laboratory scaled three-phase 200W boost-inverter for both grid-connected and stand-alone cases and the results are presented.