Academic literature on the topic 'Industrial microbiology - Equipment and supplies'

Defence industry may be defined as a system of factories and organisations developing, manufacturing and selling military equipment, weapons and ammunition. In the case of the Russian Federation the terminology of “defence industry” and “military industry” is often used as an equivalent to the Military-Industrial Complex (MIC). The Military-Industrial Complex is a segment of the state industry involved in manufacture of the military equipment and performance of research-development projects in the defence sector. Typical feature of the Military-Industrial Complex is that the state is always its customer. Level of development for the Russian MIC plays a crucial role for maintaining the safety of the state and beside the supplies for the army it is responsible in a great degree for technical equipment of main segments of economy (medicine, transport, education, fuelenergetic complex, etc.). The governing board of the MIC in-cludes 18 persons led by the President of Russian Federation - Vladimir Putin.

Sugarcane industry in Brazil is highly competitive in the production of ethanol, sugar and energy. This industrial competitiveness was also achieved through the development of the equipment involved in the production processes. The industry that supplies the equipment plays an important role in the competitiveness of sugarcane sector. This study seeks to analyze the organization and configuration of the equipment supply industries for sugar, ethanol and energy mills in Brazil. The study seeks to evaluate how innovation occurs in this sector, contributing to an important discussion about maintaining competitiveness and proposing a typology for this industry. The study is based on an analysis of information obtained through a set of interviews with leaders and entrepreneurs in the industry. The results allow us to conclude that the growing modernization of the sector will require greater efforts from the equipment industry to provide plants with necessary technological innovations and possible efficiency gains

This article investigates the impact of “learning-by-producing” on inventive activity. From 1870 to 1910, in both emerging (electrical equipment and supplies) and maturing (shoes and textiles) industries, the geographic association between invention and production was rather weak. Regional shifts in production did not lead to corresponding increases in invention. The location of inventive activity tended to mirror that of individuals with advanced technical skills appropriate to each industry. Consequently, scholars may have overemphasized the importance of learning-by-producing in accounting for geographic differences in inventive activity, and underestimated the significance of technical skills amongst the population.

Objective. This study is aimed at describing a score to assess infection control structures in Oral Health Teams (OHT) in Primary Health Care (PHC) in Brazil. Methods. Secondary data from a national external evaluation of PHC conducted in 2017 and 2018 were analyzed. The construction of the score used 14 variables, divided into the following: structural characteristics of the PHC, infection control equipment under conditions of use, and biosafety supplies in sufficient quantity. The questions were mostly dichotomous (yes/no). Descriptive analyses were carried out to characterize the OHT and factor analyses to reduce the number of observed variables to a specific number of factors. Results. Among 20,301 health units with OHT, 4,510 (22.2%) units did not have washable floors, ceilings, and walls; 8,406 (41.4%) did not have a sealer; 16,780 (82.7%) did not have taps with noncontact activation, and 4,663 (23.0%) units did not have rubber gloves. Regarding personal protective equipment (PPE), 1,618 (8.0%) units did not have a sufficient quantity of basic PPE. Three factors were defined to explain the 14 evaluated variables. The South region had the best score of infection control, while the North had the worst. Conclusions. Regional inequalities in the failures in infection control structures identified in PHC with OHT were related to the physical structure, equipment, and supplies used for infection control and the absence of PPE for OHT.

Bundling materials for calculated intentions are intended to ensure electrical and electronic items and other delicate purchaser products from harms because of stun and over the top vibrations during dealing with and transportation. There is as of late an expanded worry for the improvement of very much planned as well as practical materials. Material maintainability is frequently connected with the extraction of sustainable assets and removal techniques that would not harm our biological system. In this regard, home-grown agro-squander assets would be a savvy choice to create unimportant and expendable green equipment effortlessly. This article features a portion of the answer utilities or elements of bundling supplies and the financially accessible bundling. The possibility of biodegradable materials including indigenous common strands and a case of totally compostable business bundling substance are illustrated. Fundamental aftereffects of stun padding test on surface-adjusted polypropylene arranged in this investigation demonstrated 20% ideal substance padding are introduced.

During the spring of 1983, fluid milk samples were collected from 359 bulk transporters representing 16 counties, municipalities and districts of Ontario, and were analyzed for organochlorine and organophosphorus insecticides plus selected halogenated industrial pollutants. Dieldrin, p,p′-DDE, heptachlor epoxide, and α-BHC were found in over 90% of samples, but none exceeded the accepted maximum residue limits. Polychlorinated biphenyls (PCB), lindane and pentachlorophenol (PCP) were found in 83, 68 and 57% of samples, respectively, with four samples exceeding the permissable PCB limit and one sample exceeding the permissable PCP limit. Residues of chlordane, endosulfan, p,p′-TDE, and p,p′-DDT were identified in only 1.9 to 4.7% of samples, and were present at levels only slightly above the detection limits. Hexachlorobenzene (HCB) was found at low levels in 40% of samples. Mean residues of organochlorines found were as follows (μg/kg butterfat): ∑DDT - 12; α-BHC - 5.3; lindane - 4.0; heptachlor epoxide - 3.9; dieldrin - 6.2; HCB - 0.67; PCB - 24; and PCP - 29. No residues of six organophosphorus insecticides, endrin, methoxychlor or mirex were detected in any samples. This survey was the sixth in a series beginning in 1967. Half-residue disappearance rates were calculated at 3.5, 5.4, 5.6 and 3.0 years for ∑DDT, dieldrin, PCB and HCB, respectively. A case history is included involving the misapplication of fenthion to a dairy herd which revealed a half-residue elimination from milk in approximately 3 d.

Psychrotrophic bacteria have been recognized as a recurring problem in the refrigerated storage and distribution of fluid milk and cream and other perishable dairy products for several decades. Much emphasis has been focused on postpasteurization contaminants that are psychrotrophic, (e.g., Pseudomonas, Flavobacterium, and Alcaligenes spp.). Common sources of these gram-negative, non-sporeforming organisms are equipment surfaces and water supplies. Although these organisms are generally heat sensitive, many of their associated proteinases and lipases can withstand moderate to severe heat treatments and cause product deterioration. With the advance of improved control of postpasteurization contamination by nonheat-resistant psychrotrophs, more recent attention has been directed at psychrotrophic sporeformers and their potential impact on milk quality and shelf life properties. Heat-resistant psychrotrophs include members from the genera Clostridium, Arthrobacter, Microbacterium, Streptococcus, Corynebacterium, and Bacillus. However, the predominant microorganisms which comprise this category are Bacillus species. These bacteria can be introduced into milk supplies from water, udder and teat surfaces, or from soil and milkstone deposits on farm bulk tanks, pumps, pipelines, gaskets, and processing equipment. There is speculation that they can also be postpasteurization contaminants. When in the spore state, these microorganisms easily survive the typical range of pasteurization conditions with subsequent germination and outgrowth of vegetative cells. These organisms produce degradative enzymes (e.g., proteinases, lipases, and phospholipases) similar to those of non-sporeforming psychrotrophs. Enzymatic activity results in the development of objectionable flavor and quality defects in dairy products. The unique combination of both heat-resistant and psychrotrophic properties with the same microorganism represents substantial potential for causing spoilage of perishable milk products. Recent trends of higher pasteurization temperatures and extended refrigerated storage time of both raw and pasteurized milk and cream products exacerbates the significance of this group of microorganisms for the dairy foods industry.

Corrosion, aging, wear of the basic production assets of the of the Kuznetsk Basin coal industry enterprises lead to huge losses of natural resources and material supplies; labor costs being increased. Most failures, breakdowns, malfunctions at industrial facilities, except for cases of misuse, are caused by the above mentioned factors. Therefore, the primary task is to develop methods for protecting equipment from corrosion. In this paper, the measures to increase the longevity of polymer-silicate mastic protective coatings by studying and optimizing the group of internal properties of polymer-silicates that determine the properties of the coating as a whole are proposed.

Abstract Background Hospitals use standard and transmission-based precautions, including personal protective equipment (PPE), to prevent the spread of infectious organisms. However, little attention has been paid to the potentially unique challenges of various healthcare personnel (HCP) in following precaution practices. Methods From September through December 2016, 5 physicians, 5 nurses, and 4 physical therapists were shadowed for 1 hour 30 minutes to 3 hours 15 minutes at an academic medical center. Observers documented activities using unstructured field notes. Focus groups were conducted to better understand HCP perspectives about precautions and PPE-related challenges. Data were analyzed by comparing workflow and challenges (observed and stated) in precaution practices across HCP roles. Results Precaution patients were interspersed throughout physician rounds, which covered a broad geographic range throughout the hospital. Patient encounters were generally brief, and appropriate use of gowns and cleaning of personal stethoscopes varied among observed physicians. Nurses were unit based and frequently entered/exited rooms. Frustration with donning/doffing was especially apparent when needing supplies while in a precaution room, which nurses acknowledged was a time when practice lapses could occur. The observed physical therapists worked in one geographic location, spent extended periods of time with patients, and noted that given their close physical contact with patients, gowns do not fully protect them. Conclusions Movement patterns, time with patients, care activities, and equipment use varied across HCP, leading to a diverse set of challenges in following precaution practices and PPE use. Attention to these differences among HCP is important for understanding and developing effective strategies to prevent the potential spread of infectious organisms.

Neste trabalho, são descritos os detalhes da montagem de um sistema de cultivo microbiano em estado sólido, cujo elemento principal é um biorreator de tambor rotativo em escala de bancada, com casco em vidro refratário com aproximadamente 6,2 litros de volume. A montagem do equipamento exigiu estudos para a definição dos seguintes aspectos: geometria do reator; controle de frequência e período de agitação; umidificação, aquecimento e controle do fluxo do ar injetado no sistema; mistura do meio de cultivo; medição e controle da temperatura do meio; retirada de amostras. O sistema desenvolvido foi avaliado, tendo como processo fermentativo modelo o cultivo de Aspergillus niger T0005/007-2, microrganismo produtor de enzimas pectinolíticas. Os testes foram feitos em um meio contendo farelo de trigo como suporte sólido, avaliando-se a influência de três parâmetros principais agitação, massa de meio de cultivo e temperatura do meio sobre o crescimento celular e a produção de endo-poligalacturonase (PG) por A. niger. Três formas de agitação do meio sólido foram comparadas: sem agitação; agitação a 1 rpm por 5 minutos a cada duas horas; agitação a 1 rpm por 1 hora e 55 minutos a cada duas horas. A segunda forma de agitação levou ao melhor crescimento celular, 81 mg.g-1, e a atividade de endo-PG da ordem de 80 U.g-1, semelhante ao estimado com o sistema estático. Com a terceira forma de agitação, aparentemente houve dano ao micélio fúngico e, com isso, resultados inferiores foram alcançados. A avaliação do efeito da massa de meio de cultivo sobre o processo foi feita com cargas crescentes de meio que resultaram na ocupação de 30, 45 e 60 % do volume útil do reator. Quanto ao crescimento celular, o melhor resultado foi alcançado com a menor carga de meio, enquanto que a carga intermediária resultou no mais alto título enzimático final, 107,2 U.g-1. Nos experimentos sobre a influência da temperatura sobre o cultivo de A. niger, a maior atividade enzimática (80,6 U.g-1) foi obtida numa condição de trabalho que permitiu que a temperatura do meio atingisse valores da ordem de 45ºC. Com o meio mantido a 30ºC, a atividade enzimática máxima foi substancialmente mais baixa, 46,4 U.g-1. Nos testes realizados com o processo modelo, não se verificou uma clara influência positiva da agitação sobre a produção de endo-PG. Entretanto, a partir dos experimentos com temperatura controlada, é possível sugerir que a formação de endo-PG é favorecida por uma condição de estresse para o microrganismo, no caso representado por temperaturas do meio acima de 40ºC, visto que a temperatura ideal de crescimento de A. niger encontra-se na faixa de 28 a 34ºC. Este resultado, que discorda do que é genericamente descrito na literatura especializada sobre cultivos em estado sólido, é um exemplo da importância de dispor-se de um biorreator de tambor rotativo de pequena escala como equipamento básico para a realização de estudos fundamentais a respeito deste tipo de processo. Adicionalmente, o fato de o corpo do reator ser construído em vidro permite a visualização do espaço interno do tambor rotativo e observar o efeito da agitação sobre o meio de cultivo.
Submitted by Marcelo Teixeira (mvteixeira@ucs.br) on 2014-06-02T17:41:21Z No. of bitstreams: 1 Dissertacao Tomas Augusto Polidoro.pdf: 1493269 bytes, checksum: 0ed8a1384e54fe0a00f47be237707cbf (MD5)
Made available in DSpace on 2014-06-02T17:41:21Z (GMT). No. of bitstreams: 1 Dissertacao Tomas Augusto Polidoro.pdf: 1493269 bytes, checksum: 0ed8a1384e54fe0a00f47be237707cbf (MD5)
In this work, details on the assembling of a solid state cultivation system, whose main component is a bench scale rotating-drum bioreactor, are described. The bioreactor was built in refractory glass and has an approximate volume of 6.2 liters. To assemble the equipment, the following aspects have been studied: geometry of the bioreactor; control of frequency and period of agitation; moistening, warming and controlling of the inlet air flux; mixing of cultivation medium; determination and control of medium temperature; sample withdrawn. The developed system was evaluated, being the cultivation of the pectinolytic enzymeproducing microorganism Aspergillus niger T0005/007-2 used as the model process. The fermentative tests were carried out in a medium containing wheat-straw as solid support and were used to evaluate the effects of three main parameters agitation, mass of cultivation medium and medium temperature on the cell growth and the production of endopolygalacturonase (endo-PG) by A. niger. For agitation of the solid medium, three modes were compared: no agitation; agitation of 1 rpm for 5 minutes each 2 hours; agitation for 1 hour and 55 minutes, each 2 hours. The second mode of agitation led to the best cell growth, 81 mg.g-1, and to endo-PG activity of approximately 80 U.g-1, similar to that obtained with the static system. With the third mode of agitation occurred, apparently, some damage to fungus mycelium and inferior results were achieved. The evaluation of the mass of cultivation medium on the process was done by loading the reactor with masses that result in the occupation of 30, 45 and 60% of the working volume of the bioreactor. With respect to the cell growth, the best result was attained with the smallest load of medium, whereas the intermediate load resulted in the highest endo-PG activity, 107.2 U.g-1. In the experiments on the influence of the temperature on the cultivation of A. niger, the largest endo-PG activity (80.6 U.g-1) was obtained in a process condition that allowed that the temperature reached values close to 45ºC. When the medium temperature was controlled at 30ºC, the endo-PG activity was substantially lower, 46.4 U.g-1. In the tests with the model process, no clearly positive influence of agitation on the production of endo-PG was observed. From the temperature-controlled experiments however, it is possible to suggest that endo-PG formation is favored by a stress condition for the microorganism, represented in this case by medium temperatures over 40ºC, since the optimal temperatures for A. niger growth is found in the range of 28 to 34ºC. This result disagrees from what is generically described in the specialized literature for the solid state cultivations, being this fact an example of the importance of having a small-scale rotating-drum bioreactor as a basic equipment for fundamental studies on that type of fermentative process. Additionally, the fact of the reactor body being built on glass allows the inspection of the internal space of the rotating drum and to observe the effects of agitation on the cultivation medium.

A study was conducted to determine the dependency of sound attenuation capabilities of earmuffs and earcaps on various application instruction techniques including: (1) no instruction, (2) no instruction with 70 dBA auditory feedback, (3) manufacturers' package instruction, (4) detailed instruction, and (5) modeled instruction. The hearing protection devices (HPDs) studied were: two earcaps (Willson #20 Sound-Ban, Flents #055 Peace & Quiet Headband), and four earmuffs (E-A-R model 1000, Siebe Norton Industrial model 4540, Peltor H6A/v, and Willson 365A Sound Barrier). HPD comfort and wearer preferences were also assessed. Furthermore, typical excessive industrial machinery noises were sampled and analyzed across the 1/3 octave frequencies. Finally, an example is provided as to how these machinery noise spectra can be matched with HPD attenuation spectra to ascertain the protector which would afford optimal protection for a given noise situation. Fifty subjects (twenty-five males and twenty-five females) participated in the experiment. Attenuation characteristics of the HPDs were evaluated utilizing the real-ear attenuation at threshold (REAT) method. A three-way mixed factorial design was used for data collection and analysis of attenuation results. Bipolar scales were used to assess individual HPD comfort, and the HPDs examined were ranked to obtain user preferences. In the analysis of attenuation results, analysis of variance CANOVA) and pairwise comparisons were utilized to detect statistical significance. The comfort scales and ranking scores were evaluated using the Friedman one-way block design. Attenuation results for the earmuffs and earcaps tested showed that they were much less susceptible than earplugs (from a previous study by Epps, 1984) to changes in user insertion/donning instruction technique and also not as dependent on user gender. The main effect of gender was not significant, and in general, any instruction was better than no instruction at all but the effects of those instructions did not differ significantly among each other. As expected, there were main effect differences among the HPDs as to their attenuation capabilities, rated discomfort, and user preference. Because the main objective was on assessing donning instruction effects on HPD attenuation, the comfort/preference assessment was based on only a short (25 minutes) wearing time during the attenuation tests. Therefore, the comfort/preference ratings could likely vary given longer wearing periods and different work environments. All results found are discussed on the basis of the sample data obtained and conclusions drawn from these results should be limited to these experimental conditions and subsequent analyses, as actual attenuation achieved in practice may differ. The example of HPD-machinery noise matching illustrates that the attenuation/spectral matching procedure may indeed be a feasible way of selecting optimal protection for workers.
Master of Science

Thesis (PhD) -- University of Western Sydney, 2003.
A thesis submitted to the University of Western Sydney in partial fulfillment of the requirements for the degree of Doctor of Philosophy. Includes references pp.191 - 202, and appendices.

Thesis (MScEng) Stellenbosch University, 2014
ENGLISH ABSTRACT: Teleoperation as a field has seen much change since its inception in the early 1940s with Dr. Raymond Goertz producing the first teleoperation system for manipulating radioactive materials. With advances in core and supporting technologies, the systems have grown in complexity and capability, allowing users to perform tasks anywhere in the world irrespective of physical distance. The feasibility of such systems has increased as the drive for use of telepresence robots, exploration robots as in space exploration, search and rescue robots and military systems such as UAVs and UGVs gain popularity. This prompted the development of a proof of concept modular, user centred telerobotic system. The current project is the second iteration in the development process. Teleoperation and more specifically telerobotic systems pose a challenge for many system developers. This may be a result of complexity or the wide assortment of knowledge areas that developers must master in order to deliver the final system. Developers have to balance system usability, user requirements, technical design and performance requirements. Several developmental process models are considered in context of Engineering Management (EM). A larger Systems Engineering developmental process is used, with focus on the primary and supportive EM components. The author used a hybrid developmental model that is user focussed in its approach, the User-Centred Systems Design (UCSD) methodology was adopted as the primary model for application within the two distinct developmental categories. The first category hardware and system integration utilised the UCSD model as is. The second - Software development - relied on the use of agile models, rapid application development (RAD) and extreme programming (XP) were discussed with XP being chosen as it could easily incorporate UCSD principles in its development process. Hardware systems development consisted of mechanical design of end-effectors, configuration management and design, as well as haptic and visual feedback systems design for the overall physical system. Also included is the physical interface design of the input (master) cell. Further software development was broken into, three sections, the first and most important was the graphical user interface, haptic control system with kinematic model and video feedback control. The force following and matching characteristics of the system were tested and were found to show an improvement over the previous implementation. The force magnitude error at steady state was reduced by 10%. While there was a dramatic improvement in system response, the rise time was reduced by a factor 10. The system did however show a decrease in angular accuracy, which was attributed to control system limitations. Further human-factor analysis experiments were conducted to test the system in two typical use-case scenarios. The first was a planar experiment and the second a 3D placement task. The factors of interest identified were field-of-view, feedback vision mode, and input modality. Heuristic performance indicators such as time-to-completion and number of collisions for a given task were measured. System performance was only showed significant improvement when used with haptic control. This shows that the research into haptic control systems will prove to be valuable in producing usable systems. The vision factor analysis failed to yield significant results, although they were useful in the qualitative systems analysis. The feedback from post-experimentation questionnaires showed that users prefer the Point of View as a field of view and 2D viewing over 3D viewing, while the haptic input modality was preferred. The results from the technical verification process can be used in conjunction with insights gained from user preference and human-factor analysis to provide guidance for future telerobotic systems development at Stellenbosch University.
AFRIKAANSE OPSOMMING: Telewerksverigting as ’n gebied het al vele veranderinge ondergaan vandat die eerste stelsels deur Dr. Raymond Goertz geimplementeer was in die vroeë 1940s vir die hantering van radioaktiewe materiale. Met vordering in kern en ondersteunende tegnologieë, het die telewerksverigtingstelsels toegeneem in kompleksiteit asook gevorder in vermoeënsvaardigheid, wat gebruikers in staat stel om take te verrig vanuit enige plek op aarde, ongeag die fisiese afstand wat die gebruiker en die werksarea skei. Die lewensvatbaarheid van hierdie stelsels het ook toegeneem weens die belangstelling in teleteenwoordigheidrobotte, ruimtevaardige-robotte, reddings-robotte en militêre-robotte soos onbemandelug- voertuie (OLV) en onbemande-grond-voertuie(OGV). As gevolg van die belangstelling in telerobotiese stelsels is die ontwikkeling van ’n modulêre, gebruikers-gesentreerde telewerksverigting stelsel onderneem. Die huidige projek is ’n tweede iterasie hiervan. Telewerksverigting, en meer spesifiek, telerobotika stelsels ontwikelling, vereis dat stelselontwikkelaars ’n verskeidenheid kennisareas bemeester. Die ontwikkelaar moet ’n belans vind tussen gebruiker vereistes, bruikbaarheid asook tegniese ontwerp en prestasie vereistes. Menigde ontwikkelingsproses modelle is oorweeg en behandel in die konteks van Ingenieursbestuur (IB). ’n Stelselsontwikkeling proses is gevolg met ’n fokus op primêre en ondersteunende IB komponente. ’n Gemengde ontwikkeling is toegepass tot die projek wat die gebruiker as ’n hoof komponent van die stelsel in ag neem. Die oorhoofse ontwikkelingsmodel is die User-centred Systems Design (UCSD) proses, wat vir beide hardeware en sagteware ontwikkeling gebruik is. Vir die hardeware ontwikkeling is die UCSD toegepas soos dit uiteengesit is in die literatuur. Die sagteware ontwikkeling is voltooi met behulp van ratse metodes, “Rapid Application Development” RAD en “Extreme Programming” (XP) was oorweeg en XP was gekies as ontwikkelingsmodel. XP was die natuurlike keuse weens die gemak waarmee UCSD metodes en prinsiepe kon geinkorporeer word in die ontwikkelings proses. Hardeware onwikkeling het bestaan uit meganiese ontwerp, manipulasiegereedskap ontwerp, konfigurasie bestuur en ontwikkeling asook haptiese en visueleterugvoer stelselsontwerp van die fisiese stelsel insluitend die fisiese koppelvlakontwerp van die meester sel. Verder is sagtewareontwerp opgedeel in ’n haptiesebeheerstel met ’n kinematiese model ontwikkeling, videoterugvoerbeheer en gebruikersintervlak ontwerp. Die vermoëe van die stelsel om krag insette na te boots was verbeter met ’n gestadigde verbetering van 10%. Die reaksietyd van die stelsel is verbeter met ’n faktor van 10. Die stelsel het ’n verswakking getoon in die algehele hoekakkuraatheid, die oorsprong van die verswakking kan aan die beheerstelsel teogeken word. Verdere menslikefaktoranalise eksperimente is voltooi om die stelsel in twee tipiese gebruikgeval scenario’s te toets. Die eerste, ’n platvlak-eksperiment en die tweede ’n 3D plasingingstaak eksperiment. Die faktore van belang is ïdentifiseer as, visie-veld, terugvoervisie modus en insette modaliteit. Heuristiese prestasie-aanwysers soos tyd-tot-voltooiing en die aantal botsings vir ’n gegewe taak is gemeet. Stelselprestasie het slegs aansienlike verbetering getoon wanneer die stelsel met die haptiesebeheer modus bedryf word. Die visiefaktor ontleding het geen noemenswaardige resultate opgelewer nie. Terugvoervorms was na elke eksperiment voltooi. Vraelyste het getoon dat gebruikers die oogpunt van ’n lae hoek en 2D video oor 3D video verkies, terwyl die haptic beheer modaliteit verkies word.

The petroleum industry has one of the most complex supply chains in the world. A unique characteristic of Petroleum Supply Chain (PSC) is the high degree of uncertainty which propagates through the network. Therefore, it is necessary to develop quantitative models aiming at optimizing the network and managing logistics operations. This work proposes a deterministic Mixed Integer Linear Program (MILP) model for downstream PSC to determine the optimal distribution center (DC) locations, capacities, transportation modes, and transfer volumes. Three products are considered in this study: gasoline, diesel, and jet fuel. The model minimizes multi-echelon multi-product cost along the refineries, distribution centers, transportation modes and demand nodes. The relationship between strategic planning and multimodal transportation is further elucidated. Furthermore, this work proposes a two stage Stochastic Mixed Integer Linear Program (SMILP) models with recourse for PSC under the risk of random disruptions, and a two stage Stochastic Linear Program (SLP) model with recourse under the risk of anticipated disruptions, namely hurricanes. Two separate types of mitigation strategies ? proactive and reactive ? are proposed in each model based on the type of disruption. The SMILP model determines optimal DC locations and capacities in the first stage and utilizes multimode transportation as the reactive mitigation strategy in the second stage to allocate transfer volumes. The SLP model uses proactive mitigation strategies in the first stage and employs multimode transportation as the reactive mitigation strategy. The goal of both stochastic models is to minimize the expected total supply chain costs under uncertainty. The proposed models are tested with real data from two sections of the U.S. petroleum industry, PADD 3 and PADD 1, and transportation networks within Geographic Information System (GIS). It involves supply at the existing refineries, proposed DCs and demand nodes. GIS is used to analyze spatial data and to map refineries, DCs and demand nodes to visualize the process. Sensitivity analysis is conducted to asses supply chain performance in response to changes in key parameters of proposed models to provide insights on PSC decisions, and to demonstrate the impact of key parameters on PSC decisions and total cost.
Upper Great Plains Transportation Institute (UGPTI)
Mountain Plains Consortium (MPC)

A constante mudança nos meios de trabalho ocorre devido a evolução tecnológica e industrial. Entretanto, com o advento de tais inovações, dificilmente o trabalhador da indústria não é submetido aos mais variados riscos ocupacionais resultantes dos processos produtivos. Diante deste contexto, o presente estudo teve como objetivo principal avaliar os níveis de vibração e de ruído aos quais os trabalhadores de uma empresa do setor da construção civil, especializada na manutenção e reformas de pisos industriais, estavam expostos durante suas jornadas de trabalho em duas frentes de trabalho. As medições foram realizadas em locais e dias distintos nos municípios de Curitiba e de São José dos Pinhais, ambos no estado do Paraná. Para a avaliação da vibração ocupacional, utilizou-se um acelerômetro junto ao trabalhador e um sensor triaxial acoplado na empunhadura dos equipamentos objeto de estudo, que foram duas diferentes fresadoras de piso. Posteriormente os dados foram processados e comparados com o novo texto do Anexo no 08 da Norma Regulamentadora NR-15, apresentado para consulta pública pelo Ministério do Trabalho e Emprego entre os meses de janeiro e fevereiro de 2014. Já para a medição do ruído utilizou-se um dosímetro de ruído junto ao trabalhador, cujo resultado final possibilitou a comparação com o Anexo no 01 da mesma Norma Regulamentadora. Os resultados finais indicaram níveis de exposição excessivos, superiores aos limites de tolerância determinados pela Legislação, tanto para vibração quanto para o ruído, gerando insalubridade para os trabalhadores expostos, em todos os locais onde foram realizadas as medições.
The constant change in the means of work is done by technological and industrial developments. However, with the advent of such innovations, hardly the work of the industry is not subject to a variety of occupational hazards resulting from production processes. Given this context, the present study aimed to monitor the working hours of the employees of a company in the construction industry, specializing in industrial floor maintenance and renovations, as exposure of vibration and noise on two fronts work in the cities of Curitiba - PR and São José dos Pinhais – PR. The program took place in two locations and on different days. The workday adopted by the company is six hours daily. For the evaluation of vibration, we used accelerometer with the worker and coupled to the handle of the equipment object of study, a mill floor, triaxial sensor subsequently the data were processed and compared with the new text of Annex No. 08, NR 15, submitted for public consultation by the Ministry of Labour and Employment in the months of January and February 2014. As for noise measurement used a dosimeter with the worker, whose final results enabled comparison with the regulatory norm 15 - Annex No. 01. The final results indicate excessive exposure to the tolerance specified by the legislation, both vibration and sound pressure level, featuring unhealthy at all locations where measurements were performed.

Certain applications have recently appeared in industry where a traditional bar code printed on a label will not survive because the item to be tracked has to be exposed to harsh environments. Laser direct-part marking is a manufacturing process used to create permanent marks on a substrate that could help to alleviate this problem. In this research, a 532 nm laser was utilized to create a direct-part marked Data Matrix symbol onto carbon steel substrates with different carbon content. The quality of the laser marked Data Matrix symbol was then evaluated according to the criteria outlined in the ISO/IEC 16022 bar code technology specification for Data Matrix. Several experiments were conducted to explore the effects that different parameters have on the quality of the laser direct-part marked symbols. First, an experiment was conducted to investigate the effect of two different laser tool path patterns. In later experiments, parameters such as type of carbon steel, percent of laser tool path overlap, profile speed, average power and frequency were found to have significant effects on the quality of laser direct-part marked Data Matrix symbols. The analysis of the results indicated that contrast and print growth were the critical standard performance measures that limited laser direct-part marked Data Matrix symbols from achieving a higher final grade. No significant effects were found with respect to other standard performance measures (i.e., encode, axial uniformity, and unused error correction). Next, the experimental data collected for contrast and print growth was utilized as training, validation and testing data sets in the modeling of artificial neural networks for the laser direct-part marking process. Two performance measures (i.e., mean squared error and correlation coefficient) were employed to assess the performance of the artificial neural network models. Single-output artificial neural network models corresponding to a specific performance measure were found to have good learning and predicting capabilities. The single-output artificial neural network models were compared to equivalent multiple linear regression models for validation purposes. The prediction capability of the single-output artificial neural network models with respect to laser direct-part marking of Data Matrix symbols on carbon steel substrates was superior to that of the multiple linear regression models.
Graduation date: 2004

Feeding the men and animals of the Army of Tennessee required thousands of tons of food to be transported by wagon, train, and steamboat. In addition to transportation, feeding the army proved difficult because its food supply had to be shared with other branches of the Confederate Army. Soldiers often complained of monotonous rations. Capt. Moses H. Wright’s Atlanta Arsenal supplied most of the Army of Tennessee’s ammunition. However, the Atlanta Arsenal struggled to keep up with demand, and army personnel complained about defective equipment. An attempt to uniformly equip soldiers with weapons ultimately failed. The Atlanta Quartermaster Depot made shoes exclusively for the Army of Tennessee. This depot also made clothing for the army. Shortages of clothing and shoes persisted. The Army of Tennessee relied on the Western & Atlantic railroad to transport materials from Atlanta, which at times did not have enough engines to provide adequate supplies. Overall, the Army of Tennessee had industrial assets, but an inadequate transportation system led to meat shortages, which decreased morale and resulted in desertions. Additionally, the poor transportation system prevented additional troops from reaching the disastrous Battle of Chickamauga.