Log in

Relevant bibliographies by topics / Layer Performance

Contents

Journal articles
Dissertations / Theses
Books
Book chapters
Conference papers
Reports

Academic literature on the topic 'Layer Performance'

Author: Grafiati

Published: 3 June 2025

Last updated: 31 July 2025

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles

Select a source type:

Consult the lists of relevant articles, books, theses, conference reports, and other scholarly sources on the topic 'Layer Performance.'

Next to every source in the list of references, there is an 'Add to bibliography' button. Press on it, and we will generate automatically the bibliographic reference to the chosen work in the citation style you need: APA, MLA, Harvard, Chicago, Vancouver, etc.

You can also download the full text of the academic publication as pdf and read online its abstract whenever available in the metadata.

Journal articles on the topic "Layer Performance"

1

Sun, Min, and Ming Pang. "Defect Formation Mechanism and Performance Study of Laser Cladding Ni/Mo Composite Coating." Coatings 11, no. 12 (2021): 1460. http://dx.doi.org/10.3390/coatings11121460.

Full text

Abstract:

In order to improve the wear resistance of Cu, a Ni/Mo composite coating was applied on the surface of Cu alloy by means of laser cladding. The laser power was 6000 W, the scanning speed was 5 mm/s and the feed rate was 10 g/min. The transition layer of the Ni layer had three layers, and the surface layer of the Mo layer had two layers. The results showed that the surface of the cladding layer was pure Mo. Due to the fluidity and non-equilibrium solidification of Mo in the molten state, pores and cracks along the grain boundary were observed in the Mo layer. The results showed that the cross-s

APA, Harvard, Vancouver, ISO, and other styles

2

Hossain, Md Sajid, and Dewan Mohammed Abdul Ahad. "Performance Analysis of Modulation Response of a Designed 1550 nm Oxide Confined Vertical Cavity Surface Emitting Laser." AIUB Journal of Science and Engineering (AJSE) 17, no. 3 (2018): 83–88. http://dx.doi.org/10.53799/ajse.v17i3.13.

Full text

Abstract:

This paper aims to present the impact of using oxidized layer and the effect of oxide aperture size on VCSEL’s modulation performance. After the introduction of oxidized layer, the characteristics of VCSEL have improved immensely, especially in modulation performance. The peak material gain of Al0.06Ga0.24In0.70As/InP MQW VCSEL found from the MATLAB simulation tools has been utilized for investigating the modulation characteristics of the laser model. The optical output power of 27.23 dBm is found at 2.5 mA of current injection. Later, by varying the injection current up to 2.5 mA a maximum fr

APA, Harvard, Vancouver, ISO, and other styles

3

Bonek, Mirołsaw, and Leszek Adam Dobrzański. "Characterization Performance of Laser Melted Commercial Tool Steels." Materials Science Forum 654-656 (June 2010): 1848–51. http://dx.doi.org/10.4028/www.scientific.net/msf.654-656.1848.

Full text

Abstract:

The purpose of this research paper is focused on the X40CrMoV5-1 hot work tool steel surface layers improvement properties using high power diode laser. In the effect of laser alloying with powders of carbides occurs size reduction of microstructure, as well as dispersion hardening through fused in but partially dissolved carbides and consolidation through enrichment of surface layer in alloying additions coming from dissolving carbides. Introduced particles of carbides and in part remain undissolved, creating conglomerates being a result of fusion of undissolved powder grains into molten meta

APA, Harvard, Vancouver, ISO, and other styles

4

Xin, S., K. F. Longenbach, and W. I. Wang. "AlGaAs–GaAs–InGaAs strained layer laser structure with performance independent of AlGaAs layer quality." Electronics Letters 27, no. 3 (1991): 199. http://dx.doi.org/10.1049/el:19910129.

Full text

APA, Harvard, Vancouver, ISO, and other styles

5

Qi, Saren, Weiyi Li, Yang Zhao, et al. "Influence of the properties of layer-by-layer active layers on forward osmosis performance." Journal of Membrane Science 423-424 (December 2012): 536–42. http://dx.doi.org/10.1016/j.memsci.2012.09.009.

Full text

APA, Harvard, Vancouver, ISO, and other styles

6

Cao, Yang, Chenye Yuan, Yanchao Zhang, and Jun Ma. "Laser Cladding Performance and Process Parameter Optimization for Fe90 Alloy." Metals 14, no. 12 (2024): 1432. https://doi.org/10.3390/met14121432.

Full text

Abstract:

Fe90 alloy has a high weld hardness, good toughness, and high oxidation resistance, and is often used as a cladding material to repair the surfaces of 42CrMo steel structures of large shearer picks. The influence of the laser cladding processing parameters on the microstructure, properties, and formation mechanism of Fe90 alloy layers on the surface of 42CrMo steel was studied. Simulations were conducted to investigate how these processing parameters affect the temperature field and internal stress of the cladding layer. A complex nonlinear relationship between variables and residual stresses

APA, Harvard, Vancouver, ISO, and other styles

7

Yu, Yuelong, Min Zhang, Yingchun Guan, et al. "The Effects of Laser Remelting on the Microstructure and Performance of Bainitic Steel." Metals 9, no. 8 (2019): 912. http://dx.doi.org/10.3390/met9080912.

Full text

Abstract:

The surface of bainitic steel was remelted by fiber laser, and the microstructure and mechanical properties of the melted layer were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), a nanoindentation instrument, and wear equipment. The study of changing the laser scanning speed showed that the depth of the melted layer increases with decreases of the laser scanning speed. The wear-resistance property increased by 55% compared with the matrix and decreased with the reduction of laser scanning speed within a certain range. In the study of changing the laser-

APA, Harvard, Vancouver, ISO, and other styles

8

Li, Yun Tao, Fei Xiang Jin, Ning Xu Wang, Qing Chang, and De Yu Liu. "The Influence of GGG70L Laser Surface Hardening Power on Quenched Layer Performance." Advanced Materials Research 774-776 (September 2013): 1051–54. http://dx.doi.org/10.4028/www.scientific.net/amr.774-776.1051.

Full text

Abstract:

GGG70L die material laser phase change hardening aims to discover the Quenched Layer performance of the GGG70L die material hardened by the laser of different power. Making comparison and analysis in the experiment and considering the actual production factors such as cost, working efficiency and product quality standard, it is concluded that laser power being 1900 w, laser scanning speed 6mm/s, spot size 3×15 mm2, focal length being 305mm, the surface of the material quality can meet the requirements of industrial production, laser surface quenched layer becomes harder, good abrasion resistan

APA, Harvard, Vancouver, ISO, and other styles

9

Henriksen, N. G., O. Z. Andersen, M. S. Jellesen, T. L. Christiansen, and M. A. J. Somers. "Influence of Laser Marking on Microstructure and Corrosion Performance of Martensitic Stainless Steel Surfaces for Biomedical Applications." HTM Journal of Heat Treatment and Materials 77, no. 3 (2022): 177–96. http://dx.doi.org/10.1515/htm-2022-1010.

Full text

Abstract:

Abstract The medical device industry demands unique device identification (UDI) tags on metallic components applied via laser marking. A common issue is that the visual appearance of the marking becomes poorly legible over time due to loss of contrast. Nanosecond pulsed laser irradiation was used to grow an oxide layer on two different martensitic stainless steels AISI 420F mod and 420B to compare the influences of the chemical composition of the steel (with and without S), power density, and energy input. The corrosion behavior was found to depend strongly on laser energy input. The presence

APA, Harvard, Vancouver, ISO, and other styles

10

You, Minghui, Qixiang Sun, Liping Yin, et al. "2.3 µm InGaAsSb/AlGaAsSb Quantum-Well Laser Diode via InAs/GaSb Superlattice Layer on GaAs Substrate." Journal of Nanomaterials 2016 (2016): 1–4. http://dx.doi.org/10.1155/2016/8393502.

Full text

Abstract:

We present 2.3 μm InGaAsSb/AlGaAsSb type I laser diodes (LDs) on GaAs substrate; a superlattice (SL) layer was introduced as an interconnecting layer playing an important role in manipulating the optical field distribution and reducing free-carrier absorption in multiquantum wells (MQWs) for achieving balanced and optimal LDs performance. Accordingly, power of 8.6 mW was obtained with 2.3 μm wavelength. Our results demonstrate that superlattice layer may open a new avenue for high performance and improvement in mid-infrared laser diode.

APA, Harvard, Vancouver, ISO, and other styles

More sources

Dissertations / Theses on the topic "Layer Performance"

1

Kunkel, Julian Martin. "Performance Analysis of the PVFS2 Persistency Layer." [S.l. : s.n.], 2006. http://nbn-resolving.de/urn:nbn:de:bsz:16-opus-63302.

Full text

APA, Harvard, Vancouver, ISO, and other styles

2

Karlsson, Jonas. "Transport-Layer Performance in Wireless Multi-Hop Networks." Doctoral thesis, Karlstads universitet, Institutionen för matematik och datavetenskap, 2013. http://urn.kb.se/resolve?urn=urn:nbn:se:kau:diva-15603.

Full text

Abstract:

Wireless communication has seen a tremendous growth in the last decades. Continuing on this trend, wireless multi-hop networks are nowadays used or planned for use in a multitude of contexts, spanning from Internet access at home to emergency situations. The Transmission Control Protocol (TCP) provides reliable and ordered delivery of a data and is used by major Internet applications such as web browsers, email clients and file transfer programs. TCP traffic is also the dominating traffic type on the Internet. However, TCP performs less than optimal in wireless multi-hop networks due to packe

APA, Harvard, Vancouver, ISO, and other styles

3

Chen, Cheng. "Performance evaluation of optimized physical layer network coding." Thesis, University of York, 2017. http://etheses.whiterose.ac.uk/18913/.

Full text

Abstract:

With the development of the wireless networks these years, devices are required to have an even higher data rate, and thus the interference between devices remains a significant problem to be solved. In order to secure a reliable transmission with- out wasting network capacity, we would necessarily select a proper transmission scheme. The Physical layer Network Coding (PNC) , is one of the optimum choices as it can increase the efficiency largely, especially in a system with 2 users and 1 relay (TWRC). Generally speaking, we may divide our research into two aspects: channel and channel coding.

APA, Harvard, Vancouver, ISO, and other styles

4

Plas, Angélique (Angélique Pascale). "Performance of a boundary layer ingesting propulsion system." Thesis, Massachusetts Institute of Technology, 2006. http://hdl.handle.net/1721.1/35568.

Full text

Abstract:

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Aeronautics and Astronautics, 2006.<br>Includes bibliographical references (p. 111-114).<br>This thesis presents an assessment of the aerodynamic performance of an aircraft propulsion system, with embedded engines, in the presence of aircraft fuselage boundary layer ingestion (BLI). The emphasis is on defining the role that the turbomachinery (i.e., the fan, in the ultra high bypass engines considered) plays in establishing the flow benefit due to BLI. A three-dimensional body force approach to fan response to inlet distortion has

APA, Harvard, Vancouver, ISO, and other styles

5

Breitfeld, Oliver. "Improving the performance of aerofoil sections using momentum transfer via a secondary flow." Thesis, University of South Wales, 2002. https://pure.southwales.ac.uk/en/studentthesis/improving-the-performance-of-aerofoil-sections-using-momentum-transfer-via-a-secondary-flow(a3627a17-2b56-4e3a-9c73-64e0e105f3d6).html.

Full text

Abstract:

Aerodynamic flow control can improve aerofoil performance by influencing the natural growth of boundary layers, which develop on the surface of vehicles moving in viscous fluids. Many active and passive techniques have been developed to reduce drag and/or increase the lift of aerofoil sections. The work presented in this thesis is concerned with the active excitation of the boundary layer on the suction side of aerofoil sections through momentum transfer via a secondary flow. The secondary flow was achieved by air passing through an air breathing device (ABD) which was implemented in the aerof

APA, Harvard, Vancouver, ISO, and other styles

6

Berezin, Maria Eugenia. "Cross-layer techniques for Wireless Local Area Networks." Thesis, Grenoble, 2013. http://www.theses.fr/2013GRENM069/document.

Full text

Abstract:

Dans cette thèse, nous examinons les aspects essentiels des réseaux locaux sans fil IEEE 802.11 (réseaux WiFi) en mode infrastructure, et identifions les problèmes qui peuvent affecter leurs performances. Après avoir étudié l'état de l'art, nous constatons que de nombreux efforts de recherche ont proposé des solutions diverses mais présentant des limitations qui empêchent leur déploiement dans les réseaux locaux sans fil existants. En outre, les utilisateurs de ces réseaux ont des attentes toujours croissantes de disponibilité, de fiabilité, de réponse instantanée et de sécurité de la part de

APA, Harvard, Vancouver, ISO, and other styles

7

Bandaru, Rammohan, and Debashis Barman. "Performance Evaluation of SCTP as a Transport Layer Protocol." Thesis, Högskolan i Halmstad, Sektionen för Informationsvetenskap, Data– och Elektroteknik (IDE), 2011. http://urn.kb.se/resolve?urn=urn:nbn:se:hh:diva-16003.

Full text

Abstract:

TCP and UDP are the most popular transport protocols used for end-end data transmission. The rapid growth of internet leads to development of many innovative applications in the current environment. Depending on the functionality of these applications, requirements of transport protocols are changing. TCP is known for its problems with Head Of Line blocking (HOL) and SYN attacks which gives reduced performance, and also doesn’t support Multi-Homing. SCTP is another transport layer protocol similar to TCP which provides end-end communication. It has some unique features like support for Multi-h

APA, Harvard, Vancouver, ISO, and other styles

8

Vitsas, Vasileios. "Link layer protocol performance of indoor infrared wireless communications." Thesis, Bournemouth University, 2002. http://eprints.bournemouth.ac.uk/305/.

Full text

Abstract:

The increasing deployment of portable computers and mobile devices leads to an increasing demand for wireless connections. Infrared presentsseveral advantagesover radio for indoor wireless connectivity but infrared link quality is affected by ambient infrared noise and by low power transmission levels due to eye safety limitations. The Infrared Data Association (IrDA) has developed the widely used IrDA 1.x protocol standard for short range, narrow beam, point to point connections.IrDA addressedthe requirement for indoor multipoint connectivity with the development of the Advanced Infrared (AIr

APA, Harvard, Vancouver, ISO, and other styles

9

Tay, Hui Min June. "Improving end system performance using a robust link layer." Thesis, University of Aberdeen, 2003. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.274856.

Full text

Abstract:

A software-based modem design offers a new opportunity to integrate processing at various levels, to enhance performance (TCP throughput) and robustness (to jamming). There are several key problems that need to be addressed that impact link ARQ performance. ACKs are needed for link sender to retransmit or adapt and an imperfection of ACK feedback from receiver prevents a link responding to loss and may cause the forwarding to be suspended. Another problem identified is that although ARQ may efficiently retransmit corrupted frames resulting from Partial Band Noise Jamming, it is inefficient whe

APA, Harvard, Vancouver, ISO, and other styles

10

JOSHI, TARUN. "CROSS LAYER OPTIMIZATIONS FOR PERFORMANCE ENHANCEMENT OF WIRELESS NETWORKS." University of Cincinnati / OhioLINK, 2006. http://rave.ohiolink.edu/etdc/view?acc_num=ucin1159560622.

Full text

APA, Harvard, Vancouver, ISO, and other styles

More sources

Books on the topic "Layer Performance"

1

Srivastava, ManMohan, ed. High-Performance Thin-Layer Chromatography (HPTLC). Springer Berlin Heidelberg, 2011. http://dx.doi.org/10.1007/978-3-642-14025-9.

Full text

APA, Harvard, Vancouver, ISO, and other styles

2

Srivastava, M. M. High-Performance Thin-Layer Chromatography (HPTLC). Springer-Verlag Berlin Heidelberg, 2011.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

3

United States. National Aeronautics and Space Administration., ed. Performance of renormalization group algebraic turbulence model on boundary layer transition simulation. National Aeronautics and Space Administration, 1994.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

4

Vitsas, Vasileios. Link layer protocol performance of indoor infrared wireless communications. Bournemouth University, 2002.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

5

United States. National Aeronautics and Space Administration., ed. Comparison of two procedures for predicting rocket engine nozzle performance. National Aeronautics and Space Administration, 1987.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

6

Anne, Schibli, ed. High-performance thin-layer chromatography for the analysis of medicinal plants. Thieme, 2007.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

7

Fisher, S. A. Internal performance of a variable ramp mixed compression intake at Mach 3.05. Aeronautical Research Laboratories, 1985.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

8

Johnson, Steven. Pressure-sensing performance of upright cylinders in a Mach-10 boundary layer. National Aeronautics and Space Administration, Office of Management, Scientific and Technical Information Program, 1994.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

9

Johnson, Steven A. Pressure-sensing performance of upright cylinders in a Mach-10 boundary layer. National Aeronautics and Space Administration, Office of Management, Scientific and Technical Information Program, 1994.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

10

Kelly, Murphy, and United States. National Aeronautics and Space Administration. Scientific and Technical Information Program., eds. Pressure-sensing performance of upright cylinders in a Mach-10 boundary layer. National Aeronautics and Space Administration, Office of Management, Scientific and Technical Information Program, 1994.

Find full text

APA, Harvard, Vancouver, ISO, and other styles

More sources

Book chapters on the topic "Layer Performance"

1

Holma, Harri, Jussi Reunanen, Leo Chan, et al. "Physical Layer Performance." In WCDMA for UMTS. John Wiley & Sons, Ltd, 2005. http://dx.doi.org/10.1002/0470870982.ch12.

Full text

APA, Harvard, Vancouver, ISO, and other styles

2

Holma, Harri, Jussi Reunanen, Leo Chan, et al. "Physical Layer Performance." In WCDMA for UMTS. John Wiley & Sons, Ltd, 2010. http://dx.doi.org/10.1002/9780470669501.ch11.

Full text

APA, Harvard, Vancouver, ISO, and other styles

3

Ali-Yahiya, Tara. "LTE Phyiscal Layer." In Understanding LTE and its Performance. Springer New York, 2011. http://dx.doi.org/10.1007/978-1-4419-6457-1_4.

Full text

APA, Harvard, Vancouver, ISO, and other styles

4

Holt, Alan, and Chi-Yu Huang. "MAC Layer Performance Analysis." In Computer Communications and Networks. Springer London, 2010. http://dx.doi.org/10.1007/978-1-84996-275-9_9.

Full text

APA, Harvard, Vancouver, ISO, and other styles

5

Ali-Yahiya, Tara. "LTE Radio Layer Design." In Understanding LTE and its Performance. Springer New York, 2011. http://dx.doi.org/10.1007/978-1-4419-6457-1_3.

Full text

APA, Harvard, Vancouver, ISO, and other styles

6

Kaufmann, Michael, Paul Molitor, and Wolfgang Vogelgesang. "Performance driven k-layer wiring." In STACS 92. Springer Berlin Heidelberg, 1992. http://dx.doi.org/10.1007/3-540-55210-3_207.

Full text

APA, Harvard, Vancouver, ISO, and other styles

7

Milojković-Opsenica, Dušanka, and Filip Andrić. "High Performance Thin-Layer Chromatography." In Green Chromatographic Techniques. Springer Netherlands, 2013. http://dx.doi.org/10.1007/978-94-007-7735-4_4.

Full text

APA, Harvard, Vancouver, ISO, and other styles

8

Ötles, Semih, and Vasfiye Hazal Özyurt. "High-Performance Thin-Layer Chromatography." In Analysis of Naturally Occurring Food Toxins of Plant Origin. CRC Press, 2022. http://dx.doi.org/10.1201/9781003222194-15.

Full text

APA, Harvard, Vancouver, ISO, and other styles

9

Schobeiri, Meinhard T. "Introduction into Boundary Layer Theory." In Turbomachinery Flow Physics and Dynamic Performance. Springer Berlin Heidelberg, 2012. http://dx.doi.org/10.1007/978-3-642-24675-3_21.

Full text

APA, Harvard, Vancouver, ISO, and other styles

10

Ahlgren, Bengt. "A Performance Model for Integrated Layer Processing." In High Performance Networking VII. Springer US, 1997. http://dx.doi.org/10.1007/978-0-387-35279-4_16.

Full text

APA, Harvard, Vancouver, ISO, and other styles

Conference papers on the topic "Layer Performance"

1

Dempster, W. A., and J. D. Kellner. "High Performance Multi-Layer Anti-Corrosion Coating System." In CORROSION 1992. NACE International, 1992. https://doi.org/10.5006/c1992-92369.

Full text

Abstract:

Abstract A new hot-applied plant pipeline coating is described. The new multi-layer coating consists of three layers: A thermally activated primer layer; a crosslinked thermoplastic elastomer intermediate layer; and a fused polyolefin outer layer. A synergistic relationship arises between the three layers from their interaction during the application process. The heat of application initiates a reaction in the interfacial layers creating a completely fused coating system. This results in strong chemical and mechanical bonds that maximize the performance properties of the coating system. The pl

APA, Harvard, Vancouver, ISO, and other styles

2

Majerik, Filip, and Monika Borkovcova. "Performance Testing of Intelligent Data Layer." In 2024 IEEE 17th International Scientific Conference on Informatics (Informatics). IEEE, 2024. https://doi.org/10.1109/informatics62280.2024.10900775.

Full text

APA, Harvard, Vancouver, ISO, and other styles

3

Jiang, Zhiping, Choloong Hahn, Junho Chang, and Qingyi Guo. "New Performance Monitoring Capabilities at Physical Layer." In Optical Fiber Communication Conference. Optica Publishing Group, 2025. https://doi.org/10.1364/ofc.2025.m4a.2.

Full text

Abstract:

Optical performance monitoring is critical in optical network optimization and fault classification/localization. In this presentation, the emerging monitoring techniques, such as pilot tone-based, Rx-side LPM-based monitoring, and Rx-based fault diagnosis framework, are reviewed.

APA, Harvard, Vancouver, ISO, and other styles

4

Hofmann, Nikolai, Phillip Bogendörfer, Marc Stamminger, and Kai Selgrad. "Hierarchical multi-layer screen-space ray tracing." In HPG '17: High-Performance Graphics. ACM, 2017. http://dx.doi.org/10.1145/3105762.3105781.

Full text

APA, Harvard, Vancouver, ISO, and other styles

5

Kruse, Corey, Edwin Peng, Craig Zuhlke, et al. "Role of Copper Oxide Layer on Pool Boiling Performance With Femtosecond Laser Processed Surfaces." In ASME 2017 15th International Conference on Nanochannels, Microchannels, and Minichannels. American Society of Mechanical Engineers, 2017. http://dx.doi.org/10.1115/icnmm2017-5574.

Full text

Abstract:

Copper pool boiling surfaces are tested for pool boiling enhancement due to femtosecond laser surface processing (FLSP). FLSP creates self-organized micro/nanostructures on metallic surfaces and creates highly wetting and wicking surfaces with permanent surface features. In this study two series of samples were created. The first series consists of three flat FLSP copper surfaces with varying microstructures and the second series is an open microchannel configuration with laser processing over the horizontal surfaces of the microchannels. These microchannels range in height from 125 microns to

APA, Harvard, Vancouver, ISO, and other styles

6

Vidyasagar, L., and K. S. Latha Reddy. "Performance Evaluations of SSCOP Layer." In Joint International Conference on Autonomic and Autonomous Systems and International Conference on Networking and Services - (icas-isns'05). IEEE, 2005. http://dx.doi.org/10.1109/icas-icns.2005.75.

Full text

APA, Harvard, Vancouver, ISO, and other styles

7

Bestetti, A., G. Giambene, and S. Hadzic. "WiMAX: MAC layer performance assessments." In 2008 3rd International Symposium on Wireless Pervasive Computing (ISWPC). IEEE, 2008. http://dx.doi.org/10.1109/iswpc.2008.4556256.

Full text

APA, Harvard, Vancouver, ISO, and other styles

8

Sullivan, C. R., and Yuqin Sun. "Physically-based distributed models for multi-layer ceramic capacitors." In Electrical Performance of Electronic Packaging. IEEE, 2003. http://dx.doi.org/10.1109/epep.2003.1250028.

Full text

APA, Harvard, Vancouver, ISO, and other styles

9

Ullah, Shakeel Salamat, Soung Chang Liew, Lu Lu, and Lizhao You. "Physical-layer network coding: A high performance PHY-layer decoder." In ICC 2016 - 2016 IEEE International Conference on Communications. IEEE, 2016. http://dx.doi.org/10.1109/icc.2016.7511502.

Full text

APA, Harvard, Vancouver, ISO, and other styles

10

Fischer, Mathias, Sebastian Delling, Sascha Grau, and Guenter Schaefer. "Underlay-robust application layer multicast." In 2011 IEEE 30th International Performance Computing and Communications Conference (IPCCC). IEEE, 2011. http://dx.doi.org/10.1109/pccc.2011.6108100.

Full text

APA, Harvard, Vancouver, ISO, and other styles

Reports on the topic "Layer Performance"

1

Yang, Wen-Bin, and Michael Souryal. LTE physical layer performance analysis. National Institute of Standards and Technology, 2014. http://dx.doi.org/10.6028/nist.ir.7986.

Full text

APA, Harvard, Vancouver, ISO, and other styles

2

Wu, Q., Y. Yang, Y. Lee, D. Dhody, S. Randriamasy, and L. Contreras. Application-Layer Traffic Optimization (ALTO) Performance Cost Metrics. RFC Editor, 2023. http://dx.doi.org/10.17487/rfc9439.

Full text

APA, Harvard, Vancouver, ISO, and other styles

3

DeSantis, John, and Jeffery Roesler. Performance Evaluation of Stabilized Support Layers for Concrete Pavements. Illinois Center for Transportation, 2022. http://dx.doi.org/10.36501/0197-9191/22-003.

Full text

Abstract:

A research investigation was conducted on the erosion potential of stabilized subbases under concrete pavements and asphalt layers supporting concrete overlays. Through field surveys and testing in Illinois, this project evaluated if existing concrete pavements with stabilized subbases and concrete overlays were exhibiting potential erosion of the underlying support layer. The field evaluation testing included falling weight deflectometer testing, distress surveys, coring, and ultrasonic tomography scanning. A laboratory performance test was also established using the Hamburg wheel-tracking de

APA, Harvard, Vancouver, ISO, and other styles

4

Saadawi, Tarek. Optimizing Airborne Networking Performance with Cross-Layer Design Approach. Defense Technical Information Center, 2009. http://dx.doi.org/10.21236/ada502634.

Full text

APA, Harvard, Vancouver, ISO, and other styles

5

Coree, Brian, and Thomas White. Layer Coefficients in Terms of Performance and Mixture Characteristics. Purdue University, 1988. http://dx.doi.org/10.5703/1288284314152.

Full text

APA, Harvard, Vancouver, ISO, and other styles

6

Reid, Jeffrey S., Douglas L. Westphal, Richard M. Paulus, Si-Chee Tsay, and Alexander Van Eijk. Preliminary Evaluation of the Impacts of Aerosol Particles on Laser Performance in the Coastal Marine Boundary Layer. Defense Technical Information Center, 2004. http://dx.doi.org/10.21236/ada425811.

Full text

APA, Harvard, Vancouver, ISO, and other styles

7

Marshall, R. D. Performance requirements and preliminary design of a boundary layer wind tunnel facility. National Bureau of Standards, 1985. http://dx.doi.org/10.6028/nbs.ir.85-3168.

Full text

APA, Harvard, Vancouver, ISO, and other styles

8

Kim, Pum, Vlastimil Kunc, Bruno Turcksin, et al. Layer Time Control for Large Scale Additive Manufacturing Using High Performance Computing. Office of Scientific and Technical Information (OSTI), 2022. http://dx.doi.org/10.2172/1895216.

Full text

APA, Harvard, Vancouver, ISO, and other styles

9

Robinson, W. Full-scale evaluation of multi-axial geogrids in road applications. Engineer Research and Development Center (U.S.), 2022. http://dx.doi.org/10.21079/11681/43549.

Full text

Abstract:

The U.S. Army Engineer Research and Development Center (ERDC) constructed a full-scale unsurfaced test section to evaluate the performance of two prototype geogrids, referred to as NX950 and NX750, in road applications. The test section consisted of a 10-in.-thick crushed aggregate surface layer placed over a very weak 2 California Bearing Ratio (CBR) clay subgrade. Simulated truck traffic was applied using one of ERDC’s specially designed load carts outfitted with a single-axle dual wheel truck gear. Rutting performance and instrumentation response data were monitored at multiple traffic inte

APA, Harvard, Vancouver, ISO, and other styles

10

VAN LEEUWEN, BRIAN P., and MARK D. TORGERSON. Performance Impacts of Lower-Layer Cryptographic Methods in Mobile Wireless Ad Hoc Networks. Office of Scientific and Technical Information (OSTI), 2002. http://dx.doi.org/10.2172/805840.

Full text

APA, Harvard, Vancouver, ISO, and other styles

We offer discounts on all premium plans for authors whose works are included in thematic literature selections. Contact us to get a unique promo code!