Academic literature on the topic 'Light emiting diode'

<p>This master's thesis describe electromagnetic simulations of a gallium antimonide (GaSb) light emitting diode, LED. A problem for such devices is that most of the generated light is reflected from the surface due to total internal reflection, and is therefore prevented from coupling out of the semiconductor material. Etching out a 2D photonic crystal grating on the LED surface would put aside the absolute rule of total internal reflection, and could therefore be used to increase the total transmission. The simulation method which was developed was supposed to find geometry parameters for the photonic crystal to optimize the light extraction. A set of plane waves were therefore simulated using FDTD to build an equivalent to the Fresnel equations for the photonic crystal surface. From that the total transmittance and radiation patterns for the simulated geometries were calculated. The results indicated an increase in the transmission properties of up to 70% using a square grating of holes where the holes have a radius of 0.5µm, the hole depth is 0.4µm, and the grating constant is 1µm. A hexagonal grating of holes and a square grating of isotropically etched holes were also simulated, and featured improvements on the same scale, but with different dimensions for the holes. The simulations were computationally very demanding, and the simulation structure therefore had to be highly trimmed to limit the calculation time to reasonable values. This might have reduced the accuracy of the results. Especially the optimum grating constant, and the value of the optimum improvement itself is believed to be somewhat inaccurate.</p>

Les nanofils nitrures présentent des propriétés optoélectroniques extraordinaires et sont considérés comme des matériaux prometteurs pour des diodes électroluminescentes (LEDs), grâce à leur haute qualité cristalline, leurs surfaces non-polaires, leur bonne flexibilité mécanique, leur rapport d’aspect élevé, etc.Cette thèse adresse la croissance, la fabrication, les caractérisations optiques et électriques et la simulation optique des dispositifs à base de nanofils nitrures, avec un accent particulier sur les LEDs à nanofils.Premièrement, cette thèse présente la croissance par épitaxie en phase vapeur aux organométalliques de nanofils nitrures cœur-coquille auto-assemblés contenant des puits quantiques InGaN/GaN sur les facettes plan m avec différentes concentrations d’In. Puis est décrite la fabrication de LEDs utilisant ces nanofils suivant deux différentes stratégies d’intégration (intégrations planaires et verticales).L’intégration planaire est basée sur des nanofils uniques dispersés horizontalement. J’ai proposé une plateforme photonique intégrée composée d’une LED à nanofil, d’un guide d’onde optimisé et d’un photodétecteur à nanofil. J’ai également développé un système d’alignement des nanofils.L’intégration verticale a pour objectif la réalisation de LEDs flexibles reposant sur une assemblée de nanofils verticaux encapsulées dans des polymères. Je montre que ceci permet la fabrication de LEDs flexibles monochromatiques, bi-couleurs ou blanches.Les nanofils épitaxiés sur des matériaux 2D par épitaxie de van de Waals sont faciles à décoller de leur substrat natif. Avec cette motivation, dans la dernière partie de cette thèse, j’ai étudié la croissance organisée des nanofils GaN sur du graphène micro et nano-structuré utilisant l’épitaxie par jets moléculaires<br>Nitride nanowires exhibit outstanding opto-electronic and mechanical properties and are considered as promising materials for light-emitting diodes (LEDs), thanks to their high crystalline quality, non-polar facets, good mechanical flexibility, high aspect ratio, etc.This Ph.D. thesis addresses the growth, the device fabrication, the optical and electrical characterizations and the optical simulations of III-nitride NW devices, with a special emphasis on the LED applications.First, this thesis presents the growth of m-plane InGaN/GaN quantum wells with different In concentrations in self-assembled core-shell nanowires by metal-organic chemical vapor deposition. Then, by using these nanowires, LED devices based on two different integration strategies (namely, in-plane and vertical integration) are demonstrated.The in-plane integration is based on the horizontally dispersed single nanowires. I have proposed a basic integrated photonic platform consisting of a nanowire LED, an optimized waveguide and a nanowire photodetector. I have also developed a nanowire alignment system using dielectrophoresis.The vertical integration targets the fabrication of flexible LEDs based on vertical nanowire arrays embedded in polymer membranes. Flexible monochromatic, bi-color, white LEDs have been demonstrated. Their thermal properties have been analyzed.The nanowires grown on 2D materials by van der Waals epitaxy are easy to be lifted-off from their native substrate, which should facilitate the fabrication of flexible nanowire devices. With this motivation, in the last part of this thesis, I have investigated the selective area growth of GaN NWs on micro- and nano- scale graphene by molecular beam epitaxy

In the last decades, investigations of organic light-emitting diodes (OLEDs) have tackled several key challenges of this lighting technology and have brought the electron to photon conversion efficiency close to unity. However, currently only 20% to 30% of the photons can typically be extracted from OLED structures, as total internal reflection traps the major amount of the generated light inside the devices. This work focuses on the optimization of the optical properties of top-emitting OLEDs, in which the emission is directed away from the substrate. In this case, opaque materials, e.g. a metal foil or a display backplane can be used as substrate as well. Even though top-emitting OLEDs are often preferred for applications such as displays, two main challenges remain: the application of light extraction structures and the deposition of highly transparent materials as top electrode, without harming the organic layers below. Both issues are addressed in this work. First, top-emitting OLEDs are deposited on top of periodically corrugated light outcoupling structures, in order to extract internally trapped light modes by Bragg scattering and to investigate the basic scattering mechanisms in these devices. It is shown for the first time that the electrical performance is maintained in corrugated top-emitting OLEDs deposited on top of light extraction structures. Furthermore, as no adverse effects to the internal quantum efficiency have been observed, the additional emission from previously trapped light modes directly increases the device efficiency. It has been proven that the spectral emission of corrugated OLEDs is determined by the interference of all light modes inside the air light-cone, including the observation of destructive interference and anti-crossing phenomena. The formation of a coherently coupled mode pair of the initial radiative cavity mode and a Bragg scattered mode has been first observed, when grating structures with an aspect ratio > 0.2 are applied. There, the radiative cavity mode partially vanishes. The observation and analysis of such new emission phenomena in corrugated top-emitting OLEDs has been essential in obtaining a detailed insight on fundamental scattering processes as well as for the optimization and control of the spectral emission by light extraction structures. Second, the adverse impact of using only moderately transparent silver electrodes in white top-emitting OLEDs has been compensated improving the metal film morphology, as the organic materials often prevent a replacement by state-of-the-art electrodes, like Indium-tin-oxide (ITO). A high surface energy Au wetting layer, also in combination with MoO3, deposited underneath the Ag leads to smooth, homogeneous, and closed films. This allows to decrease the silver thickness from the state-of-the-art 15 nm to 3 nm, which has the advantage of increasing the transmittance significantly while maintaining a high conductivity. Thereby, a transmittance comparable to the ITO benchmark has been reached in the wavelength regime of the emitters. White top-emitting OLEDs using the wetting layer electrodes outperform state-of-the art top-emitting devices with neat Ag top electrodes, by improving the angular colorstability, the color rendering, and the device efficiency, further reaching sightly improved characteristics compared to references with ITO bottom electrode. The enormous potential of wetting layer metal electrodes in improving the performance of OLEDs has been further validated in inverted top-emitting devices, which are preferred for display applications, as well as transparent OLEDs, in which the brittle ITO electrode is replaced by a wetting layer electrode. Combining both concepts, wetting layer electrodes and light extraction structures, allows for the optimization of the grating-OLED system. The impact of destructive mode interference has been reduced and thus the efficiency increased by a decrease of the top electrode thickness, which would have not been achieved without a wetting layer. The optimization of corrugated white top-emitting OLEDs with a top electrode of only 2 nm gold and 7 nm silver on top of a grating with depth of 150 nm and period of 0.8 µm have yielded a reliable device performance and increased efficiency by a factor of 1.85 compared to a planar reference (5.0% to 9.1% EQE at 1000 cd/m2). This enhancement is comparable to common light extraction structures, such as half-sphere lenses or microlens foils, which are typically restricted to bottom-emitting devices. Overall, the deposition of top-emitting OLEDs on top of light extraction structures finally allow for an efficient extraction of internally trapped light modes from these devices, while maintaining a high device yield. Finally, the investigations have resulted in a significant efficiency improvement of top-emitting OLEDs and the compensation of drawbacks (optimization of the white light emission and the extraction of internal light modes) in comparison to the bottom-emitting devices. The investigated concepts are beneficial for OLEDs in general, since the replacement of the brittle ITO electrodes and the fabrication of roll-to-roll processing compatible light extraction structures are also desirable for bottom-emitting, or transparent OLEDs.

Master of Science<br>Department of Architectural Engineering and Construction Science<br>Fred Hasler<br>This paper discusses the color rendition capabilities of light emitting diodes (LEDs) and their relationship with the current standard for color rendition quality. The current standard for judging light source color rendering properties, known as the color rendering index (CRI), has come under heavy scrutiny in recent years with the introduction of LED in commercial lighting applications. LEDs, depending on construction type, have highly structured spectral distributions which do not scale well under the color rendering index; moreover, CRI for LEDs has become disjointed with the subjective measurement of human color preference. Unfortunately, given the multidimensional nature of color, an all-encompassing scale with a single rated value for color rendition capabilities of a light source has proven difficult to establish. An analysis on the human visual system is first discussed, establishing how the visual system first detects color in the eye and subsequently encodes that color information through a color-opponent process, formulating conscious color appearance. The formation of color appearance leads into a discussion on human color vision and the creation of three dimensional color space, which is subsequently used for the measurement of color fidelity (CRI) of consumer light sources. An overview of how LED lamps create light and color is then discussed, showing that the highly structured spectral distribution of LED lamps is often the cause of discrepancy within the CRI system. Existing alternatives to the CRI system are then compared and contrasted to each other, and the existing CRI system. A final color preference study was conducted where four LED lamps where compared to a reference lamp of equal correlated color temperature. Observers were asked to rate the various test lamps against the reference lamp in terms of vividness, naturalness, overall preference, and individual color preference. It was found that no significant difference was found between the first three dimensions measured but significant trend lines existed for the preference of individual colors when illuminated by either LED lamps or the reference source. Recommendations are then made for how the lighting industry could move forward in terms of color metrics.

Light-emitting dendrimers with iridium(III) complex cores have given rise to some of the simplest and most efficient organic light-emitting diodes. However, whilst monochrome devices can be prepared there is currently no method for the patterning of the dendrimer films to give rise to pixelated colour displays. The main aim of this project was to develop methodology for the patterning of dendrimer films. In particular, dendrimers are designed that have an oxetane surface group that can be crosslinked to form patterns by a photo-generated acid.

This thesis focuses on the development, measurement and application of novel micrometre-sized light emitting diodes (micro-LEDs) based on Gallium Nitride (GaN) for visible light communications (VLC) in both free-space and guided wave configurations. The goal is to set benchmarks for LED-based wireless optical communications. An overview of the field integrating research, industry and standards is presented. A top-down approach is taken with application requirements driving development of new micro-LEDs with simultaneously increased optical power and modulation bandwidth. This was achieved by mitigating two limitations, namely current crowding and mutual device heating. Two novel techniques were developed to access pixel performance: spatially-resolved mapping of modulation bandwidth and spectral characteristics, and thermal imaging. On this basis, broad-area LEDs were used to understand the independent benefits, providing insight for the design of novel micro-LEDs. Circular segmented micro-LEDs emitting at 450nm achieved modulation bandwidths in excess of 800MHz, the highest reported for LEDs, while maintaining optical power above 2mW. In data transmission using systems with 1.8GHz bandwidth,the devices achieved 8Gbps in free-space and guided-wave operation at wavelengths of 400nm, 450nm and 520nm. Ring and half-ring micro-LEDs introduced here have shown modulation bandwidths that scale with the increase of active area and consequently optical power. Bandwidths in excess of of 600MHz were achieved at optical powers over 5mW. In data transmission using a system limited to 1GHz bandwidth, these devices achieved 7Gbps in free-space operation.