Dissertations / Theses on the topic 'Physical suitability'

This study examined the reliability and the validity of the Exercise Suitability Scale (ESS). The ESS was a psychometric instrument developed to measure the suitability of four different forms of exercise (aerobics, bicycling, jogging, and swimming) for different individuals. Aspects of Exercise Suitability included in the ESS were ease, satisfaction, enjoyableness, fatigue, interest, convenience, comfort, safety, affordability, and time-involvement. Background information relating to the development of the ESS as well as methods and results of testing the instrument for reliability and validity were included in this study. Data from a student population were used for estimating the reliability and validity of the ESS. Reliability testing included computing inter-item and item-to-total correlation coefficients, Cronbach's alpha, and internal consistency coefficients (theta and omega) derived from factor analytic techniques. Several types of validity were assessed: content validity, criterion-related validity, and construct validity. Criterion-related validity was estimated by comparing scores on the ESS with information about participation in exercise. Multiple regression was also used to assess criterion-related validity. Principal components analysis was used to examine the construct and content validity of the ESS. Construct validity was also estimated by correlating ESS scale scores with a parallel instrumentation approach, a Q-Sort. Satisfactory reliability indices were obtained for all four ESS exercise scales. Criterion-related validity indices were also adequate. Factor analysis provided some evidence of content validity of the ESS, but provided little support for the construct validity of the ESS. Construct validity was supported, however by the convergence approach.

The aim in this study was to develop a model for the probability of finding active golden eagle nests during their breeding season. It was done by using environmental variables derived from expert models which were tested against empirical data. This resulted in a habitat suitability index (HSI), which in this case is assumed to indicate the probability of active nests of golden eagles. The study was conducted together with the County Administrative Board of Västernorrland with the purpose to improve golden eagle’s ecological status.To develop the model, different combinations of several explanatory variables were tested in a model selection process, where the most optimal and parsimonious model was chosen. The tested variables have earlier been shown to affect golden eagles, as slope, aspect, forest age, foraging habitat, suitable flight routes, human population density, roads, railways, power lines, wind power plants, hiking trails and clear cuts. The variables where applied in in ArcMAP at three different scales: nest scale (25 x 25 meter), proximate scale (a circle with the radius of 500 meter) and home range scale (a circle with the radius of 8253 meter). A preliminary test of the variables showed that all golden eagle nests were found in slopes with at least 5֯ degreesas well as in home ranges with human population density not more than 8 people/km2. Due to that a stratified analysis wasperformed. The variables where analysed by multiple logistic regression in R, where the occurrence of golden eagles’ nestswas compared towards random points in the landscape. All variables were also tested one by one by logistic regression. Afterperforming the multiple logistic regression, it was possible to apply its equation into ArcMap to obtain suitability maps withHSI values over Västernorrland’s county.The comparisons of different models show that it is better to combine different spatial scales in the model than only using one spatial scale. The result indicate that three different models might be the best, which all had different combinations of slope and aspect at nest scale and power lines at the proximate scale. Two of these models also include hiking trails and human population density, both at home range scale, in their equation. Since it was some unclarity about the causality between hiking trails and human population density, the conclusion was not to choose any of these as the final model. The final model was more parsimonious and had an additive effect from slope and southern aspect at the nest scale and an antagonistic effect from power lines at the proximate scale.This study clarifies that golden eagles’ habitat preferences for nesting sites during their breeding period is steep slopes (at minimum 5֯ degrees) in more southern aspects with few power lines in the proximate area surrounding the nest. Their homeranges are also situated in areas with less than 8 people/km2. The study also pinpoints a potential conflict between golden eagleand wind power planning, as golden eagles prefer steep slopes and remote areas, which also are valuable areas for wind powerplants. Golden eagles’ preference of remote areas also indicate that they might be affected by human persecution, why certainconservation effort should be focused into this issue. Out from the final model, you can find cluster in the landscape where youcan focus conservation management and restrict exploitation. Due to low number of wind power plants in the landscape, nothingcould be concluded about their effect on golden eagle in this study. An advice from the golden eagle’s perspective is to use theprecautionary principle and further plan wind power plants in areas which already have high disturbance, as for example closeto power lines or roads. The result also indicates that forest age from SLU Forest Map is not suitable for telling where to findgolden eagle nests. GIS-data over forest age would facilitate conservation management for plenty of species connected to theforest.Although good statistical results for the final model, cautions need to be taken in general, since neither population viability analysis have been included, nor changes over time in the landscape. Another issue is the low sample size, where a larger sample size would make it possible to perform profound calibration and validation of the data. To develop a more robust model, the advice is to include these into the model and use a larger sample size.

Digital media holds a strong presence in society today. Providers of digital media may choose to obtain a content rating for a given media item by submitting that item to a content rating authority. That authority will then issue a content rating that denotes to which age groups that media item is appropriate. Content rating authorities serve publishers in many countries for different forms of media such as television, music, video games, and mobile applications. Content ratings allow consumers to quickly determine whether or not a given media item is suitable to their age or preference. Literature, on the other hand, remains devoid of a comparable content rating authority. If a new, human-driven rating authority for literature were to be implemented, it would be impeded by the fact that literary content is published far more rapidly than are other forms of digital media; humans working for such an authority simply would not be able to issue accurate content ratings for items of literature at their current rate of production. Thus, to provide fast, automated content ratings to items of literature (i.e., books), we propose a computer-driven rating system which predicts a book's content rating within each of seven categories: 1) crude humor/language; 2) drug, alcohol, and tobacco use; 3) kissing; 4) profanity; 5) nudity; 6) sex and intimacy; and 7) violence and horror given the text of that book. Our computer-driven system circumvents the major hindrance to any theoretical human-driven rating system previously mentioned--namely infeasibility in time spent. Our work has demonstrated that mature content of literature can be accurately predicted through the use of natural language processing and machine learning techniques.

Thesis (MScAgric)--Stellenbosch University, 2012<br>ENGLISH ABSTRACT: Biochar has been labelled to be a key factor in the global carbon mitigation act and has been described as the modern day equivalent (terra nova) to the terra preta dark earth soils of the Brazilian Amazon. Globally biochar has been evaluated as a means to improve soil fertility and to mitigate greenhouse gases (GHGs). Little research has however been published on the effects of biochar incorporation on soil physical properties. The objective of this study was to evaluate the effect of pine sawmill waste derived biochar (locally-produced via slow pyrolysis – 450°C) on selected soil physical properties, soil-water dynamics and crop production and- performance, when amended to a Kroonstad (Kd 1000 – Morgendal) soil form. This soil form is commonly found in the Western Cape area (South Africa) and can be classified as having low agricultural suitability for perennial- and annual crop species. Two pot trials were carried out in an atmospheric controlled greenhouse, where winter wheat and green beans respectively were planted, with five different application levels of biochar (0t/ha, 1t/ha, 10t/ha, 50t/ha and 200t/ha). Soil physical properties namely, water-stable aggregates, bulk density and water-retention capacity along with physiochemical characterisation of the sandy soil and biochar was determined. The water-use was monitored throughout the trials (evapotranspiration, volumetric water content and biomass water use efficiency, BWUE). The above- and below ground (specific leaf traits for the green bean and the root structural development for the winter wheat) biomass was collected and analysed at harvest. There was significantly higher volumetric water content measured for the 50t/ha and 200t/ha biochar treatments. This effect can be ascribed due to a change in the soil’s tortuosity and porosity where more meso- and micro-pores were present as the biochar rate increased. The same results were evident when a water-retention curve was established in vitro by means of the sandbox method. The bulk densities were only significantly lower for the 200t/ha biochar treatments. The wheat root systems differed greatly among the fertilised biochar treatments: the 50t/ha and 200t/ha treatments had a more complex fibrous root system (more extensive branching and thinner roots) than 0t/ha, 1t/ha and 10t/ha application levels. This is attributed to the increased water-holding capacity along with a reduction of N- and P availability with increasing addition of biochar. Several leaf traits were measured for the green bean crops; however the leaf nitrogen- and carbon content, chlorophyll content index (CCI) and carbon isotope fractionation yielded the most interesting findings. Concerning the fertilised biochar treatments, there was established that the 10t/ha treatments had the highest leaf nitrogen- and carbon content. The leaf chlorophyll content did not differ significantly between the fertilised biochar treatments; however a very interesting observation was evident regarding the measured leaf CCI for the unfertilised treatments. A decreasing trend and lower leaf CCI was measured as the biochar application levels increased. This effect was ascribed to be due to a decrease in N uptake by the plants as the biochar application increased, the C/N ratio also increased, and this leading to N immobilisation. The lowest leaf carbon isotope fractionation was measured for the 10t/ha fertilised treatments and is inversely correlated with BWUE and therefore endorses the conclusion that the 10t/ha biochar application had a positive effect on the long term water use efficiency for the green bean plants. Biochar promoted aggregation in the sand-rhizosphere interface for winter wheat, increased water-holding capacity and enhanced crop performance for green beans. The findings reported here provide new information on the effect of biochar on the structural development of sandy soil, combined with biochar- and root growth effects for winter wheat; along with detailed interpretations of specific leaf traits associated with crop production for commercial green beans. The addition of biochar at low application levels (approximately 1-10t/ha to 15 cm depth) increased the biomass yield and water use efficiency of the crop species. Besides long term carbon storage, biochar can have immediate positive effects on the physical properties of sand and plant growth.<br>AFRIKAANSE OPSOMMING: Biokoolstof word beskou as ‘n sleutel komponent rakende die wet op globale koolstofvermindering en is al beskryf as die moderne ekwivalent (terra nova) van die terra preta donker-aardgronde wat aangetref word in die Brasiliaanse Amasone. Wêreldwyd word biokoolstof tans geëvalueer met die doel om grondvrugbaarheid te verbeter asook kweekhuisgasse (KHG) se nadelige gevolge te verlig. Min navorsing was tot dus ver gedoen rakende die uitwerking met toediening van biokoolstof op grondfisiese-eienskappe. Die doel van hierdie studie was om die effek van biokoolstof, wat afkomstig is van denne-saagmeul-afval (plaaslik geproduseer is en d.m.v. stadige perolise - 450°C) te evalueer aangaande die volgende faktore: geselekteerde grondfisiese-eienskappe, grond-waterdinamika interaksie en die uitwerking op gewasproduksie; met toediening aan 'n Kroonstad (Kd 1000 - Morgendal) grondvorm. Hierdie grondvorm word as algemeen in die Wes-Kaap (Suid-Afrika) bestempel en kan geklassifiseer word as ‘n lae-geskiktheid landbougrond vir meerjarige- en eenjarige gewasse. Twee potproewe is uitgevoer onder beheerde atmosfeer in ‘n kweekhuis, waar winter koring en groenbone geplant is, met vyf verskillende behandelings van biokoolstof (0t/ha, 1t/ha, 10t/ha, 50t/ha en 200t/ha). Die volgende grondfisiese-eienskappe is ondersoek, naamlik water-stabiele aggregaat formasie, bulkdigtheid en waterhouvermoë, asook die fisiochemiese karakterisering van die sanderige grond en biokoolstof wat gebuik is. Waterverbruik is gedurende die proewe gekontroleer (evapotranspirasie, volumetriese waterinhoud en die biomassa se water verbruiksdoeltreffendheid, BWVD). Die bo- en ondergrondse biomassa, spesifiek die blaareienskappe van die groenboontjie en die strukturele ontwikkeling van die winter koring se wortels, is tydens die oes ondersoek en ontleed. Die volumetriese waterinhoud was betekenisvol, asook hoër vir die 50t/ha en 200t/ha behandelings. Hierdie effek word toegeskryf as gevolg van 'n verandering in die grond se kronkeligheid en porositeit; waar meer meso- en mikroporieë teenwoordig was soos die biokoolstof inhoud toegeneem het. Dieselfde resultate was verkry met die opstelling van ‘n water-retensie kurwe in vitro d.m.v. die Sandboks metode. Bulkdigtheid was slegs betekenisvol verskilled asook aansienlik laer vir die 200t/ha biokoolstof behandelings. Die koring se wortelstelsel het drasties verskil tussen die verskillende bemeste biokoolstof behandelings: die 50t/ha en 200t/ha behandelings het 'n meer komplekse en veselagtige wortelstelsel gevorm (hoër graad van vertakking en dunner wortels was aanwesig) as die 0t/ha, 1t/ha en 10t/ha behandelings. Die effek word toegeskryf aan die toenemende waterhouvermoë, tesame met 'n tekort aan N- en P-beskikbaarheid soos die biokoolstof toedieningshoeveelhede verhoog het. Verskeie blaareienskappe is gemeet vir die groenboon gewasse, maar die blaar stikstof- en koolstof-inhoud, chlorofil inhoud indeks (CII) en koolstof-isotoop fraksionering het die mees interessante bevindinge opgelewer. Die hoogste blaar stikstof-en koolstof-inhoud is gemeet vir die 10t/ha bemeste biokoolstof behandelings. Die blaar chlorofil inhoud het nie beduidend verskil tussen die bemeste biokoolstof behandelings nie, maar daar was egter 'n baie interessante waarneming vir die onbemeste biokoolstof behandelings. ‘n Tendens was aanwesig waar die CII afgeneem het soos die biokoolstof toedieningshoeveelheid ook afgeneem het vir die onbemeste behandelings. Die effek word toegeskryf as gevolg van 'n afname in N-opname deur die plant soos die biokoolstof toedieningshoeveelheid verhoog is en tot gevolg gehad het dat die C/N-verhouding ook toegeneem het, wat gelei het tot N-immobilisasie. Die laagste blaar koolstof-isotoop fraksionering was geassioseer met die 10t/ha bemeste biokoolstof behandelings en is omgekeerd gekorreleerd met BWVD en onderskryf dus die gevolgtrekking dat die 10t/ha biokoolstof behandeling 'n positiewe uitwerking het op die langtermyn waterverbruiksdoeltreffendheid vir groenboontjie plante. Biokoolstof het aggregasie bevorder binne die wortelsone, asook deurgans die waterhouvermoë verhoog en gewasproduksie verbeter. Hierdie bevindinge lewer nuwe inligting oor die effek van biokoolstof op die strukturele ontwikkeling van sanderige grond en die gekombineerde interaksie met biokoolstof toediening en hoe dit wortegroei beïnvloed van winter koring; asook 'n gedetailleerde interpretasie van spesifieke blaareienskappe wat verband hou met die produksie van gewasse vir kommersiële verbouing soos die groenboontjie. Die toediening van biokoolstof by die lae hoeveelhede (ongeveer 1-10t/ha tot op 15 cm diepte) het die opbrengs en waterverbruiksdoeltreffendheid van die gewasse verbeter. Behalwe vir die langtermyn koolstofvaslegging, kan biokoolstof toediening onmiddellike positiewe resultate teweeg bring aangaande die fisiese eienskappe van sandgronde en plantegroei.

In 2000 the European Union introduced the Water Framework Directive, new legislation that regulates the use of surface waters within the European Community. The goal of this legislation is to protect, enhance and restore all surface waters within the Community to Good Surface Water Status. Good-Status is described as having low levels of anthropogenic distortion in its hydro-morphological and physiochemical components as well as possessing biota that would normally be associated with the type-specific aquatic ecosystem. The assessment of ecosystem status is to be defined by comparisons with intact representative reference sites, by using modelling techniques that define reference conditions, a combination of the two, or expert judgement. As undisturbed aquatic ecosystems are rare or non-existent in Europe the base-line data will have to be defined using the latter methodologies. The aim of this project is to help define reference conditions for lotic systems in Europe based on the physical instream habitat parameters of a resident species. Brown trout (Salmo trutta), a ubiquitous and well studies species endemic to Europe, was used as the target organism to develop the assessment protocol. The project focused on the requirements this species has of aspects of its physical habitat; specifically, its usage of depth, velocity, and substrate. An extensive survey of the scientific literature was used to define the requirements trout has for the three physical parameters at four life stages. These are the spawning, nursery, juvenile and adult-resident life stages. These requirements were expressed as tolerance profiles, which defined suitable, usable and not-suitable habitat. The methodology was demonstrated by evaluating the physical habitat available at six reaches in three small streams, March, Burnhouse and Bin Burns, which drain into the Carron Valley Reservoir in central Scotland. From the perspective of water depth, these streams seem best suited as nursery areas, are less well suited as juvenile habitat, and do not appear to be well matched for adult residents. The assessment of both velocity and substrate indicated that the portion of the study reaches available for use by resident brown trout increased with trout size. The assessment of all three physical habitat parameters at all study reaches found variable portions of the streams suitable for use by spawning trout. When the habitat variables are integrated all stream segments streams seem best suited as nursery and spawning areas. To a lesser extent juvenile trout can use these burns and very little habitat is available for use by adult resident trout. The tolerance profiles that were created in this study are standardized assessment criteria that when compared with stream survey data can produce an appraisal of habitat availability in any fluvial freshwater system that supports populations of brown trout (Salmo trutta). The assessment method can be combined to produce an integrated habitat assessment, using both an index and by the calculation of Froude number, which is a more realistic approach than the assessment of individual habitat parameters as salmonids choose their microhabitat based on multiple factors. This approach allows an investigator to determine the amount and relative portion of useable habitat and to determine the quality of that habitat. Finally, by examining the physical habitat variable that most strongly correlates with the final integrated habitat distribution the individual habitat parameter that is most important to the distribution of physical habitat at a site can be determined. While this technique would certainly benefit from further development it does show potential to aid in physical habitat assessment of trout streams.

The International Muon Ionization Cooling Experiment (MICE) is designed to demonstrate the currently untested technique of ionization cooling. Theoretically, this process can condition the high quality muon beams required to build a neutrino factory or muon collider which will be the next generation of machines for the study of Particle Physics. The beam line to transport muons into the MICE cooling channel lattice cell was installed in December 2009. Step I of the experimental programme, whose goal was to demonstrate that the beam line can generate beams similar to those expected in a neutrino factory cooling channel, was completed in August 2010. Methods were developed to use time difference measurements in the MICE time of flight counters (TOFs) to obtain a transverse spatial resolution of approximately 10 mm and to track muons through the focusing elements of the beam line, thus allowing the trace space vectors of individual muons to be reconstructed and their integrated path length to be calculated. The TOFs were used to make an absolute measurement of the momentum of muons with zero bias and a systematic error of less than 3 MeV/c. The measured trace space vectors of single muons were used to estimate the emittances and approximate optical parameters of eighteen muon beams. The results of beam line simulations were compared with the measurements and, once the effects of experimental resolution had had been included, found to be in good agreement. A sample of individual muons whose phase space vectors had been measured was injected into a simulation of the full MICE cooling channel; the beam was found to be suitable for demonstrating muon cooling, although some fine tuning of the cooling channel optics will eventually be required.

This study constructed habitat suitability criteria for fishes of the South Fork of the Shenandoah River, in Virginia. The criteria will be used in an IFIM study to produce estimates of the discharge required by fishes in the South Fork. Chi-square tests were used to evaluate whether criteria described habitat use to a statistically significant degree. Secondly, chi-square tests were used to test transferability. The criteria described the habitat use of seven taxa commonly found in the South Fork to a statistically significant degree. Habitat criteria for two taxa did not describe their habitat use to a statistically significant degree. One set of criteria from the North Fork of the Shenandoah transferred to the fish observed in the South Fork. Secondly, this paper examined observer effects of underwater observation. It was of interest to explore how observer effects influenced habitat suitability criteria.

In this work, the suitability of amorphous semiconductors as hard field optical sensors for application in optical process tomography (OPT) has been established. Two amorphous semiconductors were selected for the study, these being amorphous arsenic triselenide (a-As 2 Se3) and hydrogenated amorphous silicon (a-Si:H). The a-As2Se3 device was a single layered structure of 60|Um thickness fabricated upon a 2mm thick cylindrical aluminium substrate. The a-Si:H device was a multi-layered structure of 27.1fim overall thickness fabricated upon a 4mm thick cylindrical aluminium substrate. 20mm 2 samples were cut from the cylinders, their surface being left free for a xerographic investigation. For a tomographic investigation, semitransparent gold (Au) contacts were sputtered onto the surface of the devices to produce single contacts or contact arrays. The study comprised of the two fields of xerography and tomography. The xerographic study comprised of the measurement of such parameters as charge acceptance, dark decay, residual potential, and photoinduced discharge. The research project has concurred with other workers in that the dark discharge mechanism in a-As 2 Se 3 proceeds via a xerographic depletion discharge process, and a Poole-Frenkel type emission in a-Si:H. The tomographic investigation involved the study of such parameters as detectivity, responsivity, steady state photocurrent, and photoinduced fatigue. Detectivity has found to be dependant upon the magnitude of applied electric field and level of incident irradiance. Irradiance in the order of 3.45mW/cm 2 to 9.57mW/cm 2 for a- fj f\ As 2 Se3 and 5.31mW/cm to 28.32mW/cm for a-Si:H was required in order to produce a clean and repeatable photogenerated current pulse over the range of electric fields specified (0.66xl05 V/cm to 1.66xl05 V/cm). The production of steady state current has found to be dependant upon the magnitude of electric field, the level of irradiance, and the illumination period. Irradiance of 319mW/cm 2 to 1.46W/cm2 with an illumination period of 520ns was required to produce steady state photocurrent in a-As2Se3 , and 693mW/cm2 to 2.62W/cm 2 with an illumination period of 880ns for a-Si:H. A linear relationship between electric field and responsivity has been observed in both materials over a range of irradiance of 3.45mW/cm 2 to 9.57mW/cm2 . Responsivity in the order of 87.86|LiAAV to 145.19|iA/W for a-As2Se 3 and 14.19(iAAV to 103.81)J,AAV for a-Si:H has been demonstrated. An investigation as to the effects of photoinduced fatigue in both a-As 2 Se3 and a-Si:H has been carried out by the application of pulsed visible light of various flash repetition rate (FRR) under a constant high electric field over a 30 minute illumination period. It has been shown that the rate of fatigue is dependant upon the material, time, electric field, light intensity, and FRR. A maximum operating speed of 20Hz has been determined for a-As 2Se 3 and lOOHz for a-Si:H. The maximum operating speed of 20Hz for a-As 2 Se 3 was deemed unsuitable for OPT application and the a-As 2 Se 3 material was eliminated from further tomographic investigation. Tomographic prototypes were employed to establish the a-Si:H devices ability to produce qualitative and quantitative data. The results of this investigation demonstrated that 1mm changes in water level and 0.5% changes in fluid colour could be accurately determined by the a-Si:H device at speeds required for OPT. The use of an a-Si:H device containing a Au contact array facilitated the imaging of the curvature of a pipeline and a phantom object contained within the pipeline. The results of the overall investigation have confirmed that the a-Si:H device is suitable for application as a hard field optical sensor for OPT.

This thesis presents a methodological approach to developing the capability of the Infrared Atmospheric Sounding Interferometer (IASI) instrument to inform on the atmospheric concentrations of carbon monoxide (CO), focussing on three key studies: 1) an assessment of the radiometric accuracy of the instrument; 2) the development of the University of Leicester IASI Retrieval Scheme (ULIRS) to convert measured radiances into a CO product; and 3) an investigation into the reliability and possible use of the ULIRS product. An intercomparison between the radiances as measured by the IASI and Advanced Along Track Scanning Radiometer (AATSR) instruments is performed, and absolute differences at 11 µm of less than 0:1K are observed. Given the radiometric behaviour across the IASI instrument as a whole, it is also concluded that the IASI instrument is radiometrically accurate to < 0.3K in the 12 and 4.7 µm spectral regions. A retrieval scheme, the ULIRS, is developed with explicit digital elevation and emissivity information, and a correction for solar surface reflection with a high resolution solar spectrum. Typical random errors over the African region relating to the profiles are found to be ~10% at 5 and 12 km, and on the total columns to be ~12 %. The ULIRS dataset and the operational CO products from the Measurements Of Pollution In The Troposphere (MOPITT) are inter-compared. A methodology which uses the same a priori statistics, and which reduces the smoothing bias between the two sets of data shows that there is only a small bias between the ULIRS and MOPITT V4 products. A simplified top-down approach to estimating CO emissions from fires is also presented, highlighting the need for a better understanding of the correct detection of burnt area from space-based measurements.

Cyber-Physical Systems theory is a new concept that is about to revolutionize the way computers interact with the physical world by integrating physical knowledge into the computing systems and tailoring such computing systems in a way that is more compatible with the way processes happen in the physical world. In this master’s thesis, Field Programmable Gate Arrays (FPGA) are studied as a potential technological asset that may contribute to the enablement of the Cyber-Physical paradigm. As an example application that may benefit from cyber-physical system support, the Electro-Slag Remelting process - a process for remelting metals into better alloys - has been chosen due to the maturity of its related physical models and controller designs. In particular, the Particle Filter that estimates the state of the process is studied as a candidate for FPGA-based computing enhancements. In comparison with CPUs, through the designs and experiments carried in relationship with this study, the FPGA reveals itself as a serious contender in the arsenal of v computing means for Cyber-Physical Systems, due to its capacity to mimic the ubiquitous parallelism of physical processes.<br>text

碩士<br>義守大學<br>土木與生態工程學系<br>104<br>Due to the effect of climate change and uneven rainfall, main issues of river management focused on the flood control and water resources distribution. There are some weirs or dams built across the river bank without any consideration on the aqua-habitat properties that affected by various factors, such as velocity, depth or river bed materials. Ecological engineering and river ecology conservation became the hot study topics since 2000. In order to meet the requirement of aqua-habitat, “base flow” or “ecological base flow” is proposed as the guidelines during river management or water resources planning. One of the distinguished studies on river habitat conservation or restoration, weighted usable area (WUA) concept, was initiated by USGS. WUA considers the combination of velocity, depth, bed-materials and water temperature to simulate suitable area for the specific aqua-species in stream. Case study used in this paper is the reaches along Qishan River. Section properties (sectional profile, velocity, and discharge) from Bin-chiao to Chia-sian-chiao were collected. The suitable curve of red-trout and rainbow-trout were obtained from previous research report of Qishan River. Physical Habitat Simulation model (PHABSIM) developed by USGS is used in this paper to calculate the WUA under different flow rate and modification of cross section by groundsill works. Discharges from 30cms to 60cms are assumed as flow conditions, and grand sill raised river bed around 50cm~100cm are aligned as the river bed modification case. Results of the simulation show the WUA increased gradually by the increasing river flow. WUA is decreased due to groundsill at low flow, but increased rapidly at high flow. Since groundsill thwarts the river flow at high flow that makes more suitable zone for aqua-habitat. When the river flow depletes, some of habitat are replaced by concrete groundsill, and suitable area decreased.

The "beauty is beastly" effect, in which physically attractive females are held at a disadvantage in selection for male sex-typed jobs, is often cited in the physical attractiveness bias research, but has rarely ever been replicated. This study addresses the issue of stimulus sampling, a key shortcoming in previous attractiveness research. Using a large sample of photographic stimuli, as well as a larger number of jobs than is usually used in such research, this study replicates the effect and demonstrates that it is more reliably driven by the extent to which physical appearance is seen as important for a given job, rather than a job's sex-type.

The loss of a hand or arm is a devastating life event that results in many months of healing and challenging rehabilitation. Technology has allowed the development of an electronic replacement for a lost limb but similar advancements in therapy have not occurred. The situation is made more challenging because people with amputations often do not live near specialized rehabilitation centres. As a result, delays in therapy can worsen common complications like nerve pain and joint stiffness. For children born without a limb, poor compliance with the use of their prosthesis leads to delays in therapy and may affect their development. In many parts of the world, amputation rehabilitation does not exist. Fortunately, we live in an age where advances in technology and engineering can help solve these problems. Virtual reality creates a simulated world or environment through computer animation much like what is seen in modern video games. An experienced team of rehabilitation doctors, therapists, engineers and computer scientists are required to realize a system such as this. A person with an amputation will be taught to control objects in the virtual world by wearing a modified electronic prosthesis. Using computers, it will be possible to analyze his or her movements within the virtual world and improve the wearer's skills. The goals of this system include making the system portable and internet compatible so that people living in remote areas can also receive therapy. The novel approach of using virtual reality to rehabilitate people with upper limb amputations will help them return to normal activities by providing modern and appropriate rehabilitation, reducing medical complications, improving motivation (via gaming modules), advancing health care technology and reducing health care costs. The use of virtual reality technology in the field of amputee rehabilitation is in its earliest stages of development world wide. A virtual environment (VE) will facilitate the early rehabilitation of a patient before they are clinically ready to be fitted with an actual prosthesis. In order to create a successful virtual reality rehabilitation system such as this, an accurate method of tracking the arm in real-time is necessary. A linear displacement sensor and a microelectromechanical system (MEMS) inertial measurement unit (IMU) were used to create a device for capturing the motion of a user's movement with the intent that the data provided by the device be used along with a VE as a virtual rehabilitation tool for new upper extremity amputation patients. This thesis focuses on the design and testing of this motion capture device in order to determine the suitability of current commercially available sensing components as used in this system. Success will be defined by the delivery of accurate position and orientation data from the device so that that data can be used in a virtual environment. Test results show that with current MEMS sensors, the error introduced by double integrating acceleration data is too significant to make an IMU an acceptable choice for position tracking. However, the device designed here has proven to be an excellent cable emulator, and would be well suited if used as an orientation tracker.

Η συγκεκριμένη διπλωματική εργασία, έγινε με σκοπό την λεπτομερή περιγραφή των τεχνικό-γεωλογικών χαρακτηριστικών που δύναται να ταξινομήσουν τα βραχώδη υλικά, ύστερα από εργαστηριακές δοκιμές και μετρήσεις, ως κατάλληλα ή μη κατάλληλα για την χρησιμοποίησή τους ως αδρανή υλικά. Στην εργασία, γίνεται εκτενής αναφορά στις φυσικές-μηχανικές–χημικές–γεωμετρικές και άλλες ιδιότητες που παρουσιάζουν τα υλικά που μπορούν να χρησιμοποιηθούν ως αδρανή, καθώς επίσης δίνεται και λεπτομερής περιγραφή των εργαστηριακών δοκιμών που διεξάχθηκαν, όπως προβλέπονται από τους Ευρωπαϊκούς Κανονισμούς (ΕΝ) περί καταλληλότητας των αδρανών υλικών που βρίσκονται σε συνάφεια με τις νομοθεσίες του Ελληνικού Κράτους. Η εν λόγω εργασία αναφέρεται στις χρήσεις αδρανών υλικών ως έρμα σιδηροδρομικών γραμμών και οδοποιίας. Εργαστηριακά, η παρακάτω διπλωματική εργασία βασίζεται στην λήψη δείγματος από βραχώδες διαβασικό και ηφαιστειακό υλικό το οποίο εξετάστηκε βάσει των πιο πάνω Ευρωπαϊκών Κανονισμών και στην συνέχεια συγκρίθηκε με τα προβλεπόμενα όρια της κάθε εργαστηριακής δοκιμής που αναφέρονται ως εργαστηριακά όρια χρήσης αδρανών υλικών σε έρμα σιδηροδρομικών γραμμών αλλά και οδοποιίας. Μια επιπλέον πτυχή του θέματος που εξετάζουμε είναι οι λατομικές ζώνες(λατομεία), οι οποίες ορίζονται ως ο χώρος που γίνεται μαζική λήψη υλικού, απευθείας από το υγιές τμήμα της βραχομάζας ,που προορίζεται για χρήση αδρανών υλικών και εξετάζονται οι περιορισμοί που προκύπτουν βάσει της Ελληνικής νομοθεσίας στο εν λόγω ζήτημα και αφορούν άμεσα αστικές και κατοικημένες περιοχές. Όλες οι εργαστηριακές δοκιμές που εκπονήθηκαν για το σκοπό αυτό, έλαβαν χώρα στο εργαστήριο Τεχνικής Γεωλογίας του τμήματος Γεωλογίας του Πανεπιστημίου Πατρών. Γίνεται επίσης σύγκριση των εργαστηριακών αποτελεσμάτων με τα αντίστοιχα κατάλληλα όρια. Τέλος, γίνεται γεωμορφολογική και γεωλογική αναφορά της περιοχής του Νομού Κιλκίς, Φλώρινας και Μεθάνων, από όπου πάρθηκαν τα δείγματα και δίνεται μια σύντομη αλλά κατατοπιστική αναφορά στην γεωτεκτονική ζώνη στην οποία ανήκει.<br>This thesis was aimed at a detailed description of the technical - geological characteristics may classify rocky materials, following laboratory tests and measurements, as suitable or unsuitable for use as aggregates. This paper is a detailed report on the physical - chemical - mechanical - geometric and other properties which are the materials that can be used as aggregates, as well as given and detailed description of the laboratory tests performed as specified by European regulations ( EN ) on suitability of aggregates that are consistent with the laws of the Greek state. This work relates to uses of aggregates as railway ballast and road construction. Laboratory, the following thesis is based on sampling from crossing rocky and volcanic material which was examined under the above European Regulations and then compared with existing limits of each laboratory test referred to as laboratory usage limits aggregates in railway ballast but and odopoiias.Mia additional aspect of the matter is the quarrying areas (quarries), defined as the space is massive samples taken directly from the healthy part of the rock mass, which is intended for use aggregates and examines the constraints arising under Greek law on this issue and directly related urban and residential areas. All laboratory tests carried out for this purpose took place in the laboratory of Engineering Geology, Geology Department, University of Patras. It will also compare the laboratory results with the corresponding appropriate limits. Finally Made geomorphological and geological report of the Prefecture of Kilkis, Florina and methane emissions, from which samples were taken and given a brief but informative reference to tectonic zone to which it belongs.

This work inkluse measurement principles for measuring liquid level in tanks with a focus on fuel. Are described most frequently used types of liquid level sensors, focusing on fuel. The work inkluse design chosen technical solutions fuel level sensor and its technical implementation, including the technical implementation and verification of its functionality and calibration.