Dissertations / Theses on the topic 'Telephone switching systems, Electronic'

In this thesis, we study the performance of an antenna switching (AS) system in comparison to an Alamouti coded system. We analyze the outage probabilities and propose minimum mean-squared error based iterative equalizers for both systems. We see from the outage probability analysis of both systems that the AS system may achieve the same diversity order of the Alamouti coded scheme contingent on the transmission rate and constellation size. In the proposed receiver, MMSE equalization and channel decoding are jointly carried out in an iterative fashion. We use both hard and soft decision channel decoders in our simulations. It is observed that the Alamouti based scheme performs better when the channel state information is perfect. The Alamouti scheme also performs better than the AS scheme when the channel state information is imperfect in hard decision channel decoder case and a random interleaver is used. On the other hand, if a random interleaver is not used, AS scheme performs remarkably better than the Alamouti scheme in hard decision channel decoder case. In a soft decision channel decoder case, when the channel state information is imperfect, the AS scheme performs approximately a 2 dB better than the Alamouti scheme. Moreover, there is approximately a 3 dB performance gain if a soft decision channel decoder is used instead of hard decision.

Thesis (MScIng)--University of Stellenbosch, 2008.
ENGLISH ABSTRACT: The Applications of Superconductors in Cellular Network Base Stations R. Du Toit Department of Electronic Engineering University of Stellenbosch Private Bag X1, 7602 Matieland, South Africa Thesis: MScEng (E&E) March 2008 Wireless communications have increasingly become part of our world. The growth of radio frequency (RF) wireless communications has led to an increasing demand for frequency spectrum licenses, increased system capacity and larger user bandwidths. These demands lead to frequent improvements on the physical and higher layers of wireless communication protocols. Changes in the physical layer are frequently followed by the need for replacement of dedicated hardware components. The need therefore exists for a more general and programmable physical layer. A more general and programmable radio architecture implies increased radio front-end performance without losing programmability. The contribution of this thesis is the analysis of how superconductor electronics (SCE) using Rapid Single Flux Quantum (RSFQ) logic may advance wireless radio front-ends by providing a general-purpose programmable radio architecture. Superconductor analogue to digital converters (ADCs) are employed as high performance, programmable digitization structures. Once a received signal is digitized, SCE can be used to rapidly do recursive operations such as synchronization and multi-path delay estimation. These operations are based on correlation, and for evaluation of such operations with SCE the popular CDMA multiplexing method is studied along with the WCDMA protocol used in the 3G UMTS standard. Two delta-type oversampling superconductor ADC modulator designs are presented and evaluated along with a hybrid decimation filter design, using both the benefits of SCE and room temperature electronics. A fast RSFQ correlator design is also presented and evaluated for use in a multi-path estimation structure. A rapid multi-path delay estimation architecture based on fast RSFQ circular data buffers and correlators is presented. The architecture uses the fast speeds of RSFQ logic to obtain accurate path delay estimates in a rapidly changing wireless environment. It is concluded that RSFQ-based wireless receiver components offer promising new options for data conversion, correlation and multi-path delay estimation implementations.
AFRIKAANSE OPSOMMING: The Applications of Superconductors in Cellular Network Base Stations R. Du Toit Department of Electronic Engineering University of Stellenbosch Private Bag X1, 7602 Matieland, South Africa Thesis: MScEng (E&E) March 2008 Draadlose kommunikasie word al hoe meer deel van ons wêreld. Groei in radiofrekwensietipe kommunikasie het gelei tot ’n toenemende aanvraag na frekwensiespektrum lisensies, vergrote stelselkapasiteit en groter gebruikerbandwydtes. Hierdie aanvrae lei tot gereelde en spoedige verbeteringe op die fisiese en hoër lae van huidige draadlose kommunikasieprotokol. Veranderinge in die fisiese laag vereis gewoonlik dat toegewyde hardewarde komponente vervang word. Die behoefte bestaan dus vir ’n meer algemene, programmeerbare fisiese laag. Dit vereis dus ’n verbetering in die radio-ontvanger se komponente naaste aan die antenna sonder om programmeerbaarheid te verloor. Die bydrae van hierdie tesis is hoofsaaklik die analise van hoe supergeleierelektronika wat van Rapid Single Flux Quantum (RSFQ) logika gebruik maak, huidige draadlose sellulêre basisstasies se fisiese laag kan verbeter deur ’n meer algemene en programmeerbare radio-argitektuur op te lewer. Supergeleier analoog-na-syfer omsetters (ADCs) word bestudeer as moontlike programmeerbare versyferingstrukture wat steeds hoë werkverrigting lewer. Wanneer ’n ontvangde sein in digitale vorm omgesit is, kan supergeleierelektronika gebruik word om vinnig rekursiewe operasies uit te voer. Voorbeelde van sulke operasies is sinkronisasie en die waardebepaling van die vertraging van verskillende paaie wat ’n sein volg na die ontvanger. Hierdie spesifieke operasies se werking is gebaseer op korrelasie, en vir die evaluasie van sulke operasies met supergeleierelektronika is die gewilde wyeband-CDMA (WCDMA) protokol wat gebruik word in die 3G UMTS-standaard. Twee supergeleier-delta-tipe oorversyferings-ADC-moduleerderontwerpe word voorgelê en evaluasie word daarop gedoen saam met ’n hibriede desimasiefilterontwerp wat gebruik maak van beide die voordele van supergeleierelektronika en kamertemperatuurelektronika. ’n Vinnige RSFQ-korreleerder word ook voorgelê en evaluasie word daarop gedoen vir gebruik binne ’n multi-padvertraging-waardebepalerstruktuur. Hierdie struktuur wat gebaseer is op RSFQ sirkulêre buffers en korreleerders, word voorgelê. Die waardebepaler maak gebruik van die spoed van RSFQ-logika om akkurate multi-padvertragingswaardes te bepaal in ’n vinnig veranderende draadlose omgewing. Die gevolgtrekking word gemaak dat RSFQ-gebaseerde draadlose ontvangerkomponente groot voordele in versyfering-, korreleerder- en multi-padvertragingsbepaler-toepassings bied.

In this study, possible applications of label switching in large area, fully optical networks are investigated. The objective was to design a label assignment method by using Generalized Multi-Protocol Label Switching (GMPLS) concept to get an efficient optical network operation. In order to fulfill this objective, two new approaches were proposed: a label assignment method and a concatenated label structure. Label assignment method was designed to provide an efficient utilization of resources. Concatenated label structure aimed handling the label in optical domain. Mainly, the lambda switch capable GMPLS networks were investigated. In order to verify the performance of label assignment method, a simulator was developed. The results of simulation have clearly indicated that the proposed approaches could be beneficial in an optical network operation.

Thesis (MScEng (Electrical and Electronic Engineering))--University of Stellenbosch, 2005.
Automatic speech recognition (ASR) systems are an attractive means for companies to deliver value added services with which to improve customer satisfaction. Such ASR systems require a telephony interface to connect the speech recognition application to the telephone system. Commercially available telephony interfaces are usually operating system specific, and therefore hardware device driver issues complicate the development of software applications for different platforms that require telephony access. The drivers and application programming interface (API) for telephony interfaces are often available only for the Microsoft Windows operating systems. This poses a problem, as many of the software tools used for speech recognition research and development operate only on Linux-based computers. These interfaces are also typically in PCI/ISA card format, which hinders physical portability of the device to another computer. A simple, cheaper and easier to use USB telephony interface device, offering cross-platform portability, was developed and presented, together with the necessary API.

Thesis (MScEng (Electrical and Electronic Engineering))--University of Stellenbosch, 2007.
The work presented in this Thesis relates to the increased capabilities of the mobile Internet and the possible use of cellphones as an enhancement to video surveillance systems. The focus of the Thesis is on the delivery of live video content to Java enabled cellphones. The various characteristics, capabilities and limitations of the mobile networks- and phones are investigated. Various options for streaming video content to cellphones are also explored. The design and implementation of a digital surveillance system with the ability to stream live video to a cellphone is presented. Two versions of the streaming protocol are developed and implemented in cellphone applications, with which the video stream can be viewed. An evaluation and real-life testing of the applications are presented. Recommendations regarding further enhancements are provided.

Traditionally, real-time communication, such as voice calls, has run on separate, closed networks. Of all the limitations that these networks had, the ability of malicious attacks to cripple communication was not a crucial one. This situation has changed radically now that real-time communication and data have merged to share the same network. The objective of this project is to investigate the securing of softswitches with functionality similar to Private Branch Exchanges (PBX) from malicious attacks. The focus of the project will be a practical investigation of how to secure ILANGA, an ASTERISK-based system under development at Rhodes University. The practical investigation that focuses on ILANGA is based on performing six varied experiments on the different components of ILANGA. Before the six experiments are performed, basic preliminary security measures and the restrictions placed on the access to the database are discussed. The outcomes of these experiments are discussed and the precise reasons why these attacks were either successful or unsuccessful are given. Suggestions of a theoretical nature on how to defend against the successful attacks are also presented.

Orientador: Celso de Almeida
Tese (doutorado) - Umiversidade Estadual de Campinas, Faculdade de Engenharia Elétrica e de Computação
Made available in DSpace on 2018-08-17T06:29:22Z (GMT). No. of bitstreams: 1 Hoefel_RogerPierreFabris_D.pdf: 16131215 bytes, checksum: 8d67fff6992c05fd8d2eac683e4a1f9e (MD5) Previous issue date: 2000
Resumo: O objetivo deste trabalho é o de analisar, caracterizar e apresentar soluções para o excitante desafio de projetar protocolos de acesso para o transporte de pacotes multimídia no enlace reverso de sistemas celulares terrestres que empregam interface do ar do tipo TD/DS-CDMA (Time Division/Direct Sequence Code Division Multiple Access). Os estudos relativos aos aspectos inerentes à transmissão de pacotes em sistemas TD/DS-CDMA são particularizados na análise dos protocolos CDMA/PRMA (Code Division Multiple Access/ Packet Reservation Multiple Access) e Slotted CDMA/ALOHA. CDMA/PRMA é um protocolo de múltiplo acesso híbrido, no qual se aplicam os conceitos de multiplexação no tempo~por código e de alocação de recursos por meio de reserva. O acesso controlado ao canal do protocolo CDMA/PRMA permite a redução da variação da carga instantânea do canal e, conseqüentemente, redução da interferência de múltiplo acesso em relação ao protocolo Slotted CDMA/ ALOHA, onde os terminais acessam no próximo slot de tempo tão logo tenham pacotes a transmitir. Utiliza-se simulação computacional de maneira intensiva para à obtenção de resultados concernentes ao desempenho dos protocolos CDMA/PRMA e Slotted CDMA/ ALOHA em distintas condições operacionais. Estes resultados são validados por análises numéricas. Entre outros aspectos deste trabalho, destaca-se: (i) o modelo do ponto de equilíbrio proposto para os protocolos CDMA/PRMA e Slotted CDMA/ ALOHA; (ii) as expressões numéricas propostas para uma análise de desempenho do protocolo CDMA/PRMA; (iii) o desenvolvimento de um simulador de rede de pacotes para a investigação dos efeitos da interferência externa nas redes de pacotes CDMA/PRMA e Slotted CDMA/ ALOHA; (iv) efeitos dos parâmetros de projeto no desempenho dos protocolos CDMA/PRMA e Slotted CDMA/ ALORA; (v) estudo do desempenho dos protocolos CDMA/PRMA e Slotted CDMA/ ALORA com tráfego de vídeo com taxa variável e tráfego de dados WWW; (vi) a investigação dos efeitos do controle de potência, do desvanecimento rápido e do desvanecimento lento no desempenho dos protocolos CDMA/PRMA e Slotted CDMA/ ALORA com tráfego multimídia; (vii) o projeto integrado do protocolo CDMA/PRMA com receptor de detecção conjunta descorrelacionadora
Abstract: This thesis has the objective of to analyze, to characterize and to propose solutions to the challenge of design medium access control protocols for transmission of multimedia packets over the reverse channel of land mobile cellular systems based on TD/DS-CDMA (Time Division/Direct Sequence Code Division Multiple Access) air interface. Some inherent aspects of packet transmission over the reverse link of TD/DS-CDMA systems are particularized in the analysis of the CDMA/PRMA (Code Division Multiple Access/Packet Reservation Multiple Access) and Slotted CDMA/ ALOHA protocols. The joint CDMA/PRMA protocol is a hybrid multiple-access technique that combines time-division, code-division and Reservation ALOHA concepts. The CDMA/PRMA medium access control brings to reduction of the users variance on the channel, so a larger capacity is obtained in relation to the Slotted CDMA/ ALOHA protocol, where a mobile station accesses a time slot as soon as it has packets to transmit. It is used intensely computational simulation techniques to obtain some performance results concerning to CDMA/PRMA Slotted and CDMA/ ALOHA behavior over distinct operational conditions. It is utilized numerical techniques to validate some of obtained results. It is emphasized the following aspects of this Thesis: (i) a equilibrium point analysis model for the CDMA/PRMA and Slotted CDMA/ ALOHA protocols; (ii) some numerical expressions that permits to analyze the CDMA/PRMA behavior on voice-only traffic; (iii) a system level network simulator developed to assess and to compare the intercell interference effects on the CDMA/PRMA and Slotted CDMA/ ALOHA protocols performance; (iv) the design parameters effects on the performance of CDMA/PRMA and Slotted CDMA/ALOHA systems; (v) some studies of CDMA/PRMA and Slotted CDMA/ALOHA behavior on mixed voice/variable bit rate video and voice/WWW browsing traffic; (vi) some analysis of the imperfect power control effects, slow and fast fading effects on the capacity of CDMA/PRMA and Slotted CDMA/ ALOHA protocols; (vii) a integrated design of CDMA/PRMA protocol and a multiuser decorrelator detector
Doutorado
Telecomunicações e Telemática
Doutor em Engenharia Elétrica

Cette thèse s'intéresse aux problèmes d'allocations des ressources et de puissance dans les réseaux cellulaires de quatrième génération (4G). Pour faire face à la demande continuellement croissante en débit des utilisateurs mobiles, les opérateurs n'ont d'autre choix que de densifier leurs infrastructures d'accès au réseau radio (RAN), afin de maximiser l'utilisation de la bande passante disponible dans l'espace. Un des défis de cette nouvelle architecture est la coexistence de nombreuses cellules voisines et la gestion des interférences co-canal qu'elles génèrent entre elles. De telles contraintes ont amené la communauté scientifique à s'intéresser aux réseaux auto-organisés et auto-optimisés (SON), qui permettent aux réseaux de s'optimiser localement via des décisions décentralisées (sans planification statique). L'intérêt principal de tels réseaux est le passage à l'échelle des algorithmes distribués et la possibilité de s'adapter dynamiquement à de nouveaux environnements. Dans cette optique, nous proposons l'étude de deux problèmes d'allocation de ressources. La première partie de cette thèse se concentre sur l'optimisation de l'usage des ressources, dans un contexte de transmission coordonnée par plusieurs stations de base (CoMP). Les performances de la coordination de stations de base sont évaluées, selon le critère de capacité uniforme, ainsi que le compromis entre l'efficacité spectrale et l'équité entre les utilisateurs. Nous proposons également une méthode généralisée et distribuée de sélection de l'ensemble de stations en coopération, afin d'optimiser le compromis efficacité-équité. Dans une seconde partie, nous nous intéressons à l'optimisation de l'allocation des ressources et de puissance, dans le but de minimiser la consommation électrique du réseau. Nous présentons deux algorithmes dont les décisions sont décentralisées. Le premier est basé sur une optimisation stochastique (via l'échantillonneur de Gibbs) et permet une optimisation globale du système. Le second quant à lui est basé sur l'adaptation de la théorie du contrôle et utilise des modèles prédictifs et la poursuite de cibles pour allouer les ressources et les puissances dans un contexte de canaux et d'interférences dynamiques. Dans de nombreux cas, plusieurs objectifs concurrents sont à considérer pour évaluer les performances d'un réseau (capacité totale, équité, consommation électrique, etc.). Dans le cadre de cette thèse, nous nous efforçons à présenter les résultats sous la forme de compromis multi-objectifs.

The development of pulse code modulation systems and electronic exchanges, together with the increase in volume of data traffic, have made it desirable to establish a means for handling both voice and data trarfic in the telephone network. A technique is required whereby integrated voice and data switching may be accomplished in an electronic exchange. It is proposed that a data adaptor unit be incorporated in electronic exchanges for the ourpose of concentrating data traffic onto PCM highways. A conceptual design for the architecture of such a unit is presented and its performance evaluated. The protocols for connecting data adaptors into a network, and the use of flow control procedures for regulating data traffic within the network, are described. The hardware implementation of the unit is not considered. The proposed data adaptor operates on the packet switching principle. It is comprised of three types of modules each dedicated to carrying out a particular communication function. The modules are the interface processor that interacts with data transmitting devices, the network processor for sending data over PCM channels between adaptors, and the supervisory processor for regulating activities within the adaptor unit.

The growth of mobile networks and the imminent deployment of third generation networks and services will require signalling networks to maintain their integrity during increased unanticipated traffic volumes. As signalling networks become larger and more complex, an analysis ofprotocol operation is necessary to determine the effectiveness of the current protocol implementation and to evaluate the applicability of the proposed enhancements. The objective of this study ,is to develop analytical models to analyse the impact of Signalling Transfer Point congestion on network performance when simple message discard schemes are used as the primary flow control mechanism, and to investigate suitable congestion and flow control mechanisms to help alleviate the congestion. Unlike previous studies, that are localised and only concentrate on the nodes around the congested entity, the models presented here examine the impact of network wide and focused overloads on the entire network. The study considers both the fixed-line and mobile network environments, and analyses the performance of the ISDN User Part and Mobile Application Part protocols. The call completion rate and location update success rate are used to measure performance, instead of message throughput, since these parameters provide a more appropriate measure of the grade-of-service and more accurately reflect the level of service provided to a customer. The steady state equilibrium models, derived here, can be used to quickly estimate the safe operating regions of a signalling network, while the transient models provide a more intuitive perspective of the traffic processes that lead to congestion . Furthermore, these models can be used to examine the network performance for different message priority schemes, routing algorithms, overload scenarios and network configurations. The performance of various congestion control mechanisms that incorporate non-linear throttling schemes is also evaluated, together with an examination of the impact of congestion on multiple user parts in a mobile network environment. Message priority schemes are found to offer little or no advantage in a fixed network environment, but in a mobile network they can be used to maintain the network's performance at an optimum level during periods of overload. Network performance is also improved if congestion controls block load-generating traffic at the initial onset of congestion and then gradually restore traffic as the performance improves .
Thesis (Ph.D.)-University of Natal, Durban, 2002.

This project was undertaken for a commercial electronics company, CONTROL LOGIC (CONLOG) which is involved in the research, design, development and manufacture of data acquisition, control, energy management and automotive equipment. Currently CONLOG uses an inhouse token passing local area network CONET for industrial data communications.The need had arisen to provide a means of data communication amongst widely geographically distributed remote terminal units (RTUs) generating demands at a very low duty cycle. A need for communications between RTUs and a centralised controller was also required. In addition to this, multihop communications between the RTUs was required. Packet switching using a broadcast radio network provides an efficient means of achieving this. An investigation into to the various media access control protocols and contention techniques using packet radio was carried out. The various media access techniques were compared with respect to throughput and normalised delay. This led to the selection of a media access scheme for the packet radio network using RTUs. A protocol specification control is centralised or Interconnect Organisation.The switching protocol (OSI) for the packet radio network, in which distributed, was done. The architechure of specified adheres to the Open Systems model of the International Standards.An experimental packet switching radio network was implemented using the protocol specification defined above. The packet radio network (PACNET) uses existing off the shelf radios and purpose built hardware for the remote terminal units. The thesis describes methods of data communications suitable for widely dispersed industrial data communications, the selection of the packet switching media access methods and control protocols, and the design and implementation of the prototype system.
Thesis (M.Sc.Eng.)-University of Natal, 1992.

Please read the abstract in the section 00front of this document
Dissertation (M Eng (Electronic Engineering))--University of Pretoria, 2006.
Electrical, Electronic and Computer Engineering
unrestricted

Presently, internal combustion engines provide power to move the majority of vehicles on the roadway. While battery-powered electric vehicles provide an alternative, their widespread acceptance is hindered by range anxiety and longer charging/refueling times. Dynamic wireless power transfer (DWPT) has been proposed as a means to reduce both range anxiety and charging/refueling times. In DWPT, power is provided to a vehicle in motion using electromagnetic fields transmitted by a transmitter embedded within the roadway to a receiver at the underside of the vehicle. For commercial vehicles, DWPT often requires transferring hundreds of kW through a relatively large airgap (> 20 cm). This requires a high-power DC-AC converter at the transmitting end and a DC-AC converter within the vehicle.

In this research, a focus is on the development of models that can be used to support the design of DWPT systems. These include finite element-based models of the transmitter/receiver that are used to predict power transfer, coil loss, and core loss in DWPT systems. The transmitter/receiver models are coupled to behavioral models of power electronic converters to predict converter efficiency, mass, and volume based upon switching frequency, transmitter/receiver currents, and source voltage. To date, these models have been used to explore alternative designs for a DWPT intended to power Class 8-9 vehicles on IN interstates. Specifically, the models have been embedded within a genetic algorithm-based multi-objective optimization in which the objectives include minimizing system mass and minimizing loss. Several designs from the optimization are evaluated to consider practicality of the proposed designs.

Adaptive antenna arrays have recently been introduced to cope with the high capacity required by the 3rd generation (3G) wireless communications systems. As adaptive antenna arrays focus narrow high gain beams towards the desired user and nulls towards interferers, both coverage and capacity of the network can be improved. To establish the performance gain that a smart antenna can deliver in a 3G environment (i.e., with mixed traffic), the implementation of adaptive antenna arrays for the uplink of a Wideband Code Division Multiple Access (WCDMA) system in the Frequency Division Duplex (FDD) mode is addressed in this thesis. The beam-forming is implemented with a LS - DRMTA algorithm and a Lagrange multiplier based algorithm using the Q channel only. The results show that the adaptive antenna arrays offer significant performance enhancement over switched beam and single antennas in a 3G environment (i.e., with mixed traffic).

The emergence of portable terminals in work and living environments is accelerating the progression of wireless networks. A wireless ad hoc network is a new network concept where users establish peer-to-peer communication among themselves independently, in their small area. Since the wireless medium is a shared resource, it becomes an important design issue to efficiently allocate bandwidth among users. MAC (Medium Access Control) layer arbitrates the channel access to the wireless medium and is also responsible for bandwidth allocation to different users, therefore a large amount of research has been conducted on various MAC protocols for ad hoc wireless networks. This dissertation begins with a survey of existing wireless MAC protocols. The survey includes protocols designed for different network generations and topologies, classifying them based on architecture and mode of operation. Next, we concentrate on the MAC protocols proposed for distributed wireless networks. We propose a new MAC protocol based on a token-passing strategy; which not only incorporates the advantages of the guaranteed access scheme into the distributed type of wireless networks, but also the data rate and delay level QoS guarantees. Data rate QoS provides fairness into sharing of the channel, while delay level QoS introduces a flexible prioritized access to channels by adjusting transmission permission to the current network traffic activities. A simulation model for the protocol is developed and delay and throughput performance results are presented. To examine the efficiency and performance of the proposed MAC scheme in an ad hoc wireless environment, it is incorporated into the Bluetooth structured network. The model is then simulated in the Bluetooth environment and performance results are presented. Furthermore, an analytical model is proposed and an approximate delay analysis conducted for the proposed MAC scheme. Analytical results are derived and compared with results obtained from computer simulations. The dissertation concludes with suggestions for improvements and future work.
Thesis (M.Sc.-Engineering)-University of Natal, 2003.

Research in the field of random access protocols for narrow-band systems started as early as the 1970s with the introduction of the ALOHA protocol. From the research done in slotted narrow-band systems, it is well known that contention results in all the packets involved in the contention being unsuccessful. However, it has been shown that in the presence of unequal power levels, ore of the contending packets may be successful. Ibis is a phenomenon called capture. Packet capture has been shown to improve the performance of slotted narrow-band systems. Recently, much work has been done in the analysis of spread-spectrum ALOHA type code-division multiple access (CDMA) protocols. The issue of designing power control techniques to improve the performance of CDMA systems by reducing multiple access interference (MAl) has been a subject of much research. It has been shown that in the presence of power control schemes, the performance of spread-ALOHA CDMA systems is improved. However, it is also widely documented that the design of power control schemes capable of the ideal of compensation of radio propagation techniques is not possible for various reasons, and hence the imperfections in power control. None of the research known to the author has looked at capture in spread-ALOHA systems, and to a greater extent, looked at expressions for the performance of spreadALOHA systems in the presence of capture. In this thesis we introduce spread-ALOHA systems with capture as a manifestation of the imperfections in power control. We propose novel expressions for the computation of the perfonnance ofspread-ALOHA systems with capture.
Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, 2005.

Over the last decade, the growth of second generation (2G) digital communications has been explosive. Now wireless communications is evolving to third generation (3G),where it will offer wideband data services and multimedia wideband products and services such as video conferencing and high speed Internet over a mobile phone. Amid these high-tech feature packed mobile devices, there is a major bottleneck of cost. The major cost factor in mobile devices is battery life.

Indiana University-Purdue University Indianapolis (IUPUI)
This research proposes state-of-the-art multilevel converter topologies and their modulation strategies, the implementation of a conventional flying-capacitor converter topology up to four-level, and a new four-level flying-capacitor H-Bridge converter confi guration. The three phase version of this proposed four-level flying-capacitor H-Bridge converter is given as well in this study. The highlighted advantages of the proposed converter are as following: (1) the same blocking voltage for all switches employed in the con figuration, (2) no capacitor midpoint connection is needed, (3) reduced number of passive elements as compared to the conventional solution, (4) reduced total dc source value by comparison with the conventional topology. The proposed four-level capacitor-clamped H-Bridge converter can be utilized as a multilevel inverter application in an electri fied railway system, or in hybrid electric vehicles. In addition to the implementation of the proposed topology in this research, its experimental setup has been designed to validate the simulation results of the given converter topologies.