To see the other types of publications on this topic, follow the link: Welded Zone.

Journal articles on the topic 'Welded Zone'

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles

Select a source type:

Consult the top 50 journal articles for your research on the topic 'Welded Zone.'

Next to every source in the list of references, there is an 'Add to bibliography' button. Press on it, and we will generate automatically the bibliographic reference to the chosen work in the citation style you need: APA, MLA, Harvard, Chicago, Vancouver, etc.

You can also download the full text of the academic publication as pdf and read online its abstract whenever available in the metadata.

Browse journal articles on a wide variety of disciplines and organise your bibliography correctly.

1

Koley, Ishita, and Sukumar Kundu. "Electrochemical behavior of friction stir welded joint of ultra-low carbon steel." IOP Conference Series: Materials Science and Engineering 1248, no. 1 (2022): 012040. http://dx.doi.org/10.1088/1757-899x/1248/1/012040.

Full text
Abstract:
Abstract In this study, friction stir welding of ultra low carbon steel was performed at tool rotational speeds in the range from 300 to 750rpm with 150rpm increments at 60mm/min fixed traverse speed. Throughout study was performed on macro and micro structures in order to determine the several welded zones for example stir zone, thermo-mechanically affected zone, and heat-affected zone. Microhardness profiles were performed along the welded joint's cross section and the utmost hardness was obtained at stir or nugget zone as compared to the other zones of the welded joints. The hardness values
APA, Harvard, Vancouver, ISO, and other styles
2

Yoon, K. H., S. I. Kwun, and Yun Mo Yeon. "Comparison of Fatigue Behavior of FS (Friction Stir) and TIG Welded Al 6N01 Alloy." Key Engineering Materials 417-418 (October 2009): 593–96. http://dx.doi.org/10.4028/www.scientific.net/kem.417-418.593.

Full text
Abstract:
The fatigue properties of friction stir (FS) and TIG welded Al 6N01-T5 alloys were compared in the present study. The low cycle fatigue (LCF) test was performed under total strain amplitudes in the range of ± 0.6 ~ ± 1.5% and with a strain rate of 3 x 10-3/s. During low cycle fatigue, the base metal showed little cyclic hardening or softening, whereas both the FS and TIG welded zones showed a large amount of cyclic hardening until fracture, although the fatigue life of the TIG welded zone was much shorter than that of the FS welded zone. The fatigue crack growth rate (FCGR) was retarded in the
APA, Harvard, Vancouver, ISO, and other styles
3

Allameh, S. M., C. Mercer, D. Popoola, and W. O. Soboyejo. "Microstructural Characterization of Ultrasonically Welded Aluminum." Journal of Engineering Materials and Technology 127, no. 1 (2005): 65–74. http://dx.doi.org/10.1115/1.1836792.

Full text
Abstract:
The microstructure and mechanical properties of ultrasonically welded AA6111-T4 specimens are discussed. The effects of welding time on the mechanical properties of welded joints are investigated. A longer welding time results in a more continuous welded interface and higher yield and fracture strengths. Accordingly, fatigue properties of the welded specimens with longer welding times are improved. The results of electron microscopy on the cross section of ultrasonically welded joints show three distinct zones: weld zone, weld affected zone and compression zone each with a distinct microstruct
APA, Harvard, Vancouver, ISO, and other styles
4

Abramov, A. D., A. S. Ilinykh, M. S. Galay, and Je S. Sidorov. "Investigation of Thermal Conditions of the Aluminothermic Welding and their Influence on the Structure and Properties of Metal Rails." Materials Science Forum 906 (September 2017): 50–55. http://dx.doi.org/10.4028/www.scientific.net/msf.906.50.

Full text
Abstract:
Rail welded joints are integral part of continuous welded rail. However, they often do not have sufficient reliability during the operation. The article is devoted to the assessment of temperature influence effect on the mechanical properties and structure of weld metal and welded rails. The temperature distribution across the rail section in welded zone during the cooling process of aluminothermic rail welding is obtained using simulation by LVMFlow. The results of the study of hardness and structure of metal rail aluminotermitic welded joints are given. It is shown that the hardness of rail
APA, Harvard, Vancouver, ISO, and other styles
5

Mahdi, Elsadig, E. Eltai, Fatima Ghassan Alabtah, and Faysal Fayez Eliyan. "Mechanical Characterization of AA 6061-T6 MIG Welded Aluminum Alloys Using a Robotic Arm." Key Engineering Materials 913 (March 18, 2022): 271–78. http://dx.doi.org/10.4028/p-rhrr3n.

Full text
Abstract:
Aluminum alloys are of particular interest in the design of lightweight structures in different applications. Accordingly, welding aluminum alloys (AA) is a critical issue; for example, welding defects could arise during the traditional welding of aluminum alloys. This paper investigates the effects of welding using a robotic arm on the mechanical properties of 6061-T6 Aluminum alloy, as plates joined by Metal Inert Gas (MIG) welding. The tensile behavior and mechanical properties were investigated using tensile testing, hardness testing, and impact testing. The tensile behavior of AA-6061-T6
APA, Harvard, Vancouver, ISO, and other styles
6

Chen, Yu Hua, Li Ming Ke, Ying Liu, and Shi Long Xu. "Study on the Microstructure of Micro Laser Welded Joint of TiNi Shape Memory Alloy Sheet." Advanced Materials Research 97-101 (March 2010): 3936–39. http://dx.doi.org/10.4028/www.scientific.net/amr.97-101.3936.

Full text
Abstract:
Butt welding of 0.2mm thick TiNi shape memory alloy sheet was successfully realized by using micro impulse laser whose average power is 80W and the microstructure of welded joint was study in this paper. The results show that, the welded joint of micro laser welding can be divided into four zones according to grain size and microstructure. The microstructure in base metal zone is rolled structure and the grains are coarse and heterogeneous. The microstructures of welded seam center zone are fine equiaxed crystals and the microstructures of both lower surface and upper surface edge zone are col
APA, Harvard, Vancouver, ISO, and other styles
7

Praunseis, Zdravko, Marko Mlakar, and Sonja Novak. "DETERMINATION OF LOCAL BRITTLE ZONES AT THE CRACK FRONT IN THE HAZ OF WELDED JOINT." Journal of Energy Technology 8, no. 4 (2024): 11–22. https://doi.org/10.18690/jet.8.4.11-22.2015.

Full text
Abstract:
Welded joints are the weakest link in the construction of steel structures. The brittlest part of a multi-pass welded joint is the heat-affected zone, where brittle fractures of the structure often appear. In this article, examination of the whole heat-affected zone of high strength multipass X welded joints was performed. All microstructures and the local brittle zones’ sizes at the crack tip front were precisely determined
APA, Harvard, Vancouver, ISO, and other styles
8

Ma, Yu E., and Zhen Qiang Zhao. "Investigation on the Corrosion Effect of Friction Stir Welded AA2024 T3 Aluminum Alloy Joints." Key Engineering Materials 525-526 (November 2012): 129–32. http://dx.doi.org/10.4028/www.scientific.net/kem.525-526.129.

Full text
Abstract:
Before friction stir welded integral panels are used in main aircraft structure, the corrosion behavior of welded joint need to be studied in detail. 2024 T3 samples were designed and welded by friction stir welding; the microstructure crossing the weld zone was observed by scanning electron microscopy (SEM), the feature of different zones (base material, thermo-mechanical affected zone, nugget) was seen; the corrosion testing in NaCl smoking box was carried out, and microstructure was observed after corrosion, localized corrosion predominantly occurs in the thermo-mechanical affected zone.
APA, Harvard, Vancouver, ISO, and other styles
9

Shchapov, G. V., and N. V. Kazantseva. "Comparative analysis of the chemical composition and mechanical properties of duralumin welded joint produced by friction stir welding." Frontier materials & technologies, no. 2 (2024): 113–19. http://dx.doi.org/10.18323/2782-4039-2024-2-68-10.

Full text
Abstract:
Friction stir welding is an advanced method of joining various metals and alloys in the aircraft and mechanical engineering industries. This type of welding is used to join materials that are difficult to weld or not weldable by conventional methods. The high-strength D16 aluminum alloy is difficult to weld by fusion, which is associated with the formation of a dendritic structure in the fusion zone leading to a decrease in the mechanical strength of the joint. In the work, the microstructure and microhardness of a welded seam of the D16 aluminum alloy produced by friction stir welding was stu
APA, Harvard, Vancouver, ISO, and other styles
10

Djili, Abderrahmane, Boudjema Bezzazi, Mohamed Habouss, and Nadjet Zioui. "Assessment of friction stir welding joints of AA2017-T4 aluminum by disc pressure mechanical tests." Journal of Applied Engineering Science 21, no. 2 (2023): 577–86. http://dx.doi.org/10.5937/jaes0-41037.

Full text
Abstract:
Precipitation hardening aluminium alloy sheets AA2017-T4 are welded by FSW on a conventional FSW tool. A macrograph of the cross section of the butt-welded joint shows the classical zones for such welding, namely the nugget zone, the thermo-mechanically affected zone and the heat affected zone. Scanning Electron Microscopy displays a grain refining and a re-formation of the precipitates in the nugget zone. Micro-hardness measurements on the cross-section perpendicular to the welding direction give the standard W-profile of the hardness for such welding, with as expected, the relatively highest
APA, Harvard, Vancouver, ISO, and other styles
11

Bisong, M. S., P. V. Sivtsev, and V. V. Lepov. "Numerical Analysis of Stress-Strain State and Crack Propagation in Welded Samples." Solid State Phenomena 265 (September 2017): 507–12. http://dx.doi.org/10.4028/www.scientific.net/ssp.265.507.

Full text
Abstract:
The numerical analysis of stress-strain state of low-alloyed welded steel samples test has been considered. The mechanical heterogeneity has been estimated by the micro hardness test. The stress-strain state analysis is based on the models of linear elasticity, which are described by Lame equations for displacement. In this case the samples are considered as perfect welded samples without any welding defects. The discretization of the system of equations is done through the finite element method, and the numerical realization of the method is performed on collection of free software FEniCS. Th
APA, Harvard, Vancouver, ISO, and other styles
12

Wang, Lyuyuan, Jian Huang, Yong Peng, Yang Jia, and Rong Ni. "Influence of heat treatment on corrosion behavior of laser welded Mg-Gd-Y fusion zones." Anti-Corrosion Methods and Materials 67, no. 4 (2020): 337–43. http://dx.doi.org/10.1108/acmm-10-2019-2194.

Full text
Abstract:
Purpose This paper aims to evaluate the corrosion resistance of fusion zones in different heat treated condition from laser welded Mg-Gd-Y alloys and analyze their intrinsic corrosion mechanism. Design/methodology/approach The corrosion behavior of fusion zone from laser-welded Mg-Gd-Y alloy joints in the as-welded, ageing and solution + ageing conditions was investigated in the 3.5 wt.% NaCl solution by immersion tests. Findings The corroded surface of as-welded fusion zone consists of dark and bright regions, and the bright regions were composed of high-density needle-like products, whereas
APA, Harvard, Vancouver, ISO, and other styles
13

Hongda, Deng, and Zeng Shunpeng. "Corrosion of welded joints of bimetallic composite tube in simulated offshore gas field environment." Anti-Corrosion Methods and Materials 61, no. 6 (2014): 380–86. http://dx.doi.org/10.1108/acmm-08-2013-1295.

Full text
Abstract:
Purpose – The purpose of this investigation was to research the corrosion behavior of welded joints of bimetallic composite tube (X65/316L) welded with Inconel 625 in simulated sea water and in simulated production water, respectively. Design/methodology/approach – The different electrochemical corrosion and galvanic corrosion behaviors of different welded zones were identified using the dynamic potential scan method and galvanic corrosion technique. Findings – The heat-affected zone (HAZ) of welded joints was the most critical zone for corrosion. The closer to the welding line, more severe wa
APA, Harvard, Vancouver, ISO, and other styles
14

Deng, Lipeng, Shuhan Li, Liming Ke, Jinhe Liu, and Jidong Kang. "Microstructure and Fracture Behavior of Refill Friction Stir Spot Welded Joints of AA2024 Using a Novel Refill Technique." Metals 9, no. 3 (2019): 286. http://dx.doi.org/10.3390/met9030286.

Full text
Abstract:
Keyhole at the end of a conventional friction stir welded (FSW) joint is one of the major concerns in certain applications. To address this issue, a novel keyhole refilling technique was developed for conventional friction stir spot welding (FSSW) using resistance spot welding (RSW). A three-phase secondary rectifier resistance welder was adapted for the refill of the keyhole in the 1.5 mm + 1.5 mm friction stir spot welded 2024-T4 aluminum alloy joint. The microstructure and tensile shear fracture behavior were compared for both the unfilled and refilled specimens. The results show that the p
APA, Harvard, Vancouver, ISO, and other styles
15

Laukhin, Dmytro, Valerii Poznyakov, Valery Kostin, et al. "Features in the formation of the structural state of low-carbon micro-alloyed steels after eletron beam welding." Eastern-European Journal of Enterprise Technologies 3, no. 12 (111) (2021): 25–31. http://dx.doi.org/10.15587/1729-4061.2021.234783.

Full text
Abstract:
Welding thermomechanically-strengthened materials is accompanied with certain difficulties in terms of loss of strength characteristics in the zone of thermal influence. This issue can be resolved by using the technological welding schemes that include fusion of materials in a narrow contact area. One such technological scheme is electron beam welding, which is currently widely used to fabricate structures from refractory and chemically active materials. One of the main advantages of the electron beam welding process is a small quantity of heat input, which leads to the formation of narrow zon
APA, Harvard, Vancouver, ISO, and other styles
16

Skowrońska, Beata, Tomasz Chmielewski, Dariusz Golański, and Jacek Szulc. "Weldability of S700MC steel welded with the hybrid plasma + MAG method." Manufacturing Review 7 (2020): 4. http://dx.doi.org/10.1051/mfreview/2020001.

Full text
Abstract:
The paper describes the microstructure of welded joints produced by the plasma+MAG (Metal Active Gas) method of S700MC high yield strength steel (700 MPa). Welded joints of thermomechanical steel have been made with different values of heat input. The results of metallographic research of welded joints, microstructure of the weld and heat affected zone, hardness distribution and impact toughness are presented. The heat affected zone consists of two sub-zones with different grain size and lowered hardness. The tensile test show that strength of welded joints was slightly reduced and the bending
APA, Harvard, Vancouver, ISO, and other styles
17

Ding, Xiao, and Xiang Li. "Influence of High-Temperature Ageing on the Microstructure of Stainless Steel/Low Alloy Steel Clad Plate Welded Joints." Materials Science Forum 878 (November 2016): 38–41. http://dx.doi.org/10.4028/www.scientific.net/msf.878.38.

Full text
Abstract:
This paper studies the microstructure of welded joints of Q345R/304 stainless steel clad plates after high temperature ageing. E309Nb welding rod, ER310 welding wire, and ER309L welding wire were used as cladding filling materials, and ER50-6 welding wire was used as base-layer filling material for welding. The metallographic microstructure of welding joints were studied after ageing treatment at 600°C for 100 hours. Test results showed that the microstructures of cladding weld zone were austenite and ferrite, and the ferrite in cladding weld zone of ER309L welded joints is less than the one i
APA, Harvard, Vancouver, ISO, and other styles
18

Wang, Xiao Ming, Sheng Zhu, Zhi Hao Zhao, Qi Wei Wang, and Xiao Dong Zhao. "Effect of Micro-Alloyed Treatment for 5183 Welding Wire on Microstructure and Tensile Property of Welded Joint." Applied Mechanics and Materials 633-634 (September 2014): 821–25. http://dx.doi.org/10.4028/www.scientific.net/amm.633-634.821.

Full text
Abstract:
5183 welding wire micro-alloyed using Sc, Zr, Er and automatic MIG welding system applied to weld 7A52 aluminum alloy. Optical microscope and universal tensile testing machine utilized to investigate microstructure and tensile property of welded joint, respectively. The results indicated that welded zone and fused zone was composed of uniform isometric crystal and tiny isometric dendrite crystal when the welded joint was fabricated by using 5183 welding wire micro-alloyed via rare earth element, respectively. Tensile strength and specific elongation of welded zone was improved utmostly when th
APA, Harvard, Vancouver, ISO, and other styles
19

Soltysiak, Robert. "Tests of Fracture Toughness of Laser-Welded Joints Made of Duplex 2205 Steel." Solid State Phenomena 250 (April 2016): 191–96. http://dx.doi.org/10.4028/www.scientific.net/ssp.250.191.

Full text
Abstract:
The process of welding introduces geometric notches to the area of joined material in the form of a face and root of a weld as well as structural heterogeneity in the form of changed properties (as compared with the parent material) in the heat affected zone and the weld zone. The parent material, as compared with the zones formed by welding, may differ in fracture toughness. In this paper the results of tests of fracture toughness of DUPLEX 2205 steel laser-welded joints are presented. Butt-welded joints were made by use of an Nd-YAG disc laser with no filler. The fatigue crack was initiated
APA, Harvard, Vancouver, ISO, and other styles
20

Patel, Vinay Kumar, and Komal Rani. "Mechanical and Wear Properties of Friction Stir Welded 0–6Wt% nAl2O3 Reinforced Al-13Wt%Si Composites." Strojnícky casopis – Journal of Mechanical Engineering 67, no. 1 (2017): 77–86. http://dx.doi.org/10.1515/scjme-2017-0008.

Full text
Abstract:
Abstract Friction Stir Welding (FSW) of an Al-13%Si alloy matrix reinforced with 0, 3 and 6 wt% Al2O3 nanoparticles (nAl2O3) is performed and the optical microstructures, tensile strength, hardness and sliding wear properties of friction stir welded joints are investigated and compared to those of base materials. Four different zones of distinct appearances were observed during FSW, which exhibited altered microstructures in the nugget zone (NZ), thermo mechanically affected zone (TMAZ), heat affected zone (HAZ), and base material zone (BMZ). The ultimate tensile strength of the base materials
APA, Harvard, Vancouver, ISO, and other styles
21

Liu, Ge Ping, Yu Hua Chen, Hong Yan Wu, and Li Ming Ke. "Study on the Microstructure and Properties of Zl114a Friction Stir Welded Joint with Forced Cooling." Advanced Materials Research 189-193 (February 2011): 3335–38. http://dx.doi.org/10.4028/www.scientific.net/amr.189-193.3335.

Full text
Abstract:
ZL114A was joined by friction stir welding and liquid nitrogen was used to cool the welded joint during the welding process. The Influence of forced cooling on the microstructure and properties of welded jointed was studied. The results show that, when forced cooling is used, the amount of silicon particles in weld nugget zone is larger and the size is more homogeneous, the size of silicon particle in heat-mechanical affected zone is more fine , the grain size of heat affected zone is half of air cooling welded joint and the amount of Al-Si eutectic is smaller than air cooling welded joint. Th
APA, Harvard, Vancouver, ISO, and other styles
22

Guo, Yanning, and Wenbo Sun. "Study on Mechanical Properties and Microstructure of 2024 Aluminum Alloy Cross-Welded Joint by Friction Stir Welding." Materials 18, no. 10 (2025): 2223. https://doi.org/10.3390/ma18102223.

Full text
Abstract:
The integral welded panel represents a highly promising aircraft structural component, owing to its lightweight design and reduced connector requirements. However, the complexity of its welded structure results in the formation of cross-welded joints. This study systematically investigated the mechanical properties of the cross-welded joints through tensile tests across different welded regions, which were complemented by fracture morphology examination via scanning electron microscopy (SEM). The residual stress distribution was characterized using X-ray diffraction, while electron backscatter
APA, Harvard, Vancouver, ISO, and other styles
23

Kozyrev, N. A., R. A. Shevchenko, A. A. Usol'tsev, R. E. Kryukov, and A. R. Mikhno. "Study of wear resistance of railway rails welded joint." Ferrous Metallurgy. Bulletin of Scientific , Technical and Economic Information 76, no. 8 (2020): 818–25. http://dx.doi.org/10.32339/0135-5910-2020-8-818-825.

Full text
Abstract:
Welding joints of rails are a weak point of a jointless railway line, which stipulates actuality of studies on increasing their operational resistance. Microstructures of welded joints made by existing at present welding technology and by a new one were compared. Existing (base) technology comprises further thermal treatment of the welded joint, while the new technology comprises welding followed by a short-time electric current impact during the rail joint cooling. To study the microstructures of welded joints, samples were cut out the welded seam zone and heat affected zone, as well as out o
APA, Harvard, Vancouver, ISO, and other styles
24

Dmytro, Laukhin, Poznyakov Valerii, Kostin Valery, et al. "Features in the formation of the structural state of low-carbon micro-alloyed steels after eletron beam welding." Eastern-European Journal of Enterprise Technologies 3, no. 12(111) (2021): 25–31. https://doi.org/10.15587/1729-4061.2021.234783.

Full text
Abstract:
Welding thermomechanically-strengthened materials is accompanied with certain difficulties in terms of loss of strength characteristics in the zone of thermal influence. This issue can be resolved by using the technological welding schemes that include fusion of materials in a narrow contact area. One such technological scheme is electron beam welding, which is currently widely used to fabricate structures from refractory and chemically active materials. One of the main advantages of the electron beam welding process is a small quantity of heat input, which leads to the formation of narrow zon
APA, Harvard, Vancouver, ISO, and other styles
25

Yu, Si Rong, and Xian Jun Chen. "Microstructures and Properties of FSW Joints of AZ31B Mg Alloy." Advanced Materials Research 291-294 (July 2011): 855–59. http://dx.doi.org/10.4028/www.scientific.net/amr.291-294.855.

Full text
Abstract:
The extruded AZ31B Mg alloy sheet was welded with friction stir welding. The microstructures and mechanical properties of the welded joint were investigated. The results show that the grains in the weld nugget zone were small, uniform and equiaxed. The grains in thermo-mechanical affected zone were stretched and relatively small, but were not as small and uniform as those in the weld nugget zone. The grains in the heat-affected zone were relatively coarse. The fracture of the welded joint occurred mainly in the heat affected zone. The tensile strength of the welded joints was up to 257.4 MPa a
APA, Harvard, Vancouver, ISO, and other styles
26

Liu, Peng, Shanguo Han, Yaoyong Yi, and Cuixia Yan. "Corrosion Behavior of Welded Joint of Q690 with CMT Twin." International Journal of Corrosion 2018 (July 4, 2018): 1–9. http://dx.doi.org/10.1155/2018/2368717.

Full text
Abstract:
Low alloy steel of Q690 was welded with the method of CMT Twin. The corrosion behavior of welded joint had been investigated using scanning vibrating electrode technique (SVET) in 3.5% NaCl solution. The research results showed that the appearance of the troostite increased the hardness of the heat affected zone. Furthermore, the corrosion products of different microstructure were identical, and the white products (Fe(OH)2) of welded joint turned into products of rufous (Fe(OH)3). The quantitative information provided by SVET was discussed, and the corrosion degree was measured by some paramet
APA, Harvard, Vancouver, ISO, and other styles
27

Błacha, S., M. S. Węglowski, S. Dymek, and M. Kopyściański. "Microstructural and Mechanical Characterization of Electron Beam Welded Joints of High Strength S960QL and Weldox 1300 Steel Grades." Archives of Metallurgy and Materials 62, no. 2 (2017): 627–34. http://dx.doi.org/10.1515/amm-2017-0092.

Full text
Abstract:
Abstract The paper shows the results of metallographic examination and mechanical properties of electron beam welded joints of quenched and tempered S960QL and Weldox 1300 steel grades. The aim of this study was to examine the feasibility of producing good quality electron beam welded joints without filler material. Metallographic examination revealed that the concentrated electron beam significantly affects the changes of microstructure in the weld and the adjacent heat affected zone (HAZ) in both steel grades. The microstructure of the welded joints is not homogeneous. The four zones, depend
APA, Harvard, Vancouver, ISO, and other styles
28

Herrera-Chávez, Lourdes Y., Alberto Ruiz, Víctor H. López-Morelos, Carlos Rubio-González, Martín R. Barajas-Álvarez, and Arnoldo Bedolla Jacuinde. "Microstructural and mechanical characterization of the effect of the welding process on creep behavior of welded joint and base metal specimens of Inconel 600." MRS Advances 5, no. 59-60 (2020): 3003–14. http://dx.doi.org/10.1557/adv.2020.407.

Full text
Abstract:
AbstractIn this study, plates of Inconel 600 superalloy were gas metal arc welded to investigate the effects of the welding process on the creep behavior of the welded samples and compare it to the creep behavior of samples in the as-received condition. Creep tests were performed at two temperatures (600 and 650 °C) with different stress levels. During the welding process, three distinctive microstructural zones are generated, i.e. welded material, heat affected zone, and base metal that may affect the properties of the welded joint. Microstructural, elemental analysis of samples was conducted
APA, Harvard, Vancouver, ISO, and other styles
29

Shankar, M. P., R. Sokkalingam, Bhavani Kosuri, K. Sivaprasad, and V. Muthupandi. "Effect of Welding Speed on the Microstructure and Corrosion Properties of Weld and Heat Affected Zones in GTA Welded AA2014 Alloy." Materials Science Forum 969 (August 2019): 834–38. http://dx.doi.org/10.4028/www.scientific.net/msf.969.834.

Full text
Abstract:
The microstructure and corrosion properties of weld fusion zone and the heat affected zones of gas tungsten arc (GTA) welded AA2014 alloy, welded at varying speeds of 1.5mm/s, 2.5 mm/s and 3.5 mm/s were examined for gaining knowledge on the effect of welding speed on corrosion behavior at localized regions of the weldment. The macrostructure and microstructure of the welds were evaluated with optical microscope. The corrosion properties were examined with potentiodynamic polarization in aqueous 3.5% NaCl solution. The GTA welding has resulted in grain refinement fusion zone and dispersion of c
APA, Harvard, Vancouver, ISO, and other styles
30

Cao, Fang Li, Guo Qin Sun, and Jiang Pei Niu. "Research on Microstructure of Aluminum 2219-T6 Friction Stir Welded Joint." Advanced Materials Research 968 (June 2014): 133–37. http://dx.doi.org/10.4028/www.scientific.net/amr.968.133.

Full text
Abstract:
Friction stir weld fatigue test was performed and the microstructure of the welded joint was analyzed on aluminum 2219-T6. The surface morphology, micro-hardness and grain structure of the welded joint were observed. The fracture surface of the welded joint was observed after the fatigue test. According to the observations, there were more dynamic recrystallizations in the nugget zone and the grain size became smaller in this zone. The grains in the thermo-mechanical affected zone deformed obviously and there were more substructures in the heat affected zone. The hardness values were lower in
APA, Harvard, Vancouver, ISO, and other styles
31

Tomerlin, Damir, Dražan Kozak, Luka Ferlič, and Nenad Gubeljak. "Experimental and Numerical Analysis of Fracture Mechanics Behavior of Heterogeneous Zones in S690QL1 Grade High Strength Steel (HSS) Welded Joint." Materials 16, no. 21 (2023): 6929. http://dx.doi.org/10.3390/ma16216929.

Full text
Abstract:
The heterogeneity of welded joints’ microstructure affects their mechanical properties, which can vary significantly in relation to specific weld zones. Given the dimensional limitations of the available test volumes of such material zones, the determination of mechanical properties presents a certain challenge. The paper investigates X welded joint of S690QL1 grade high strength steel (HSS), welded with slightly overmatching filler metal. The experimental work is focused on tensile testing to obtain stress-strain properties, as well as fracture mechanics testing. Considering the aforementione
APA, Harvard, Vancouver, ISO, and other styles
32

Zhang, Ci, Yinsheng He, and Wenyue Zheng. "Stress-Corrosion-Cracking Sensitivity of the Sub-Zones in X80 Steel Welded Joints at Different Potentials." Materials 17, no. 14 (2024): 3481. http://dx.doi.org/10.3390/ma17143481.

Full text
Abstract:
X80 steel plays a pivotal role in the development of oil and gas pipelines; however, its welded joints, particularly the heat-affected zone (HAZ), are susceptible to stress corrosion cracking (SCC) due to their complex microstructures. This study investigates the SCC initiation mechanisms of X80 steel welded joints under practical pipeline conditions with varying levels of cathodic protection. The SCC behaviors were analyzed through electrochemical measurements, hydrogen permeation tests, and interrupted slow strain rate tensile tests (SSRTs) conducted in a near-neutral pH environment under di
APA, Harvard, Vancouver, ISO, and other styles
33

Fabian, Eniko Reka, Janos Kuti, Jozsef Gati, and Laszlo Toth. "Corrosion Behavior of Welded Joints in Different Stainless Steels." Revista de Chimie 71, no. 3 (2001): 440–49. http://dx.doi.org/10.37358/rc.20.3.8018.

Full text
Abstract:
The welded metals characteristics produced by TIG welding or laser beam welding depend on heat input as a function of laser power and welding speed. High laser power and high welding speed have produced welded joint with a remarkable decrease in fusion zone size and an acceptable weld profile with high weld depth/width ratio. At duplex stainless steels the microstructure of welded metal, and heat affected zone is strongly influenced by cooling rate, which is depend on heat input as a function of laser power and/or welding speed. It was found that increasing welding speed the corrosion rate of
APA, Harvard, Vancouver, ISO, and other styles
34

He, Chao, Shi Ming Cui, Yan Zeng Wu, Ze Fu Luo, and Qing Yuan Wang. "Fatigue Crack Initiation Mechanism of Aluminium Alloy Welded Joint in Gigacycle Fatigue." Applied Mechanics and Materials 376 (August 2013): 177–80. http://dx.doi.org/10.4028/www.scientific.net/amm.376.177.

Full text
Abstract:
Ultrasonic fatigue test was performed on 5052 aluminium alloy welded joint to investigate the very high cycle fatigue properties and the fatigue crack initiation mechanisms with the help of microhardness tester and scanning electron microscope (SEM). The results showed that the hardness of fusion zone was higher that base metal and heat affected zone, which led to the embrittlement of welded zone. Fusion zone became the weakest part of welded joint under cyclical loading. Fatigue crack usually initiated from the pores beneath the surface from the SEM observation of fracture surface. The influe
APA, Harvard, Vancouver, ISO, and other styles
35

Lee, Yong-Jae, Won-Ki Jung, Se-Eun Shin, and Dong-Geun Lee. "Effects of Rotation Speed on Microstructure and Mechanical Properties in Ti/Cu Dissimilar Friction Stir Welding." Korean Journal of Metals and Materials 59, no. 12 (2021): 886–92. http://dx.doi.org/10.3365/kjmm.2021.59.12.886.

Full text
Abstract:
The dissimilar welding of titanium and copper by fusion welding is very difficult because the melting points of the materials are very highly different and strong brittle intermetallic compounds (IMCs) can be easily produced in welded zone and heat-affected zone, etc. Friction stir welding was employed as a type of solid-state welding for Ti/Cu dissimilar welding to obtain a sound welded zone and reduce the total process cost. This study investigated how the metal flow of the welded zone changes according to the variation in the rotational speed of the tool, from 450 rpm to 600 rpm. When the r
APA, Harvard, Vancouver, ISO, and other styles
36

Hamdi, Ines, Zakaria Boumerzoug, Oualid Bedjaoui, Wafa Melik, and Fabienne Delaunois. "Thermal Cycle Simulation of Heat Affected Zone in the Welded Mild Steel." Key Engineering Materials 981 (May 14, 2024): 43–50. http://dx.doi.org/10.4028/p-4rswbo.

Full text
Abstract:
The aim of this work was to study the microstructure evolution of simulated heat affected zone in mild steel using thermal cycle simulation and it was compared to the heat affected zone in the real welded joint. The optical microscopy, micro-hardness measurements, X-ray diffraction were used as characterization techniques. The microstructures and mechanical properties of the simulated heat affected zone were also determined. The use of the thermal cycle simulation technique revealed in detail the different microstructures in the heat affected zone (HAZ) of the welded joint. Some similarities w
APA, Harvard, Vancouver, ISO, and other styles
37

Liu, Pengtao, Runze Yu, Xinhuan Gao, and Guanzhen Zhang. "Influence of Surface Ultrasonic Rolling on Microstructure and Corrosion Property of T4003 Ferritic Stainless Steel Welded Joint." Metals 10, no. 8 (2020): 1081. http://dx.doi.org/10.3390/met10081081.

Full text
Abstract:
In this paper, the effect of surface ultrasonic rolling treatment (SURT) on surface properties of T4003 cold metal transfer (CMT) welded joints was studied. Surface topography and microstructure changes of the welded joint surface before and after SURT were observed by optical microscope and scanning electron microscope. The hardness and residual stress distribution of welded joint were measured by a microhardness tester and X-ray diffractometer. The change of corrosion resistance of welded joints was studied by electrochemical polarization curve measurement. The results show that surface roug
APA, Harvard, Vancouver, ISO, and other styles
38

Wang, Yan. "Study on Behavior of CO2 Gas Shielded Welding Joint of Ultrafine Grain Steel." Journal of Physics: Conference Series 2393, no. 1 (2022): 012008. http://dx.doi.org/10.1088/1742-6596/2393/1/012008.

Full text
Abstract:
Abstract This research paper mainly studied the microstructure and hardness of the weld bead and welding heat affected zone of ultrafine grain steel after CO2 gas-shielded welding. After normalizing and quenching heat treatment, the changes in microstructure and hardness of welded joints were studied. These experimental results showed that the microstructure of the weld bead of the welded joint was dendritic. The microstructure of weld bead was a mixed structure of proeutectoid ferrite, side plate ferrite, bainite, and pearlite. The microstructure of the overheated zone of HAZ under the as-wel
APA, Harvard, Vancouver, ISO, and other styles
39

Tian, Qing Chao, Xian Ping Dong, Hai Chao Cui, and Ke Xu. "Characterization of the Welded-Joint of High-Strength High-Toughness Seamless Steel Pipe under High-Cycle Fatigue Condition." Materials Science Forum 896 (March 2017): 202–8. http://dx.doi.org/10.4028/www.scientific.net/msf.896.202.

Full text
Abstract:
The welded joint of a S890QL grade steel pipes containing 1.2% Ni have been prepared to characterize the use performance under high cycle fatigue test. It has been found that the fatigue strength of the welded joint is 290MPa with a fatigue life of more than 10 million cycles, and the obtained Basquin equation is σa=488*(2N)-0.02758 . It is found that the steel exhibits the whole bainite microstructure when the cooling rate is less than 1°C/s. The welded joint is divided into the weld zone, the coarse grain zone, the fine grain zone, the softening zone and the matrix. The fine grain characteri
APA, Harvard, Vancouver, ISO, and other styles
40

Wang, Xueli, Dongpo Wang, Caiyan Deng, and Chengning Li. "Effect of H2S Corrosion on the Fracture Toughness of the X80 Pipeline Steel Welded Joint." Materials 15, no. 13 (2022): 4458. http://dx.doi.org/10.3390/ma15134458.

Full text
Abstract:
To analyze the causes and mechanisms affecting the fracture toughness of X80 pipeline steel welded joints against H2S, the fracture toughness of different zones of X80 pipeline steel welded joints in both air and saturated H2S solution was investigated. The fracture toughness of welded joints degraded significantly in the saturated H2S solution, where the crack tip opening displacement (CTOD) characteristic value in the coarse grain heat-affected zone (CGHAZ) and weld metal (WM) was only 8% and 12% of that in air, respectively. However, the sub-critical grain heat-affected zone (SCHAZ) showed
APA, Harvard, Vancouver, ISO, and other styles
41

Schramkó, Márton, Zoltán Nyikes, Hassanen Jaber, and Tünde Anna Kovács. "Dissimilar Joining by Ultrasonic Welding." Journal of Hunan University Natural Sciences 49, no. 3 (2022): 185–91. http://dx.doi.org/10.55463/issn.1674-2974.49.3.20.

Full text
Abstract:
Ultrasonic welding is a rapid process for thin sheet joining. The authors wanted to show the aluminum-copper dissimilar joining by the ultrasonic welding process in this work. Ultrasonic welding is a suitable and straightforward process to establish dissimilar joints between different metals. The goal was to investigate the ultrasonic welding complex effect on the material properties. Ultrasonic welding is solid-state welding, which uses pressure, friction, ultrasound effect to establish a metallic joint. The complex effects are the friction heat, the pressure caused plastic deformation, and t
APA, Harvard, Vancouver, ISO, and other styles
42

Urminský, Ján, Milan Marônek, Jozef Bárta, Martin Sahul, František Jurina, and Matej Pašák. "Electron Beam Welding of Aluminium Alloy AW2099." Materials Science Forum 994 (May 2020): 28–35. http://dx.doi.org/10.4028/www.scientific.net/msf.994.28.

Full text
Abstract:
The paper deals with the analysis of mechanical properties of welded joints made of AW 2099 aluminium-lithium alloy by electron beam welding. The thickness of the experimental material was 3±0.2 mm. PZ EZ 30 STU electron beam welding machine was used for production of welds. Maximum accelerating voltage used within this study was 55 kV. Metallographic analysis, hardness measurement test and static tensile were carried out. The structure of the weld joint of aluminium-lithium alloy was investigated. Produced welded joints were characterized by the presence of following zones: heat affected zone
APA, Harvard, Vancouver, ISO, and other styles
43

Laukhin, Dmytro, Valerii Pozniakov, Oleksandr Beketov, Nataliia Rott, and Anatolii Shchudro. "Analysis of the Effects of Welding Conditions on the Formation of the Structure of Welded Joints of Low-Carbon Low-Alloy Steels." Key Engineering Materials 844 (May 2020): 146–54. http://dx.doi.org/10.4028/www.scientific.net/kem.844.146.

Full text
Abstract:
To obtain reliable joints in the conditions of open construction is complicated or impossible to use stationary machines and apparatuses, so requirements to welding processes are of special interest. The most interest concerning the support of strength and reliability of welded joint is specific processes developed after the crystallization of weld at weld zone. The value of the zone of thermal influence depends on the welding conditions and properties of metal that is welded. That is why the research on the influence of welding conditions on the formation of the structure of welded zone and t
APA, Harvard, Vancouver, ISO, and other styles
44

Mittal, Arvind, and Rajesh Gupta. "Effect of Heat input on Micro Hardness and Metallurgical Properties of Shield Metal ARC Welded Duplex Stainless Steel." Asian Journal of Science and Applied Technology 5, no. 1 (2016): 33–37. http://dx.doi.org/10.51983/ajsat-2016.5.1.2546.

Full text
Abstract:
The work was carried out to the effect of heat input on the hardness and metallurgical properties of shield metal arc welded of duplex stainless steel. Three specimen A, B and C with heat input combinations designated as low heat A (0.675 KJ/mm), medium heat B (0.860 KJ/mm) and high heat C (1.094 KJ/mm) and the weld joints made using these three combinations were subjected to observe the changes in thermal condition caused by variation of heat input can affect the metallurgical properties and the hardness of the welded joint. The result achieved from this research shows that the joints made us
APA, Harvard, Vancouver, ISO, and other styles
45

Zhu, Wen, Weijie Gou, and Lihong Wang. "Microstructure and performance test of aluminum alloy K-TIG welding joint." Advances in Engineering Technology Research 1, no. 2 (2022): 368. http://dx.doi.org/10.56028/aetr.1.2.368.

Full text
Abstract:
The K-TIG welding method was used to conduct welding experiments on 6001 aluminum alloy, and the microstructure and mechanical properties of the welded joints were studied by optical microscope, scanning electron microscope, universal testing machine, microhardness tester, etc. The results show that the center of the weld is equiaxed crystals and a small amount of dendrites, the near seam zone is columnar crystals formed by associated crystals, the fusion zone is equiaxed crystals of varying sizes, and there are grain boundary liquefaction and β″ phase in this zone. Agglomeration, growth and t
APA, Harvard, Vancouver, ISO, and other styles
46

Zhu, Wen, Weijie Gou, and Lihong Wang. "Microstructure and performance test of aluminum alloy K-TIG welding joint." Advances in Engineering Technology Research 2, no. 1 (2022): 368. http://dx.doi.org/10.56028/aetr.2.1.368.

Full text
Abstract:
The K-TIG welding method was used to conduct welding experiments on 6001 aluminum alloy, and the microstructure and mechanical properties of the welded joints were studied by optical microscope, scanning electron microscope, universal testing machine, microhardness tester, etc. The results show that the center of the weld is equiaxed crystals and a small amount of dendrites, the near seam zone is columnar crystals formed by associated crystals, the fusion zone is equiaxed crystals of varying sizes, and there are grain boundary liquefaction and β″ phase in this zone. Agglomeration, growth and t
APA, Harvard, Vancouver, ISO, and other styles
47

Boumerzoug, Z., Chérifa Bouremel, and V. Ji. "Residual Stress and Microstructures Characterization in Welded Al-Si-12Cu Alloy." Advanced Materials Research 856 (December 2013): 201–4. http://dx.doi.org/10.4028/www.scientific.net/amr.856.201.

Full text
Abstract:
X-ray diffraction method has been used to analyze the residual stress distribution across the joint of Al-Si-12Cu alloy just after welding process. On the other hand, isothermal heat treatments have been applied in order to study the residual stress evolution in this material. Optical microscope observation and Vickers hardness measurement have been carried out as complementary microstructure techniques. The different zones of welded joint have been analyzed, where the fusion zone was characterized by dendritic structure and different to heat affected zone. We have found a softening phenomenon
APA, Harvard, Vancouver, ISO, and other styles
48

Gu, Sen Dong, Ji Peng Zhao, Rui Jie Ouyang, and Yong Hong Zhang. "Microstructural Characterization and Tensile Behavior of TA1 Titanium Alloy Sheet Welded by Electron Beam Welding." Materials Science Forum 1027 (April 2021): 149–54. http://dx.doi.org/10.4028/www.scientific.net/msf.1027.149.

Full text
Abstract:
In the present study, TA1 titanium alloy sheets with a thickness of 0.8mm were welded by electron beam welding. Microstructure of the welded region was investigated using optical microscope and electron backscattered diffraction. Then, the tensile test was conducted to analyse the tensile behavior of the welded sheets as well as the fractography of the fracture surfaces. It is shown that the mean grain size in the heat-affected zone is smaller than that in the fusion zone and base material. The strength of the base metal is lower than that of the fusion zone and heat-affected zone. The average
APA, Harvard, Vancouver, ISO, and other styles
49

Lee, Sung Yul, Kyung Man Moon, Jong Pil Won, Jae Hyun Jeong, and Tae Sil Baek. "Characteristics of Inconel 625 Filler Metal Affecting to Weld and Deposited Metal Zones in the Case of Welded to Forged Steel for Piston Crown Material." Advanced Materials Research 1004-1005 (August 2014): 1114–19. http://dx.doi.org/10.4028/www.scientific.net/amr.1004-1005.1114.

Full text
Abstract:
Recently, wear and corrosion of the engine parts surrounded with combustion chamber is more serious compared to the other parts of the engine due to using of heavy oil of low quality. Therefore, an optimum repair welding for these parts is very important to prolong their lifetime in a economical point of view. In this study, Inconel 625 filler metal was welded with GTAW method in the forged steel which would be generally used with piston crown material. In this case, the mechanical and corrosion properties between weld metal zone (WM) welded to the groove which were artificially made in the ba
APA, Harvard, Vancouver, ISO, and other styles
50

Laukhin, Dmytro, Kyrylo Ziborov, Nataliia Rott, and Sergey Fedoryachenko. "Analysis of the Effects of Welding Conditions on the Microhardness of Low-Carbon Low-Alloy Steels." Materials Science Forum 1126 (September 27, 2024): 119–27. http://dx.doi.org/10.4028/p-ld0xwa.

Full text
Abstract:
Achieving dependable connections in open construction settings presents challenges or renders the use of stationary machines and equipment complicated, if not impossible. Therefore, there is a particular focus on the requirements for welding processes. Of particular interest is ensuring the strength and reliability of welded joints, especially through processes developed subsequent to the solidification of the weld at the weld zone. The extent of the thermal influence zone is contingent upon the welding conditions and the properties of the metal being welded. Hence, research into the impact of
APA, Harvard, Vancouver, ISO, and other styles
We offer discounts on all premium plans for authors whose works are included in thematic literature selections. Contact us to get a unique promo code!