Готові списки джерел за темами / Constructive placement

Добірка наукової літератури з теми "Constructive placement"

Автор: Grafiati

Опубліковано: 24 січня 2023

Оформте джерело за APA, MLA, Chicago, Harvard та іншими стилями

Оберіть тип джерела:

Ознайомтеся зі списками актуальних статей, книг, дисертацій, тез та інших наукових джерел на тему "Constructive placement".

Біля кожної праці в переліку літератури доступна кнопка «Додати до бібліографії». Скористайтеся нею – і ми автоматично оформимо бібліографічне посилання на обрану працю в потрібному вам стилі цитування: APA, MLA, «Гарвард», «Чикаго», «Ванкувер» тощо.

Також ви можете завантажити повний текст наукової публікації у форматі «.pdf» та прочитати онлайн анотацію до роботи, якщо відповідні параметри наявні в метаданих.

Статті в журналах з теми "Constructive placement":

Anderson, Eric J., and Matthew E. Brock. "Being in the Right Place at the Right Time: Educational Placement of Students With Intellectual Disability by State and Year." Inclusion 8, no. 3 (September 1, 2020): 210–21. http://dx.doi.org/10.1352/2326-6988-8.3.210.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Abstract Despite the longstanding federal mandate to place students with disabilities in general education classrooms to the maximum extent appropriate, most students with intellectual disability continue to spend most of their time in separate classrooms and schools. In this study, we describe longitudinal educational placement patterns in six states that represent the wide span of educational placement (i.e., Vermont, Kentucky, Kansas, Massachusetts, Illinois, and Montana). Surprisingly, some states are trending toward more restrictive placements, and the gap between the most and least inclusive states is continuing to widen over time. We offer constructive suggestions for appropriately applying the principle of least restrictive environment so that placement decisions are driven by student needs and not where students live.

Wimer, S., and I. Koren. "Analysis of strategies for constructive general block placement." IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems 7, no. 3 (March 1988): 371–77. http://dx.doi.org/10.1109/43.3170.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Saab, Youssef. "A Fast Clustering-Based Min-Cut Placement Algorithm With Simulated-Annealing Performance." VLSI Design 5, no. 1 (January 1, 1996): 37–48. http://dx.doi.org/10.1155/1996/58084.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Placement is an important constrained optimization problem in the design of very large scale (VLSI) integrated circuits [1–4]. Simulated annealing [5] and min-cut placement [6] are two of the most successful approaches to the placement problem. Min-cut methods yield less congested and more routable placements at the expense of more wire-length, while simulated annealing methods tend to optimize more the total wire-length with little emphasis on the minimization of congestion. It is also well known that min-cut algorithms are substantially faster than simulated-annealing-based methods. In this paper, a fast min-cut algorithm (ROW-PLACE) for row-based placement is presented and is empirically shown to achieve simulated-annealing-quality wire-length on a number of benchmark circuits. In comparison with Timberwolf 6 [7], ROW-PLACE is at least 12 times faster in its normal mode and is at least 25 times faster in its faster mode. The good results of ROW-PLACE are achieved using a very effective clustering-based partitioning algorithm in combination with constructive methods that reduce the wire-length of nets involved in terminal propagation.

da Silva, Ivo Chaves, Sandoval Carneiro, Edimar JosÉ de Oliveira, Jeferson de Souza Costa, JosÉ Luiz Rezende Pereira, and Paulo Augusto Nepomuceno Garcia. "A Heuristic Constructive Algorithm for Capacitor Placement on Distribution Systems." IEEE Transactions on Power Systems 23, no. 4 (November 2008): 1619–26. http://dx.doi.org/10.1109/tpwrs.2008.2004742.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Boykov, A. A. "BUILDING MODELS OF DYNAMIC CANAL SURFACES VIA GEOMETRY CONSTRUCTIONS LANGUAGE." Vestnik komp'iuternykh i informatsionnykh tekhnologii, no. 220 (October 2022): 15–29. http://dx.doi.org/10.14489/vkit.2022.10.pp.015-029.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Building computer models of dynamic canal surfaces is a special case when implemented in CAD-systems since existing methods of surface modeling of such type are concentrated mostly on obtaining analytical expressions such as equations for the surface itself or its sections. The article introduces a constructive method of building models based on plane and spatial geometric constructions. The paper provides the analysis of given surface parameters, constructive algorithms for setting up a geometric correspondence between the graph of the cross-sectional area and the directrix, constructing of cross-section for the given point on the cross-section area graph as well as placement the cross-sections in three dimensions and determining spatial coordinates of the points on the surface. This allows to build a structured point cloud of a dynamic canal surface of required density and build a model of it in CAD-systems. Suggested constructive algorithms are applied with the help of GC language commands. The paper provides fragments of construction subroutines as well as examples of created models of dynamic canal surfaces. The approach proposed provides for automation of building models of surfaces in CAD-systems, moreover it is flexible to adjust according to the given parameters such as a directrix shape, cross-section area graph, a cross-section shape, etc.

Bentley, Erinn, Madison Workman, and Alex Overby. "Being “adopted” into a teaching community." International Journal of Mentoring and Coaching in Education 6, no. 3 (September 4, 2017): 228–41. http://dx.doi.org/10.1108/ijmce-03-2017-0016.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Purpose In order to prepare new members of the education profession, it is imperative that teachers enter their classrooms with the confidence, knowledge, and skills to serve their students from day one. One method for preparing such teacher candidates or student teachers is through school-based field placements during their preparation program. The purpose of this paper is to describe one example of a yearlong field placement and the mentoring relationships that emerged among participants. Design/methodology/approach This qualitative study used the following data sources: focus group interviews among the teacher candidates, focus group interviews among the mentor teachers, field placement reflections and teaching analyses composed by the teacher candidates, and interviews conducted among teacher candidates and mentor teachers. Findings Analysis of the data revealed that the yearlong field placement promoted positive mentoring relationships between teacher candidates and their classroom teachers. Specifically the following themes emerged: the “adoption” of teacher candidates into the high school classrooms, risk-taking within the classrooms, the mentor teachers’ use of constructive feedback, and collaborative “mentoring-down-the-hall.” Originality/value In recent years, various scholars have investigated the impact of field placement experiences on teacher candidates; however, these studies have lacked a detailed analysis of how such experiences impacted mentoring relationships among candidates and their mentor teachers in a collaborative setting. This paper provides an in-depth study of the perceived experiences of mentor teachers and their candidates.

Alupoaei, Stelian, and Srinivas Katkoori. "Net Clustering Based Constructive and Iterative Improvement Approaches for Macro-Cell Placement." Journal of VLSI Signal Processing-Systems for Signal, Image, and Video Technology 37, no. 1 (May 2004): 151–63. http://dx.doi.org/10.1023/b:vlsi.0000017008.38412.54.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Waldron, Michelle, and Michael Byrne. "Clinical psychology trainees’ experiences of supervision." Clinical Psychology Forum 1, no. 255 (March 2014): 42–46. http://dx.doi.org/10.53841/bpscpf.2014.1.255.42.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

A survey of clinical psychology trainees profiled their experiences of clinical placement supervision and whether these facilitated development of their competencies. They also highlighted the importance of positive feedback and constructive criticism, reflective supervision, supervision reliability and acknowledgement of transference.

Wang, Bo Han, Jia Min Liu, Yong Yue, and Malcolm Keech. "A Constructive Heuristic for Two-Dimensional Bin Packing." Advanced Materials Research 756-759 (September 2013): 2705–10. http://dx.doi.org/10.4028/www.scientific.net/amr.756-759.2705.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Two-dimensional bin packing is encountered in various applications where small rectangular items are packed into a minimum number of large rectangular objects (bins). Aiming at an optimal area utilization, the paper presents an effective constructive heuristic approach to two-dimensional bin packing. The heuristic approach integrates ranking, placement and search strategies along with an effective handling method of the remaining areas during the packing process. In order to obtain an optimal arrangement in a given area, all items are examined for possible positions and orientations using the search strategies. In addition, an effective handling method of the remaining areas is applied through appropriate partitioning and merging to minimize waste areas. Tests with a number of standard test and real world instances have shown that the performance of the proposed approach is superior to that of other approaches published.

Gomes, Sóstenes Pereira, Luiz Antonio Nogueira Lorena, and Glaydston Mattos Ribeiro. "A Constructive Genetic Algorithm for Discrete Dispersion on Point Feature Cartographic Label Placement Problems." Geographical Analysis 48, no. 1 (August 12, 2015): 43–58. http://dx.doi.org/10.1111/gean.12082.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Більше джерел

Дисертації з теми "Constructive placement":

Kennings, Andrew A. "Cell placement using constructive and iterative improvement methods." Thesis, National Library of Canada = Bibliothèque nationale du Canada, 1997. http://www.collectionscanada.ca/obj/s4/f2/dsk3/ftp04/nq21359.pdf.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Song, Xiaoxiao. "Layout optimization based on multi-objective interactive approach." Thesis, Ecole centrale de Nantes, 2022. http://www.theses.fr/2022ECDN0051.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Dans tous les problèmes d’agencement, les contraintes de non-chevauchement entre composants et les contraintes d’appartenanceau conteneur sont présentes. Un modèle d’agencement multiobjectif avec contraintes fonctionnelles est développé. Intégrer l’accessibilité des composants comme contraintes fonctionnelles assure la maintenance ou le fonctionnement des composants. Cependant, les contraintes fonctionnelles augmentent la complexité d’optimisation d’agencement, notée indice de capacité. Par conséquent, un nouvel algorithme d’optimisation multiobjectif est proposé en utilisant le placement constructif et le recuit simulé pour rechercher des solutions de compromis entre les objectifs multiples. Ensuite, un indicateur de similarité est défini pour évaluer les similaires entre les solutions proposées par l’algorithme. Les expériences indiquent que l’approche d’optimistion proposée fonctionne bien pour garantir l’accessibilité et trouver efficacement des solutions optimales dans les problèmes industriels d’agencement d’espace à un ou plusieurs conteneurs, où l’analyse de similarité démontre une bonne diversité solutions proposées par l’algorithme, qui peut être appliqué en tant qu’outil interactif outil pour leconcepteur
The conventional layout problem is concerned with finding the arrangements of components inside the container to optimize objectives under geometrical constraints, i.e., no component overlap and no container protrusion. A multi-objective layout model with functional constraints is developed. Integrating the accessibility of components as functional constraints ensures components maintenance or proper operation. However, thefunctional constraints increase the layout optimization complexity, denoted as capacity index. Therefore, a novel multi-objective optimizationalgorithm is proposed using the constructive placement and the simulated annealing to search for compromised solutions between the multiple objectives. Thereafter, a similarity indicator is defined to evaluate how similar optimized layout designs are. The experiments indicate that the proposed optimization approach performs well in ensuring accessibility and efficiently finding high-qualified solutions in single- and multi- container layoutapplications, where the similarity analysis demonstrates good diversity of the obtained layout set, which can be applied as an interactive tool

Carlsson, Oliver, and Marcus Nilsson. "Material placement at Nyköping travel centre construction site." Thesis, Linköpings universitet, Kommunikations- och transportsystem, 2021. http://urn.kb.se/resolve?urn=urn:nbn:se:liu:diva-177541.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

高雲龍 and Wan-lung Ko. "A new optimization model for VLSI placement." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 1998. http://hub.hku.hk/bib/B29812938.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Abels-Eber, Christine. "Histoire de vie d'enfants placés et construction d'historicité." Tours, 1997. http://www.theses.fr/1997TOUR2026.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Cette recherche questionne le rapport que l'enfant placé entretient avec l'événement- séparation qui est à l’ origine de son placement et qu'il vit comme une sanction dont il est le seul responsable. Les enfants placés, qui sont dé-placés pour être replacés, le plus souvent, ne comprennent rien au déroulement de leur vie ; ils sont en perte de repères affectifs et temporels, et n'expriment pas une demande de soin (thérapeutique) mais une demande de compréhension (dans le sens socratique de prendre soin de soi) de leurs préoccupations existentielles. L’histoire de vie étant une recherche et une construction de sens à partir de faits et d'événements temporels personnels et familiaux, mais peu utilisée avec des enfants, nous l'avons tentée avec des enfants placés. Cette démarche a favorisé le mouvement de reconstruction et de travail sur ce que leur contexte de vie a fait d'eux, par le processus de construction-déconstruction-reconstruction, et la situation de co-investissement qui permet de relier le locuteur et l'interlocuteur. Nous avons procédé à une étude compréhensive à partir de trois récits d'enfants placés, de la structure des récits et de l'évolution de ces enfants tout au long de leur récit et de leur travail sur l'énoncé. Cette recherche s'inscrit dans le champ de l'histoire de vie et dans le champ de la sociologie clinique qui renvoie à l'articulation du social et du psychique. L’histoire de vie est interprétée comme outil d'historicité, de travail sur son histoire pour en construire le sens et le cours. Ces trois enfants, par le récit qu'ils ont produit, ont pu affronter les contradictions qui ont traversé leur vie, et tenter de leur donner du sens par les articulations qu'ils sont arrivés à faire entre les évènements et les personnes qui faisaient partie de leur vie ; ils ont pu "réaliser" qu'ils ne sont pas responsables de la séparation qui fut déterminée par les difficultés personnelles, familiales ou sociales de leurs parents. Nous avons considéré la pratique du récit de vie comme l'axe central de la construction identitaire ; l'identité se construit par le rapport que les enfants entretiennent avec la dimension psychique et la dimension sociale de leur vie ; par le récit de leur vie et le questionnement de cette vie, les trois enfants sont parvenus à "sortir d'eux-mêmes" pour interroger leur environnement familial et social…
The subject of this research is the relation of the placed-child to the separating-event which is the reason why he has been placed and is considered for the child as a sanction for which he has be blamed. Children who have been placed, who are out-placed to be placed again do not most of the time understand nothing to the way their existence is evolving; they have been losing their affective and temporal marks, and do not ask for (therapeutic) care but for understand (in the socratic meaning: take care of oneself) of their worries related to the fact they exist. The life story is a search and a building up of meaning which is possible thanks to the analysis of facts and personal as well as family temporal events, but so far this has been seldom used with children; we have tried implement this method with placed children. This method has enhanced the process of re-building and has encouraged them to start working on the consequences on themselves of what they have been undergoing in their lives. This throught a building-break- rebuilding process and the situation of co-investment which creates a link between the speaker and the interlocutor. We have carried out a comprehensive survey based on three stories of placed children, on the stories’ structure and on these children's evolution all along their relating their stories and their analysing their statements. This survey fits in with the life history and the clinic sociology field which refers to the linking of the social and the psychic. This history of life is interpreted as a tool of historicity, of work on one's history, to build up its meaning and direction. Through the relating of their story these three children have been able to cope with the contradictions they have been faced with in their lives. They have intended to give a meaning to these contradictions thanks to the linking they have been able to make between the events and the people in their lives. They have become aware that they were not responsible for the separation which was due to their parent's personal, family or social difficulties. We have been considering the experience of the story telling as the main line in the building of identity; the building of identity is possible thanks to the link the child sets up between the psychic and the social dimensions of his life. Thanks to having related their lifes and having been wondering

Harichandran, Aparna. "Sensor Placement, Operation Identification and Fault Detection for Automated Construction Monitoring." Thesis, Curtin University, 2022. http://hdl.handle.net/20.500.11937/87927.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Her, Shyang-Kuen. "Improved I/O pad positions assignment algorithm for sea-of-gates placement." PDXScholar, 1992. https://pdxscholar.library.pdx.edu/open_access_etds/4316.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

A new heuristic method to improve the I/O pad assignment for the sea-of-gates placement algorithm "PROUD" is proposed. In PROUD, the preplaced I/O pads are used as the boundary conditions in solving sparse linear equations to obtain the optimal module placement. Due to the total wire length determined by the module positions is the strong function of the preplaced I/O pad positions, the optimization of the I/O pad circular order and their assignment to the physical locations on the chip are attempted in the thesis. The proposed I/O pad assignment program is used as a predecessor of PROUD. The results have revealed excellent improvement.

Huang, Xiameng. "Strategic placement of viscous dampers in steel buildings under strong earthquake ground motions." Thesis, University of Warwick, 2018. http://wrap.warwick.ac.uk/102450/.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Supplemental passive dampers are generally considered as an effective tool to control the seismic response of multi-storey buildings. Since the optimum placement of passive dampers in buildings can potentially improve the structural performance or reduce construction cost, there is an increasing number of researchers engaged to optimize the damper placement in buildings. Given that a large number of studies have been conducted to investigate damper placement methods, a systematic method or a clear conclusion for strategically distributing dampers in buildings is not presented in any building guidelines. The main limitations of current damper placement studies may include the lack of focus on collapse resistance of retrofitted buildings, on beam and column nonlinear behaviors, and the lack of considering the variations of earthquake characteristics and intensity levels. The fundamental damper placement issue can be separated as the distribution of dampers throughout the height of the buildings and the distribution of dampers in different bays in building frames. In this research, both distributions are explored and their effect on the collapse performances of buildings under strong earthquakes is thoroughly studied. The effectiveness of advanced damper placement approaches is evaluated by comparisons with classical damper placement methods. Considering the uncertainty in earthquake ground motion characteristics, multiple ground motions scaled to various intensity levels are involved to evaluate the seismic performance of buildings. Finally, major conclusions towards the philosophy of the strategic damper placement in practical building constructions are presented in terms of the overall structural performance under strong ground motions.

Jalkebo, Charlotte. "Placement of Controls in Construction Equipment Using Operators´Sitting Postures : Process and Recommendations." Thesis, Linköpings universitet, Maskinkonstruktion, 2014. http://urn.kb.se/resolve?urn=urn:nbn:se:liu:diva-108980.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

An ergonomically designed work environment may decrease work related musculoskeletal disorders, lead to less sick leaves and increase production time for operators and companies all around the world. Volvo Construction Equipment wants to deepen the knowledge and investigate more carefully how operators are actually sitting whilst operating the machines, how this affects placement of controls and furthermore optimize controls placements accordingly. The purpose is to enhance their product development process by suggesting guidelines for control placement with improved ergonomics based on operators’ sitting postures. The goal is to deliver a process which identifies and transfers sitting postures to RAMSIS and uses them for control placement recommendations in the cab and operator environments. Delimitations concerns: physical ergonomics, 80% usability of the resulted process on the machine types, and the level of detail for controls and their placements. Research, analysis, interviews, test driving of machines, video recordings of operators and the ergonomic software RAMSIS has served as base for analysis. The analysis led to (i) the conclusion that sitting postures affect optimal ergonomic placement of controls, though not ISO-standards, (ii) the conclusion that RAMSIS heavy truck postures does not seem to correspond to Volvo CE’s operators’ sitting postures and (iii) and to an advanced engineering project process suitable for all machine types and applicable in the product development process. The result can also be used for other machines than construction equipment. The resulted process consists of three independent sub-processes with step by step explanations and recommendations of; (i) what information that needs to be gathered, (ii) how to identify and transfer sitting postures into RAMSIS, (iii) how to use RAMSIS to create e design aid for recommended control placement. The thesis also contains additional enhancements to Volvo CE’s product development process with focus on ergonomics. A conclusion is that the use of motion capture could not be verified to work for Volvo Construction Equipment, though it was verified that if motion capture works, the process works. Another conclusion is that the suggested body landmarks not could be verified that they are all needed for this purpose except for those needed for control placement. Though they are based on previous sitting posture identification in vehicles and only those that also occur in RAMSIS are recommended, and therefore they can be used. This thesis also questions the most important parameters for interior vehicle design (hip- and eye locations) and suggests that shoulder locations are just as important. The thesis concluded five parameters for control categorization, and added seven categories in addition to those mentioned in the ISO-standards. Other contradictions and loopholes in the ISO-standards were identified, highlighted and discussed. Suggestions for improving the ergonomic analyses in RAMSIS can also be found in this report. More future research mentioned is more details on control placement as well as research regarding sitting postures are suggested. If the resulted process is delimited to concern upper body postures, other methods for posture identification may be used.

Hand, Erin Marlene Flowers. "Speech Understanding in Noise as a Function of Microphone Placement in Hearing Aids." PDXScholar, 1996. https://pdxscholar.library.pdx.edu/open_access_etds/5190.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Hearing aid users often complain of poor speech understanding in the presence of background noise. There have been many attempts to overcome this problem by hearing aid manufactures and dispensers. The purpose of the present study was to determine if differences existed between three different styles of hearing aids (i.e. in the ear (ITE), in the canal (ITC), and completely in the canal (CIC)) in the presence of a multi-talker babble. Five sensori-neural hearing impaired subjects were selected from the Portland State University audiology clinic. The subjects were required to listen to a recording of the California Consonant Test (CCT) against a background noise of multi-talker babble. Stimuli were presented through headphones in the sound booth. The stimuli were recorded through three different hearing aids placed on KEMAR's left ear and adjusted to a 10 dB signal-to-noise ratio. Once the speech samples were recorded and digitized, they were routed through a GSl-16 audiometer to the listener. In order to determine performance differences across the three hearing aid configurations from within a single-subject design, each subject's performance was compared in a pairwise fashion between the hearing aid configurations. An analysis of the data was completed using the Randomization test. Using this statistical model, no significant difference was found between the individual scores. Further research is warranted to determine if a better measure exists that qualitatively defines the effect of microphone placement on speech understanding ability in hearing aid users.

Більше джерел

Книги з теми "Constructive placement":

Griffiths, Roger. Well placement fundamentals. Sugar Land, TX: Schlumberger, 2009.

Знайти повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Halsted, Byron D. Barns, sheds & outbuildings: Placement, design, and construction. Brattleboro, Vt: A.C. Hood, 1994.

Знайти повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Stein, Emma Natalya. Constructing Kanchi. NL Amsterdam: Amsterdam University Press, 2021. http://dx.doi.org/10.5117/9789463729123.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

This book traces the emergence of the South Indian city of Kanchi as a major royal capital and multireligious pilgrimage destination during the era of the Pallava and Chola dynasties (circa seventh through thirteenth centuries). It presents the first-ever comprehensive picture of historical Kanchi, locating the city and its more than 100 spectacular Hindu temples at the heart of commercial and artistic exchange that spanned India, Southeast Asia, and China. The author demonstrates that Kanchi was structured with a hidden urban plan, which determined the placement and orientation of temples around a central thoroughfare that was also a burgeoning pilgrimage route. Moving outwards from the city, she shows how the transportation networks, river systems, residential enclaves, and agrarian estates all contributed to the vibrancy of Kanchi’s temple life. The construction and ongoing renovation of temples in and around the city, she concludes, has enabled Kanchi to thrive continuously from at least the eighth century, through the colonial period, and up until the present.

Sechen, Carl. VLSI placement and global routing using simulated annealing. Boston: Kluwer Academic Publishers, 1988.

Знайти повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Boffo, Vanna, Sabina Falconi, and Tamara Zappaterra, eds. Per una formazione al lavoro. Florence: Firenze University Press, 2012. http://dx.doi.org/10.36253/978-88-6655-304-5.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

The volume is a collection of the papers from a study seminar held at the University of Florence Faculty of Education and Training Sciences in March 2012 entitled Formazione e orientamento al lavoro. Le sfide della disabilità adulta. The aim of the initiative was to highlight a topic/problem which has little or no resonance in civil society, or in study and research contexts, namely, training and career guidance for disabled adults. The volume also recounts a course of studies carried out by Le Rose, a cooperative from the municipality of Florence, involving empirical research on the relationship between disability and job placement. As well as proposing an interdisciplinary and multifaceted reflection on a definitely innovative topic, the intention is to emphasize the central place of work in the lives of all people and the role that suitable education and training plays in constructing the adult identity. Care for the place where the job training is carried out, as well as attention to the relationships and actions pursued by the workers undertaking to develop job placement programmes, are central dimensions for the construction of a renewed culture of inclusion, citizenship and social and personal recognition.

International RILEM Symposium on Self-Compacting Concrete (6th 2010 Montréal, Québec). Design, production and placement of self-consolidating concrete: Proceedings of SCC2010, Montreal, Canada, September 26-29, 2010. Edited by Khayat Kamal, Feys Dimitri, SpringerLink (Online service), and North-American Conference on the Design and Use of SCC (4th : 2010 : Montréal, Québec). Dordrecht: Springer, 2010.

Знайти повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Cope, Ronald Thomas. Application of Equipercentile techniques to test scale construction: Scaling and equating of the ACT ASSET placement test battery. Iowa City, Iowa: American College Testing Program, 1989.

Знайти повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Commission, Virginia State Corporation. Placement of utility distribution lines underground: Report of the State Corporation Commission to the Governor and the General Assembly of Virginia. Richmond, Va: Commonwealth of Virginia, 2005.

Знайти повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Moser, A. P. Buried pipe design. 2nd ed. New York: McGraw-Hill, 2001.

Знайти повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Moser, A. P. Buried pipe design. 3rd ed. Logan, Utah: McGraw-Hill, 2008.

Знайти повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Більше джерел

Частини книг з теми "Constructive placement":

Taylor, Lisa. "Workbook – Reflection, consolidation, design and delivery of an online work-based learning placement." In Constructing Online Work-Based Learning Placements, 108–16. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-9.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Taylor, Lisa. "Peer group learning." In Constructing Online Work-Based Learning Placements, 43–53. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-4.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Taylor, Lisa. "Theory into practice – A case example." In Constructing Online Work-Based Learning Placements, 93–107. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-8.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Taylor, Lisa. "Online learning in a world of ‘place’." In Constructing Online Work-Based Learning Placements, 14–27. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-2.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Taylor, Lisa. "Reflection to support learning." In Constructing Online Work-Based Learning Placements, 54–65. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-5.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Taylor, Lisa. "Employability and the online work-based learning placement environment." In Constructing Online Work-Based Learning Placements, 28–42. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-3.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Taylor, Lisa. "Feedback and supervision." In Constructing Online Work-Based Learning Placements, 79–92. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-7.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Taylor, Lisa. "Learning outcomes and assessment." In Constructing Online Work-Based Learning Placements, 66–78. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-6.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Taylor, Lisa. "Work-based learning placements within higher education." In Constructing Online Work-Based Learning Placements, 1–13. New York: Routledge, 2023. http://dx.doi.org/10.4324/9781003315872-1.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Jaud, Š., S. Esser, A. Borrmann, L. Wikström, S. Muhič, and J. Mirtschin. "A critical analysis of linear placement in IFC models." In ECPPM 2021 – eWork and eBusiness in Architecture, Engineering and Construction, 12–20. London: CRC Press, 2021. http://dx.doi.org/10.1201/9781003191476-2.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Тези доповідей конференцій з теми "Constructive placement":

Papa, David A., Saurabh N. Adya, and Igor L. Markov. "Constructive benchmarking for placement." In Proceedins of the 14th ACM Great Lakes symposium. New York, New York, USA: ACM Press, 2004. http://dx.doi.org/10.1145/988952.988981.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Lin, Ichiang, and David H. C. Du. "Performance-driven constructive placement." In Conference proceedings. New York, New York, USA: ACM Press, 1990. http://dx.doi.org/10.1145/123186.123235.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Kim, Sungjae, Eugene Shragowitz, George Karypis, and Rung-Bin Lin. "Interleaving of Gate Sizing and Constructive Placement for Predictable Performance." In 2007 International Symposium on VLSI Design, Automation and Test. IEEE, 2007. http://dx.doi.org/10.1109/vdat.2007.373225.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

da Silva, Ivo Chaves, Sandoval Carneiro, Edimar Jose Oliveira, Jeferson de Souza Costa, Jose Luiz R. Pereira, and Paulo Augusto N. Garcia. "A Heuristic Constructive Algorithm for capacitor placement on distribution systems." In 2009 IEEE/PES Power Systems Conference and Exposition (PSCE 2009). IEEE, 2009. http://dx.doi.org/10.1109/psce.2009.4840033.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Karmokar, Nibedita, Arvind K. Sharma, Jitesh Poojary, Meghna Madhusudan, Ramesh Harjani, and Sachin S. Sapatnekar. "Constructive Common-Centroid Placement and Routing for Binary-Weighted Capacitor Arrays." In 2022 Design, Automation & Test in Europe Conference & Exhibition (DATE). IEEE, 2022. http://dx.doi.org/10.23919/date54114.2022.9774640.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Sutanthavibul, Suphachai, and Eugene Shragowitz. "Dynamic prediction of critical paths and nets for constructive timing-driven placement." In the 28th conference. New York, New York, USA: ACM Press, 1991. http://dx.doi.org/10.1145/127601.127165.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Sim, Siang-Kok, Meng-Leong Tay, and Ahmad Khairyanto. "Optimisation of a Robotic Workcell Layout Using Genetic Algorithms." In ASME 2005 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. ASMEDC, 2005. http://dx.doi.org/10.1115/detc2005-85518.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

With the advent of robots in modern-day manufacturing workcells, optimization of robotic workcell layout (RWL) is crucial in ensuring the minimization of the production cycle time. Although RWL share many aspects with the well-known facility layout problem (FLP), there are features which set the RWL apart. However, the common features which they share enable approaches in FLP to be ported over to RWL. One heuristic gaining popularity is genetic algorithm (GA). In this paper, we present a GA approach to optimizing RWL by using the distance covered by the robot arm as a means of gauging the degree of optimization. The approach is constructive: the different stations within the workcell are placed one by one in the development of the layout. The placement method adopted is based on the spiral placement method first broached by Islier (1998). The algorithm was implemented in Visual C++ and a case study assessed its performance.

Hussary, N., J. Schein, and J. Heberlein. "Control of Jet Convergence in Wire Arc Spray Systems." In ITSC 1999, edited by E. Lugscheider and P. A. Kammer. Verlag für Schweißen und verwandte Verfahren DVS-Verlag GmbH, 1999. http://dx.doi.org/10.31399/asm.cp.itsc1999p0335.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Abstract This paper aims to achieve improved control over the spray pattern in a wire arc torch by means of constructive measures to influence the flow dynamics. It focuses on evaluating different fluid dynamic designs of the spray torches with respect to the droplet trajectories and velocity distributions and the deposit distribution. First, the paper describes the approaches for novel nozzle designs including the addition of shrouds and the torch evaluation diagnostics, and then presents the results for four different nozzle arrangements. It is observed that the nozzle design and the placement of the wire tips within the nozzle have the greatest effect on the divergence of the spray pattern. Paper includes a German-language abstract.

Albahttiti, Mohammed T., Ahmad A. Ghadban, Kyle A. Riding, and David Lange. "Air Entrainment and the Fabrication of Concrete Railroad Ties." In 2015 Joint Rail Conference. American Society of Mechanical Engineers, 2015. http://dx.doi.org/10.1115/jrc2015-5671.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Handling and vibration can affect the air content of prestressed concrete railroad ties. The amount and variation in vibration experienced in concrete railroad ties were investigated to determine the concrete fabrication conditions typically used. Two methods of fabrication were investigated by measuring the concrete properties and vibration exposure during placement at two concrete tie manufacturing plants. In addition to measuring the vibration distribution in concrete railroad ties, a pair of ties were selected for hardened-air void analyses to determine any variation of air content in relation to the height of the ties. The vibration results indicate the existence of constructive and destructive wave-interferences in tie cavities. These interferences may contribute to large variations in the vibration acceleration throughout the length, depth, and width of concrete crossties during fabrication. This may account for the air-loss across the depth of the ties.

Owens, Patrick D., and A. Galip Ulsoy. "Self-Reproducing Machines: Preventing Degeneracy." In ASME 2006 International Mechanical Engineering Congress and Exposition. ASMEDC, 2006. http://dx.doi.org/10.1115/imece2006-14201.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Machines produced by humans exhibit insufficient complexity to produce similar machines. As John von Neumann originally postulated, if biological systems are able to successfully reproduce, then there must be some characteristic that we can embed in machines to give them the ability to reproduce. Such a self-reproductive machine, also imbued with the ability to do constructive work, could prove enormously useful to the human race. This paper considers a simple self-reproducing machine, which consists of a 2-DOF, planar robot arm capable of picking up and placing the components of another arm. If the robot places the components within the allowable tolerance, then the original arm has successfully reproduced. An assembly line is constructed, so that a self-reproduction process can proceed along a track. If this process eventually fails because one robot is not capable of assembling another, then the system is said to be degenerate. Otherwise, the system is sustainable. A kinematic model that maps component placement errors from one generation of the robot arm to the next was derived. The system exhibited exponential growth in component placement errors. Thus, this self-reproduction system is degenerate. This system is then augmented to provide error-correction during the assembly process. With the application of error-correction the self-reproduction process is made sustainable. The minimal amount of error-correction required to achieve sustainable self-reproduction was investigated through sensor quantization, and it was shown that the amount of fidelity in the error-correction signal determines the success of the self-reproduction process. This self-reproduction system was also analyzed in the context of Kabamba's Generation Theory, which could predict the results obtained through simulation regarding degeneracy or sustainability.

Звіти організацій з теми "Constructive placement":

Krafft, Douglas, Rachel Bain, Jack Cadigan, and Richard Styles. A review of tidal embayment shoaling mechanisms in the context of future wetland placement. Engineer Research and Development Center (U.S.), December 2022. http://dx.doi.org/10.21079/11681/46143.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Wetland construction in tidally influenced embayments is a strategy for beneficial use of sediment dredged from nearby navigation channels. These projects have the potential to alter basin morphology, tidal hydrodynamics, and shoaling trends. This special report provides a broad review of the literature related to engineering-induced changes in tidal range, salinity, tidal prism, tidal asymmetry, and other known causes of shoaling. Each potential shoaling mechanism is then evaluated in the context of wetland placement to provide a foundation for future beneficial use research. Based on a compilation of worldwide examples, wetland placement may reduce tidal amplitude and enhance ebb current dominance, thus reducing shoaling rates in the channels. However, constructed wetlands could also reduce the embayment’s tidal prism and cause accelerated shoaling relative to the pre-engineered rate. Because constructed wetlands are often created in conjunction with navigation channel dredging, the system’s morphologic response to wetland construction is likely to be superimposed upon its response to channel deepening, and the net effect may vary depending on a variety of system-specific parameters. Planning for future wetland placements should include an evaluation of local hydrodynamic behavior considering these factors to predict site-specific response.

Perkey, David, and Danielle Tarpley. Using geophysical and erosion properties to identify potential beneficial use applications for Atlantic Intracoastal Waterway sediments. Engineer Research and Development Center (U.S.), July 2022. http://dx.doi.org/10.21079/11681/44825.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

In an effort to identify alternative and beneficial use placement strategies for dredged sediments from the Atlantic Intracoastal Waterway (AIWW), the US Army Corps of Engineers, Savannah District (SAS), and the US Army Engineer Research and Development Center (ERDC) performed a series of physical property tests of 34 core borings from the SAS AIWW. Physical property testing found that 14 of the borings were non-cohesive sandy materials that may be suitable for potential beach renourishment or berm construction. The remaining 20 borings had mud contents sufficient enough to result in cohesive behavior. A subset of six of these materials from across the geographic region were further evaluated to characterize their erosion behavior. Following a self-weight consolidation period of 30 days, erosion testing showed that the tested cohesive sediments had critical shear stress values that ranged from 1.7 Pa to 2.9 Pa, suggesting that these sediments would likely be resistant to erosion in most wetland environments after placement. Additionally, the cohesive sediments were found to produce gravel-sized mud clasts. These clasts could account for 20% or more of the eroded mass and significantly reduce the amount of silts and clays incorporated in suspended plumes during and immediately following placement.

Perkey, David W., Danielle R. N. Tarpley, and Renée M. Styles. Using Geophysical and Erosion Properties to Identify Potential Beneficial Use Applications for Atlantic Intracoastal Waterway Sediments. U.S. Army Engineer Research and Development Center, July 2022. http://dx.doi.org/10.21079/11681/44906.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

Mudryj, Igor, and Igor Ivaneіko. The Use of Small Drilling Equipment in the Arrangement of Pile Foundations in Compressed Conditions. Intellectual Archive, September 2022. http://dx.doi.org/10.32370/ia_2022_09_11.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

The procedure for finding technological parameters for the installation of pile foundations with small-sized drilling rigs, when developing design and technological documentation in compressed construction conditions, is considered. Methodological approaches to the choice of technologies for the construction of pile foundations are shown, depending on the dimensions of the small-sized drilling machines used, the required area for their placement, storage areas, and auxiliary equipment. in compressed conditions of construction. The existing normative documents do not set out separate requirements for the development of projects for the execution of works in compressed construction conditions, these norms do not provide for the definition of rational erection schemes for the selected set of mechanization in the dimensions of a specific construction site, which is characterized by various restrictions and obstacles. The proposed requirements for the use of mechanization methods in the conditions of compacted buildings during the installation of pile foundations based on a preliminary analysis of the parameters of the construction site: engineering and geological condition of the site; internal brevity of the designed structure; external brevity of the construction site; dimensions of the driving car; sites for the location of additional equipment, warehouses, unloading areas. Taking into account practical experience in the development of work projects and the analysis of current regulatory documents, made it possible to establish the main requirements for the use of small-sized drilling rigs in densely built-up conditions.

Seiple, Jacqueline, Luis Santiago, Christopher Spaur, Safra Altman, Matthew Balazik, Thomas Laczo, Daniel Mensah, Warunika Amarasingha, Andrew Payson, and Danielle Szimanski. Two years of post-project monitoring of a navigation solution in a dynamic coastal environment, Smith Island, Maryland. Engineer Research and Development Center (U.S.), June 2022. http://dx.doi.org/10.21079/11681/44620.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

In 2018, jetties and a sill were constructed by the US Army Corps of Engineers adjacent to the Sheep Pen Gut Federal Channel at Rhodes Point, Smith Island, Maryland. These navigation improvements were constructed under Section 107 of the Continuing Authorities Program. Material dredged for construction of the structures and realignment of the channel were used to restore degraded marsh. Following construction and dredging, 2 years of monitoring were performed to evaluate the performance of navigation improvements with respect to the prevention of shoaling within the channel, shoreline changes, and impacts to submerged aquatic vegetation (SAV). Technical Report ERDC/CHL TR-20-14 describes the first year of post-project monitoring and the methodologies employed. This report describes conclusions derived from 2 years of monitoring. While the navigation improvements are largely preventing the channel from infilling, shoaling within is occurring at rates higher than expected. The placement site appears stable and accreting landward; however, there continues to be erosion along the shoreline and through the gaps in the breakwaters. SAV monitoring indicates that SAV is not present in the project footprint, even though turbidity is comparable to the reference area. Physical disturbance of the bottom sediment during construction may explain SAV absence.

Jansson, Anna, Arun Heer, Suzana Rice, Frank Buonaiuto, Danielle Tommaso, Lynn Bocamazo, Stephen Couch, and Jodi McDonald. South Shore of Long Island, New York Regional Sediment Management Investigation : an overview of challenges and opportunities. Engineer Research and Development Center (U.S.), April 2022. http://dx.doi.org/10.21079/11681/43920.

Повний текст джерела

Стилі APA, Harvard, Vancouver, ISO та ін.

Анотація:

The US Army Corps of Engineers (USACE) is conducting the “South Shore of Long Island, New York Regional Sediment Management Investigation” to further understand sediment dynamics and to develop a comprehensive regional sediment management plan for the south shore of Long Island, New York. Regional sediment management is a systems approach using best management practices for more efficient and effective use of sediments in coastal, estuarine, and inland environments. This investigation seeks to characterize sediment movement on the south shore of Long Island as a holistic system across the entire study area. It focuses on the regional system post-Hurricane Sandy (October 2012) as the storm significantly altered the physical landscape with severe shoreline erosion, which resulted in the construction of projects to reduce the risk of future storms and stakeholder priorities with a new emphasis on bay-side sediment dynamics, such as channel shoaling and disappearing wetlands. Despite the fact the storm caused severe erosion, the equilibrium beach profile, depth of closure, and general shoreline orientation seem to be unaffected. Previous studies have characterized sediment movement at specific sections of the south shore, but these data have not been incorporated to create a system-wide perspective. Coordinating sediment management across the six Atlantic Ocean inlets, Great South Bay Channel, Intracoastal Waterway, and coastal storm risk management (CSRM) projects could save the federal government millions of dollars in dredging and sand placement actions. This technical note presents the progress the investigation has made to date and will be followed with a more in-depth technical report titled South Shore of Long Island, New York Regional Sediment Management Investigation: A Post-Hurricane Sandy Shoreline Evaluation, currently in preparation.